What Size Hole is the Uni-Lite LED Side Marker Light # MCL11AKB Designed to Install In
Question:
What is the minimum mounting thickness that is needed to get a watertight seal with these?
asked by: Kent K
Expert Reply:
The Sealed, Glolight Uni-Lite Mini LED Side Marker and Clearance Light # MCL11AKB is designed to fit an 11/16 inch diameter hole. While this light is considered submersible, it is not designed to provide a watertight seal when installed though.
You would have to use a watertight sealant between the grommet and the hole it would get installed into, as well as between the light and the grommet.
Submersible means that the light itself can be submerged underwater and it won't become damaged. It is still recommended that you unplug your trailer wiring before backing your boat trailer into the water of a boat ramp though.
I attached a review video for you to check out as well.
Product Page this Question was Asked From
Uni-Lite LED Clearance and Side Marker Light w Grommet - Submersible - 2 Diodes - Amber Lens
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Recessed Mount
- Submersible Lights
- LED Light
- 3/4 Inch Diameter
- Amber
- Optronics
more information >
Continue Researching
- Shop: Uni-Lite LED Clearance and Side Marker Light w Grommet - Submersible - 2 Diodes - Amber Lens
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Shop: LED Bullet Clearance or Side Marker Trailer Light with Grommet - 3 Diodes - Amber Lens
- Shop: Peterson LED Mini Clearance and Side Marker Trailer Light w/ Grommet - 1 Diode - Round - Amber Lens
- Search Results: 3 prong pigtail
- Search Results: mcl11akb
- Search Results: 3 pin connector
- Video: Command LED Bullet Clearance or Side Marker Trailer Light with Grommet Installation
- Q&A: What is the Wire Gauge Used for Right Angle 3-Wire Pigtail # A47PB
- Q&A: Replacement Amber Clearance Light For Trailer with Existing 1 Inch Diameter Hole
- Q&A: Installation Tips for a Sealed, Uni-Lite Mini LED Side Marker Light # MCL11AKB
- Q&A: What Hole Size Should Be Drilled to Install the # MCL11AKB MiniLED Round Clearance Light
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Search Results: 3500 brakes
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Shop: Trailer Hitch
- Search Results: 25580
- Article: Trailer Wiring Diagrams
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Shop: Trailer Wiring
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Search Results: 44649
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: dust cap
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Shop: Brake Controller
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Most Popular Wheel Bearings