Part Numbers: TLD2127,TLD3109
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.
Features:
If you're looking for the best tie-downs for your camper, frame-mounted is the way to go. The frame is the most solid part of your entire vehicle, so it just makes sense to attach your camper to something that's not going to warp, bend, or twist. Even more importantly, the camper's center of gravity will sit lower and its weight will be spread across the entire bed. This avoids a top-heavy load perched on top of your bed rails that's liable to sway and get pushed around by crosswinds. The camper's not going to shift or slide around while you drive; it's going to stay put, and your truck is going to handle just like it does without a camper.
Quick Tip: If you have a plastic or spray-in bed liner, it's important that you use a rubber mat under the camper to eliminate any sliding or bouncing.
Frame-mounted tie-downs are also a great pick for preserving your truck's good looks. The brackets install on the frame, tucked nearly flush with the underside of the vehicle. Remove the arms from the brackets when you're not hauling your camper, and the brackets will be barely visible.
Completely custom to your vehicle, the tie-downs attach to exisiting holes in your frame so that there's little to no drilling and no need for any modifications. Because they're custom, you'll want to use our in-house application guide to make sure you get the exact right model. The tie-downs you need might be different depending on what type of hitch or other accessories you have.
Once the tie-downs are installed, use a set of turnbuckles (sold separately) to secure the camper to the tie-downs. The shank on each arm has 2 pin holes so you can choose how far out they extend, that way the turnbuckles can reach the anchors on your camper without making contact with your truck. Tighten the turnbuckles to the correct level of tension (not too tight!).
Make sure the anchor points are offset from the tie-downs instead of lined up with them so that they will hold your camper from multiple angles. This is important for keeping your camper from shifting. Two holes in the attachment plate of the tie-downs let you find the best angle for you camper anchors.
Average Customer Rating: 4.7 out of 5 stars (3215 Customer Reviews)
Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there. Get the safest and most comfortable ride while hauling your camper with tie-downs that mount on the frame of your pickup. Great for your truck's looks: remove the arms from the brackets and you'll hardly know that the brackets are there.The drivers rear didn't get built correctly. the hole to put the tie done is missing. I had to drill a hole into the tie down so I could use it. Didn't notice the problem until I went to put the camper on my pickup. The other three are fine.
Forklift tie downs are manufactured to exact fit to existing manufactured frame rail holes. They lined up perfectly and after 6000 miles with camper on board have stayed secure. The only downside, (this is relative to when and ware you use you camper) they will corrode when driving through snow covered roads that have been treated with sand and/or salt. I use an oil based product to protect them corroding.
Easy install, very effective way to keep the camper were it's supposed to be. Just bought a new truck and ordered another set for it. As long as I have a bed mounted camper I will be using this tie down system.
On my 2017 Ram 2500 HD, were easier to install than the front ones because you don't have to put that bolt inside the frame. There is a standoff for a wire on each side that had to be removed, and will need to be secured with a cable tie or something (see attached picture). I had to remove my Trekstep from the driver's side, but I knew I would have to do that, so no big deal. Again, these are very sturdy, thus very heavy, and lighter aluminum tie downs might be considered to reduce weight.
The order arrived earlier than expected and was complete. An excellent job of engineering; all the components worked perfectly with my 2018 Dodge Ram 3500 dually. There was some minor filing that had to be done on 2 of the bracket holes to allow the bolts to fit through; I suspect it was just the powder coating. However no modifications to the truck were required.
The entire project took about 2 hours from start to finish.
I think they’re awesome… put them with the quick gun hold downs and they cant be beat. Keep the camper in place and makes it so much easier.. I own a Dodge Ram Mega cab and they were an easy install, I cant speak to the other truck manufacturers.
Great packing nice turnaround time from order to reviving items cost was competitive only issue one of the sleeves was cut short more photos while installing to come
This products is well made. The transaction was easy and the product arrived as expected. I've been using this product for a year and I have no complaints. It has held up well and does what it was designed to do.
The rear mount arrived this morning, and I immediately went to installation,,,the only thing that could have made things easier would be, if I had a more powerful air wrench to take the bolts out,,,lol.
Looks great! The quality of your product is impressive! And, to think the dealer wanted to charge me $200 to put them on.
I see these as a permanent attachments to my truck,
It was well made and fit perfectly.
Install was easy they work as advertised
Install was easy work as advertised
Seem like a solid well built product. A bit of a pain to install and the instructions could have been more clear and the manual put together better but overall satisfied.
Love the TorkLift Tie-Downs! They are rugged and make loading and unloading much easier than my old basic Tie-Downs.
Bolted right on with no issues. Fit right the first time. Seem to be well over built. Etrailer shipped them off without delays and I have not one complaint.
Very stable easy to set up system
Easy to install and super secure! Made my Lance 1020 feel like its part of my truck. Highly recommended for the juggernaut class truck campers. I’ll never go back to the stake pocket style or bed mount tie downs again.
Cameron
7/13/2022
1 year later, Im still very pleased. Ive gotten many positive comments from people that didnt know they existed and, after talking to me, plan on upgrading themselves.
These camper tie downs have been fantastic! They were easy to install and have made securing my camper a breeze. I really like how easy it is to pull the tie down portion of the brackets out when you aren't carrying the camper. In my opinion this is the only way to secure a truck camper.
Eric A.
7/2/2018
They were great. I ended up getting a different truck and bought another Torklift setup for the new truck. I couldn’t imagine using anything else for securing a truck camper.
The TorkLift frame mounted tiedowns for my truck bed camper mounted perfectly on my 2016 RAM 3500. They are holding my camper on very securely and will be tucked away nicely when I remove the camper for Winter. I plan on making a footstep to slide into the receivers then, so I have much easier access to my high truck bed when I use it to haul firewood. The only suggestion I have is that we cleaned up the punched out pin hole edges with a file, inside the receivers. The sharp ridges would have scratched the hold down assemblies a bit when inserted into the receivers. Maybe an opportunity for a manufacturing process improvement there?
Good service, haven't checked the packaging but everything looks OK from the outside.
Easy to install and work perfect ! No grinding or cutting , just bolt them on. !
They still work great after a year : )
Easy to install whole job front and rear just under 3 hours
These are very well made. They installed easily and fit perfectly. My only concern is that the tie down/turnbuckle attachment hole is slotted and looks potentially weak as a result. I don't know that it's weak, it just looks like making it without the slot would be a lot stronger.
Bruce
11/4/2020
After a year, these have worked out very well. The slotted holes I was concerned about have not been a problem.
Perfect fit, Talked to Will on the phone and h got me the right set-up for my 2015 Dodge Ram 3500. Thanks Will.
Ask the Experts about this Camper Tie-Downs
Do you have a question about this Camper Tie-Downs?
TorkLift Accessories
Fit to this rack on your 2017 Ram 3500
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Chris
9/3/2023
After two winters on the road, this product shows no sign of wear. Im happy with my purchase.