Replacement Gooseneck Ball for Mopar Ram Hitch Prep Package

Question

Question:

Will this fit a dodge 3500 with factory equipment

asked by: James

0

Expert Reply:

The Replacement Hitch Ball # BWGNXA2000 is designed to fit B and W Turnover hitches. Since you said you have factory equipment I am assuming you mean you have the Mopar hitch prep package and are in need of a gooseneck ball.

If so, you would actually need the part # C60601, or part # RP30140 if you want the safety chain loops as well.

expert reply by: Jameson C

0

Answer 1

For a ladder rack that is compatible with the RetraxONE XR #RTT-60232 I recommend the Telescoping Rack for TruXedo Elevate Rack System #TX84NV. This is an adjustable rack that can sit at 18" or 28" high. It is also a sliding rack that will…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 10

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 11

Usually ladder racks use the inside edge of the top of the bed site to attach to the vehicle, but luckily there are exceptions to that. The Thule TracRac SR is typically compatible with tonneau covers that mount to the inside edges of the truck bed.…

view full answer...

Answer 12

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Replacement Gooseneck Ball for Mopar Ram Hitch Prep Package

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching