Jack Recommendation for a Trailer that has a Pipe Mount that Is 2-3/8 Inch OD and 2 inch ID
Question:
I have a 1988 4 Winns trailer under my 4 Winns 20 Captiva deck boat. The weld on trailer jack stand needs replacement. I measure the outer tube diameter to be between 2-3/8 and 2-7/16inch and the inner tube diameter of 2. Might you have a jack to fit the welded mount?
asked by: Jim B
Expert Reply:
The Bulldog Round, Pipe-Mount Swivel Jack # BD178203 is designed to fit a pipe mount that has a 2-1/2 inch outer diameter and a 2 inch inner diameter which is very close to what you have on your trailer. As long as the pin hole on your pipe mount is 5/8 inch in diameter this jack would work well for you. I attached a review video for you to check out as well.
This is a 5,000 lb jack that should work well for you.
![Jameson C](https://images.etrailer.com/static/images/catg/people/371_tn.jpg)
Product Page this Question was Asked From
Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- Swivel Jack
- 15 Inch Lift
- Pipe Mount
- Weld-On
- With Rectangle Foot
- Bulldog
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs
- Shop: Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate - Topwind - 15" Lift - 5,000 lbs
- Video: Bulldog Trailer Jack - A-Frame Jack - BD1700100317 Review
- Search Results: chocks
- Q&A: Outer Pipe Mount Diameter for Pro Series Round, Pipe-Mount Swivel Jack
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Search Results: 44649
- Shop: Grease Seals 10-36 (pair)
- Article: Trailer Wiring Diagrams
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: 25580
- Video: Lippert Solera Slider Slide-Topper Review
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Dust Cap for Kodiak Disc Brake Kit
- Article: Trailer Tire Sizing
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Video: Roadmaster Automatic Battery Disconnect Installation - 2020 GMC Sierra 1500
- Shop: Fifth Wheel Hitch
- Search Results: 68149
- Shop: Brake Controller
- Q&A: 2022 Toyota Highlander Wiring for a 7-Way Blade Connector
- Shop: Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option - Black
- Search Results: dust cap
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Gooseneck Hitch
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End