Expert Answers about Toyota Tundra
- Recommended Transmission Cooler For A 2014 Toyota Tundra 4.6 Engine
- When it comes to installing a transmission cooler in your 2014 Toyota Tundra with a 4.6 engine The Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III - Efficient # D13502 is confirmed to fit your vehicle.
The Derale cooler prolongs life of the transmission, improves overall performance, and prevents heat-related failures. The cooler has a furnace-blazed aluminum construction.
I attached a review video link below.
view full answer... - Should New Hardware be Used to Install Curt Trailer Hitch # 13198 on 2007 Toyota Tundra
- Yes, you are correct that new hardware should always be used to install a trailer hitch. Hitch hardware is intended for one-time-use only. Hitch # 13198 uses 1/2-inch as well as M12 and M14 hex bolts.
To order the correct hardware for your Curt hitch simply enter the part # RHK into our search box and then enter the hitch brand and part # 13198. We will then ship you the correct hardware kit for your Tundra.
At right I have linked for you two helpful articles on hitch installation that...
view full answer... - How To Lock The Yakima LongArm Truck Bed Load Extender To The Trailer Hitch Receiver
- Yes, the Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) # Y07235 is exactly what you need in order to lock the Yakima Longarm Truck Bed Load Extender # Y01149. This will simply fit around the anti-rattle bolt that was included with your load extender. I attached a short demonstration video for you.
view full answer... - Parts Needed to Install a Brake Controller on a 2000 Toyota Tundra with Tow Package
- For a 2000 to 2002 Toyota Tundra, you will not be able to use the Hopkins Plug-in Simple Brake Wiring Adapter, # HM47815. As you have stated, it fits 2003 to 2011 models. Of the manufacturers we carry, none offer a brake controller wiring harness that will fit the 2000 Tundra.
If the truck already has a 7-Way trailer connector, you will need to hardwire an installation kit for a brake controller using wire # 10-1-1, and a 20 or 30 amp circuit breaker (see brake controller instructions...
view full answer... - Air Springs For A 2017 Toyota Tundra
- The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88299 are confirmed for your 2017 Toyota Tundra.
The air bags will reduce the strain on your rear suspension, and help increase the safety, and compensate for the uneven loads. It will also help with improving the steering and braking performance of your vehicle.
The springs are constructed of a 2-ply fabric that is reinforced rubber which makes the air springs more durable. The springs have a...
view full answer... - Air Bags or Weight Distribution Hitch for towing with a 2016 Toyota Tundra
- If you have a properly rated and installed weight distribution system you won't have a need for air bags. With your trailer I recommend a system like the Equal-i-zer, part # EQ37100ET, that's rated from 600 to 1,000 pounds.
With the tongue weight of your loaded trailer plus any weight behind the rear axle of your Tunda this system is appropriate for you.
view full answer... - BOLT Hitch Receiver Lock for 2019 Toyota Tundra
- In your 2019 Toyota Tundra you can use BOLT hitch lock # BL7023584. This 5/8-inch diameter pin lock will fit both 2-inch and the 2-1/2-inch hitches and it will code to your ignition key the first time you insert and turn it.
view full answer... - Does Original Prodigy Brake Controller Install in 2007 Toyota Tundra with Harness # 3040-P
- The Prodigy 90185 is the original prodigy and it was repalced by the P2, part # 90885, and then the P3, part # 90195.
We have a video from when we installed the P3 in a 2007 Toyota Tundra using the # 3040-P harness that I've linked for you. The # 3040-P harness fits most Tekonsha controllers including the original Prodigy 90185.
view full answer... - Brake Controller Wiring Harness for a 2015 Toyota Tundra and P2 Brake Controller
- The correct brake controller wiring harness for the P2 # 90885 and your 2015 Toyota Tundra Crew Max is # 3031-P. I have included a link to a video review of this harness for you.
view full answer... - What Parts are Needed to Tow With a 2003 Toyota Tundra
- In addition to a hitch like # 13184, I would recommend ballmount # C45010, as this would put your hitch ball at the most common trailer height.
For a more exact ballmount fit, you can measure from the ground to a point just below your bumper. Then, with the trailer level, measure from the ground to the bottom, flat part of the trailer coupler. The difference between the two measurements would be your required rise or drop. For example, if the measurement to the trailer coupler is...
view full answer... - Looking for Cushioned Ball Mount and 2-5/16 Inch Ball with 10,000 lb Capacity
- For a cushioned ball mount and a 2-5/16 inch trailer ball that has a 10,000 lb weight capacity, I would recommend using the Convert-A-Ball # AMSC2HD Cushioned ball mount you mentioned along with the Curt # C40007. The ball has a 10K capacity, the ball mount has a 14K capacity.
You did not mention the rise or drop you were looking for, I'll link you to our FAQ article that explains how to find out which rise or drop you're needing..
view full answer... - How to Get Industry Standard 5th Wheel Base Rails on a 2022 Toyota Tundra
- To get some standard base rails in the bed of your 2022 Toyota Tundra you need to install the B&W gooseneck hitch and use the Demco adapter rails:
- B&W Custom Underbed Installation Kit # BW46FR
- Demco 5th Wheel Base Rails Adapter # DM6140
This gives you the rails that the Andersen Ultimate Connection # AM3200 will fit to so you can use it with your Tundra.
view full answer... - Can I Use a Different Camera System with the Voyager Pre-Wiring on my 2020 Atlas Trailer
- I don't believe the part that you're seeking is something that's available as a replacement part of any type, however you should be able to remove the Voyager pre-wiring bracket from your 2020 Atlas trailer and leave the bare wiring. With that bare wiring you could install a Furrion system like the # FOS05TASF. If you already had a Furrion camera you could just use the Replacement Shark Fin Camera Mounting Bracket for Furrion Vision S RV Camera Systems - Black - Qty 1 # FRCBRKT-BL to allow...
view full answer... - Trailer Hitch Recommendation For A 2003 Toyota Tundra
- When installing a trailer hitch on your 2003 Toyota Tundra V6 The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # 75105 will work for you if you do not have a factory towable bumper. The factory towable bumper would be attached to the bumper and you could slide a hitch ball into it if you had it. The hitch has a gross towing weight up to 5,000 pounds and has a tongue weight up to 500 pounds. I would check your vehicle's manual to find out what the correct...
view full answer... - Which Part to Add Explorer Rails to Pace Edwards Jackrabbit Tonneau on 2010 Toyota Tundra
- I have a solution for you, but the # 311-TE5117 are not Explorer rails designed to fit on a 2010 Toyota Tundra. For your 2010 Tundra you've got the # 311-JRT5379, so you will need the # PE45GJ rail kit to add Explorer rails to your tonneau.
view full answer... - Parts Needed to Flat Tow a 2002 Toyota Tundra Behind a Motor Home
- From the research I did it may be possible to flat tow a 2002 Toyota Tundra behind a motor home depending on how it is equipped, What you will need to do is consult the owners manual for your truck to determine if it can be flat towed and if so what the procedure is and what additional parts may be needed.
If after you consult the owners manual and determine that you can flat tow the truck, there are 5 items you will need: base plates, tow bar, safety cables, lighting, and supplemental...
view full answer... - Parts Needed to Install a 7-Way Trailer Connector on a 2001 Toyota Tundra With Existing 4-Way
- Your best option is to install our Universal 7-Way and 4-Way Installation Kit, part # ETBC7. There are no plug-in style 7-way trailer connectors that will replace the Tow Ready harness on your truck, but the ETBC7 will use your existing 4-way and provide the additional hardware and wiring needed to have a fully functioning 7-way trailer connector. I attached an installation video on a 2002 Toyota Tundra to give you an idea of what will be involved with the installation. The installation...
view full answer... - Replacement OEM BOLT Lock for Extang EnCore Hard Tonneau Cover on 2018 Toyota Tundra
- If you have an Extang Encore Hard cover then the Replacement OEM BOLT Lock # EX62CR is the part you're looking for. This is the correct BOLT lock for the EnCore that fits on Toyota Tundra models.
view full answer... - Longest Available M6 Bolt for Thule Cargo Box
- The longest Thule M6 bolt I'm aware of is the Replacement M6 x 92 T-Bolt for Thule Criterium Roof Mounted Bike Carrier # 853-6511, which is 92mm long and might work for your application.
view full answer... - Adding a 7-Way Trailer Connector to a 2013 Toyota Tundra with 4-Way Connector
- The brake controller I recommend for your 2013 Toyota Tundra is the Prodigy P3, part # 90195. It's our top selling brake controller because of how easy it is to use and how reliable it is.
Since you have a factory 4-way trailer connector on your truck you might have a port under the dash to plug in a brake controller. Look up behind the emergency brake pedal near the kick panel for a white connector. It's pointed out in the picture I attached and you can see it in the video I've linked...
view full answer...
Go To Results