Replacement Grease Zerk for Ram Jacks

See what our Experts say about this etrailer Accessories and Parts

• Are E-Z Lube Grease Zerks Threaded or Pressed In
  The E-Z Lube grease zerks are threaded in, and if you can remove your zerk with the threads not damaged, people have had success replacing it with the Replacement Grease Zerk # Gzerk. The zerks have a standard 1/4" pipe thread fitting which is what this zerk has.
  view full answer...
• What Size Zerk Fittings Does Dexter Equalizer Use
  We have confirmed with Dexter that the EZ lube spindles on their axles have a standard 1/4" pipe thread fitting that can be replaced with part # Gzerk that we carry. We don't carry an angled version of this though.
  view full answer...
• Replacement Threaded Grease Fitting For Dexter Suspension Kit with Wet Bolts
  For your Dexter E-Z Flex Suspension Kit # K71-652-00 wet bolts the grease zerk replacement isn't specified. It is the standard 1/4 inch thread and if so you want is the Replacement Grease Zerk for Ram Jacks # Gzerk but you will want to make sure that your broken zerk didn't harm the threads inside the bolt. Since it broke off, I recommend you replace the entire bolt using the Step Wet Bolt for 1-3/4" Double Eye Springs # 34007-187-00. This is a confirmed replacement.
  view full answer...
• Missing Zerk Fitting on Boat Trailer Grease Repack
  Thanks for the pictures. It looks like your zerk fitting has broken off. You should have a standard 1/4" grease zerk fitting if you have EZ Lube spindles. You would be able to replace it with the Grease Zerk for Ram Jacks item # Gzerk.
  view full answer...
  
• Correct EZ Lube Spindle nut and Washer Kit for my Trailer
  Not having a cotter pin is not acceptable but because it is an EZ-Lube hub it should use the Spindle Nut Kit for EZ Lube Axles part # RG05-100. This has the tang retaining washer to keep the nut from backing off. As far as the grease zerk they are threaded. If yours are broken off you will need to drill them out carefully and tap the hole to match a grease zerk you want to use these are readily available at any parts store or you can use part # Gzerk.
  view full answer...
• Replacement Zerk Fitting for 6K Dexter E-Z Flex Suspension Kit
  Hey Trevor, thanks for reaching out! To replace the grease Zerk fitting that came with your 6K Dexter E-Z Flex Suspension Kit # K71-652-00 you'll need part # Gzerk, which we've confirmed matches the specs from Dexter Axle.
  view full answer...
• Solution for Zerk Fitting of EZ Lube Spindle Wearing Out Rubber Cover
  Your zerk fittings are probably press-in ones. Before you try to remove them you might see if you can find ones that are shorter than what you have. From there I would maybe try finding someone with access to a press or a welder with trailer spindle experience who could remove yours without damaging them and press in new ones. One thing I'd like to add is that we generally don't like the EZ lube or Bearing Buddy types of ways to add grease to a hub as they often allow people to over fill...
  view full answer...
• Replacement Grease Zerk for EZ Lube Spindle
  The grease zerk used in their EZ Lube spindles like # TRU74FR is a standard 1/4-inch pipe thread fitting that you can replace with an item like # Gzerk. Your local hardware store may have one too. You can use a grease gun kit like # L30132 on this fitting.
  view full answer...
• How To Fix/Replace Grease Zerk Fitting on a Dexter EZ-Lub Axle
  The grease zerk fittings on a Dexter EZ-Lub Axle are threaded. If you broken off the one you have now you can use a screw/bolt extractor to remove the remaining threads and then use the Replacement Grease Zerk part # Gzerk to replace it which I can confirm will fit. If you can't get the old threads out or damage them in the process you can just leave it as is and install a set of Bearing Buddy Bearing Protectors like part # BB1980A. In order to confirm the correct Bearing Buddy Bearing...
  view full answer...
• Replacement Zerk Fitting Recommendation for Dexter EZ Lube Spindle
  I confirmed with my contact at Dexter Axle that the grease zerk used in their EZ Lube spindles like # TRU74FR is a standard 1/4-inch pipe thread fitting that you can replace with an item like # Gzerk. Your local hardware store may have one too. You can use a grease gun kit like # L30132 on this fitting.
  view full answer...
• Replacement Grease Caps For Hub Bore 1.781 With Grease Zerk On Cap For Adding Grease To Spindle
  It appears that you have a Fulton Grease Cap # F001503 that fits a 1.781 hub bore. And that someone put in a Grease Zerk # Gzerk on the cap. If you can confirm that is you hub bore diameter as I cannot tell from your tape measure, you can use the previous cap. Or you can use the Bearing Buddy Bearing Protectors # BB1781SS that are designed to do what your caps are doing.
  view full answer...
  
• Replacing The Zerk Fitting On A Dexter EZ-Lube Trailer Axle
  The zerk fittings on the Dexter Trailer Axle # T3584F-EZ-8974 are a 1/4" pipe thread. If you need a replacement zerk fitting you can use part # Gzerk, which we have confirmed to fit the Dexter Ez-Lube Axles.
  view full answer...
• Do Both Sides of TruTrack Weight Distribution Head Need to be Greased
  The head unit on the Curt TruTrack Weight Distribution System w/ Sway Control # C17501 should have a grease zerk fitting on both of the trunnion bar attachments as you can see in the attached photo. The instructions just show one side to save space in the instructions. Since the one you have is missing one of the fittings you'll either need to replace it on your end with part # Gzerk (which I confirmed matches with my contact at Curt) or pursue the warranty of the item if it still applies...
  view full answer...
  
• Replacement Grease Zerk For Dexter EZ-Lube Axle On Older Trailer
  We have confirmed with Dexter that the EZ lube spindles on their axles have a standard 1/4" pipe thread fitting that can be replaced with part # Gzerk.
  view full answer...
• Replacement Zerk Fitting For A 2022 Triton LTWCI PWC Trailer
  The grease zerk fittings on your Dexter EZ-Lube axle are threaded. Since one of the fittings broke off you can use a screw/bolt extractor to remove the remaining threads. When the replacement threads are out you can install The Replacement Grease Zerk # Gzerk to replace it. If you're having trouble getting the old threads out or removed you can install The Bearing Buddy Bearing Protectors # BB1980A-SS. You will have to measure the diameter of your grease cap. The # BB1980A-SS will fit...
  view full answer...
• Replacement Zerk Fitting for etrailer Jack # TJP-5001S-B
  We actually have a replacement zerk fitting for all of the etrailer/Ram trailer jacks with the part # Gzerk. This is a standard 1/4 inch pipe thread.
  view full answer...
• EZ Lube Grease Cap Hitting Grease Fitting
  I do have a solution that will work with your EZ Lube axles. It sounds like the grease fitting is too long and is hitting the rubber cap. Most grease caps are very similar in height, so changing the cap most likely won't solve the clearance issue. However changing out the grease zerk will give you more clearance, if you use a short one like # Gzerk. If the fitting was bent, or damaged and then replaced, it's very possible to have one that is just slightly too long. I verified with my...
  view full answer...

Do you have a question about this Accessories and Part?