To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's tail light wiring connectors located in the tail light housing and accessed through the trunk and routed to the trunk light wiring which is accessed under the vehicle.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
Average Customer Rating: 4.6 out of 5 stars (13 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.Wrong size. When I took wiring harness to my mechanic he said it would not be a quick way to wire
Bought from another source
Wiring harness did not have the right year on it and said it was for all wheel drive and I don’t have all wheel drive.
Laraine
1/9/2024
2022 Toyota Prius eco FWD
good product ..i did my whole install on ramps in three hours..its smart to do wireing first..you can intall hitch alone if you take the rear outside facia off and put one long extra bolt in bacwards on each side to halp aloghnment while holding both in place with one hand.be carefull not to let fall on you!
Fit exactly video , plus written instructions made it a breeze.
Fast, friendly service. Arrived on time
I purchased a Curt harness for my 2019 Toyota Prius AWD-e. The order was confirm almost immediately. The order arrived in the mail 1-1/2 days later. The instructions were clear and precise. 2 hours later, everything worked just as it should and I was pulling my ultralite utility trailer to the landfill.
Thank you etrailer and Curt.
Please update Curt that this is the correct cable for 2020 Prius... Regular Prius.
ease of installation, fit.
Nice
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Katrina D.
1/9/2024
I am sorry for any confusion on this. I have gotten in contact with the manufacturer and they have confirmed that, yes this fits an AWD Prius. We would need to know what you do have to recommend the correct harness.