Roof Rack Includes:
Part Numbers: INXB100-108,INXS400,IN93FR
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming.
Features:
Specs:
These low-profile Inno Aero crossbars let you build a stylish, aerodynamic roof rack for your vehicle. The crossbars require 4 Inno Flush or Through feet to mount the rack to your roof. You may also need a custom fit kit to mount the crossbars. Built-in T-slots in the tops of the bars let you easily mount carriers and accessories on the rack. Flexible rubber strips in the channels keep out dirt and require no trimming or adjustment. The crossbars are also constructed of strong yet lightweight aluminum so they won't rust.
These lightweight bars have an elliptical shape. This aerodynamic, low-profile design helps to reduce wind noise and drag when you drive. This means you won't need to add a fairing.
Inno Aero crossbars are constructed of sturdy, lightweight aluminum. Internal extrusions add strength and structural rigidity without adding a significant amount of weight. The bars are rustproof so you can leave them on your roof all year long, wherever you go. The sand-blasted powder coat finish resists corrosion, scuffs, and scratches. And the matte black color will look good on any vehicle.
Each crossbar has a channel in the bottom that lets you install Inno feet (sold separately). Slide the channel cover over to reveal a mounting hole for the foot. Clip the foot into the crossbar and then slide it into place along the channel. Built-in bar end stops in the channels will keep the feet from sliding off the ends of the bars.
To complete installation, mount the feet to your roof. This may require a custom fit kit (depending on your application). Attach the locking covers (included with the feet) to secure the roof rack to your vehicle. Locking the covers also secures T-slot-mounted accessories to your crossbars.
This bar has a built-in T-slot that allows you to mount bike racks, watersport carriers, ski racks, and more. The EZ-Slide rubber strip in the bar lets you mount accessories without the need to remove or trim the strip. Just press down on the ends of the flexible strip and slide your accessory's mounting hardware into the T-slot. This strip has a plastic coating so it's easy to slide T-bolts along the channel. The strip runs the full length of the bar, so it helps keep dirt out of the channel when you're not carrying accessories.
You can also attach most clamp-on accessories to the bar, and the rubber strip provides a no-slip cushion for any accessories that rest on it.
These Flush feet help you mount 2 Inno Aero crossbars to your vehicle's factory flush side rails to create a roof rack with a streamlined look. Hand knobs tighten feet in place on rails. Locking covers secure system to roof.
Features:
Specs:
This custom fit kit lets you mount Inno XS300, XS350, XS400, XS450, INTR, or INXR roof rack feet to your vehicle's factory fixed mounting points, flush rails, or tracks. Kit includes all hardware necessary for mounting feet to your roof.
Features:
Specs:
Average Customer Rating: 4.8 out of 5 stars (898 Customer Reviews)
Low-profile, aerodynamic crossbars create an aftermarket roof rack for your vehicle. Aluminum bars have T-slots that let you mount channel-mounted carriers and accessories. Flexible rubber strips in T-slots keep out dirt and won't need trimming. These Flush feet help you mount 2 Inno Aero crossbars to your vehicle's factory flush side rails to create a roof rack with a streamlined look. Hand knobs tighten feet in place on rails. Locking covers secure system to roof. This custom fit kit lets you mount Inno XS300, XS350, XS400, XS450, INTR, or INXR roof rack feet to your vehicle's factory fixed mounting points, flush rails, or tracks. Kit includes all hardware necessary for mounting feet to your roof.Well made. A bit complicated to assemble base, instructions could use some diagrams to help.
I bought this for my 2016 Fiat 500X which has two glass sunroofs, and it fits perfectly! Follow the directions, put the bars where it says to, and your glass will be safe. You can't open the sunroof while this is in place, but hey, at least you can haul gear on your roof without breaking the glass.
Still holding up as well as the day it was installed (Mar'20). I've loaded this system down with a basket full of camping gear and another trip with 3 kayaks and single bike. Everything stayed solid and didn't budge at highway speeds and windy mountain roads.
Great fit, look and service
Good fit and very secure.
Easy install. Works great.
The produce was perfect, easy to put together and strong. And the service and shipping was FAST! Will purchase from here again, no doubt.
etrailer was great to order from! Going to the website makes it easy to see what roof rack will fit your vehicle. Ordering process was a breeze and the fulfillment updates were great. Ordered on the 13th and received it on the 16th so the FREE shipping was super fast. New installs of anything can always be challenging but once I read the the instructions it all went pretty smooth. Installing this Inno Roof Rack onto our 2021 Tacoma TRD Sport was pretty simple and took less than an hours from start to finish. Now we are ready to load up out Thule cargo carrier when we hit the road.
I am writing this review in the context of an owner of an old Yakima roof rack system from many vehicles before the 2021 Hyundai Tucson on which I just mounted four INNO separate sets of components to carry two bikes on top of the Tucson. Note that you need at least three sets of components to have a "base rack" system, including the hooks, in this case the INNO INK680, the INNO INSUT Feet and the INNO INB137 set of crossbars. The feet are rubber coated metal so that they will not mar the paint where they clamp to the edge of the roof just above the doors. The rubber pads are also substantial to provide a slip-proof and paint protecting bottom for the INSUT feet. Read through all the directions for all the components before beginning installation, perhaps even "rehearsing" all the steps before actual installation with tightening everything. The instructions could be clearer, but with practice walking through all the steps they make sense. Once installed, I could grab any part of the completed system and pull upwards, sideways, forwards, and backwards without any play or slack in any of the components. In fact, it was easy to rock the whole car side to side without budging the INNO components at all. Compared to the old Yakima system, the INNO is just as sturdy and substantial if not more so. Just to replace the Yakima "feet" to use my old round Yakima crossbars would have cost more than the total of the three INNO components needed to get the base system. Even better, the INNO system came with included locks to lock the system to the vehicle. Many years ago, the Yakima four lock cylinders were $[XX] extra - probably much more now. So, I think the INNO is at least as sturdy and capable for much less money.
Feels premium and was pretty straight forward to install. I think it looks really good on the 2019 Honda Accord Sport. I plan to pair it with the Inno Wedge 660 cargo box. So far, it seems really well made and has a rubberized texture throughout. I installed it by myself in about 30 minutes without the instructions. It also shipped in only 2 days.
I've been a happy etrailer customer for years. Sales staff helped me pick out the right roof rack setup for my new 2023 Escape that worked with my low-profile rails. 3 separate boxes of pieces but they all came together perfectly. Very happy with my purchase and etrailer customer support! Rack is solid, low wind noise and will work with the accessories I need, kayak carrier and cargo basket.
Got these with the custom fit kit (INK860) and the through feet/stays (INXS250) for my 2014 Ford Fusion Hybrid. Assembly's not difficult, though you do have to work with three different instructions: 1 for the stays/feet (the main install instructions), one for the Crossbars (minimal to do there), and one for the custom fit kit (again, minimal, though this one is crucial as it contains the measurements for the setup).
Things went pretty smoothly. However, when I put it on my roof at the measured distances from the center line, the feet didn't both occupy the rain gutter as they are supposed to. I checked the measurements, and both the front stays were at 21.5" and both back stays were at 21 3/8 " . Since those were the called for measurements, I'm not sure why I didn't fit perfectly. However, they're great and I can't wait to put them to use with my kayak and snowboard and bike. Thanks E-Trailer.
Photos show how great the system looks as well as some of the gaps at the rain gutters. I don't think it's crucial to readjust those. I did try several times but couldn't seem to get them just right.
We bought this along with the INTR - Inno Feet for Square Crossbars. We used this to mount Thule crossbars and a Thule Adventurer cargo box on a 2001 Subaru Forester. Everything fit perfectly. The Inno mounts were completely compatible with the Thule crossbars. The fast and accurate shipping helped avert a crisis before a cross country trip.
I purchased the Inno Rack system and Rhino Rack 581 saddles for my 2007 Mercury Montego. The instructions were easy to follow, and the rack is rock solid. It makes loading and unloading my kayak a breeze. I previously used roof pads and that was ridiculous compared to what this rack does for me now. I am amazed with how quiet with and without the kayak attached is - I don’t hear anything except the very slightest amount of wind with the windows open on the highway. I always have put a one turn twist in the bow and stern straps, but for the rest they’re all straight. I added an extra strap on the rear crossbar that goes behind the rear combing of my cockpit for extra security- but that’s just me. I’ve included a photo to show my setup. Thank you so much Mark S, Becky B, Carol C, and George J. etrailer rocks.
Ask the Experts about this Roof Rack
Do you have a question about this Roof Rack?
Inno Accessories
Fit to this rack on your 2016 Ford Edge
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Roland
1/21/2024
Great. Functional. Finish unmarred. Fasteners stay tight. No wind noise. Very satisfied.