What Wiring Adapter Needed to Connect Prodigy P3 Brake Controller # 90195 in 2015 Toyota Tacoma

Question

Question:

NEED A FACTORY harness connector p3 brake controller to factory connector please one for my 2015 toyota tacoma with factory tow package thanks

asked by: TODD V

0

Expert Reply:

To connect your Tekonsha Prodigy P3 Trailer Brake Controller # 90195 in your 2015 Toyota Tacoma that has the factory tow package you will use part # 3040-P. This quick-connect harness plug in between the P3 and the port underneath the dash. The linked installation video illustrates the process in a 2012 Tacoma. Written instructions are also provided.

expert reply by: Adam R

0

Answer 1

The 2015 Toyota Tacoma is part of the third generation of this vehicle and the location of the brake controller connection port is behind the left kick panel, near the emergency brake pedal. Please refer to the linked video at the :20-second mark for…

view full answer...

Answer 2

The two parts you referenced do include a brake controller and an install harness for your 2013 Toyota Tacoma. The part #3040-P is the install harness and the part #90195 is the brake controller. I attached an install video that shows the two parts…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 7

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 8

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 9

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 10

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

Answer 11

You are correct, you should only be getting output when the brake is applied, or the override switch is activated. It sounds like the controller might be bad, but to make sure, you should probably bench test it before tossing it. Use a circuit…

view full answer...

Answer 12

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

What Wiring Adapter Needed to Connect Prodigy P3 Brake Controller # 90195 in 2015 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching