The etrailer Trailer Hitch Receiver # e98864 uses M12-1.25 x 35mm hex bolts. I have attached an installation video along with the written instructions below for your reference. view full answer...
The Curt hitch # C13524 that you have referenced is a good choice. It has more than enough capacity to safely tow the boat and trailer. However, before doing any towing you will want to consult the vehicle owners manual to determine what the vehicles towing capacities are and not exceed them. Even if the hitch is rated higher you still must go by the lowest rating.
I also recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage... view full answer...
The TorkLift GlowStep Revolution Scissor Step # TLA8004 does include the hardware to install the mounting base on the frame of your Grand Design 5th wheel. The hardware is shown in the linked photo. The included video highlights the step's features and shows the installation. The specific RV shown has vertical step mounting studs so it also required Vertical Stud Adapter Bracket Item # TLA8022. view full answer...
The currently listed price is for two running boards, these are sold as a pair or set of two. One kit contains two running boards, mounting hardware, and instructions. view full answer...
I went out to our warehouse to check the Replacement Master Parts Bag for X-Cargo Box, # TH04870, and I can confirm that there are installation instructions included in the parts kit. view full answer...
With the tire size 235/55 that you included, I cannot confirm for sure if the Thule Spare Me 2 Bike Rack # TH963PRO will fit your non-standard spare tire for sure. This is because I need the last number of the tire size (the wheel's diameter). However, I can confidently say the rack will most likely fit your wheel's diameter because the maximum diameter that is compatible with the Spare Me 2 is 33 inches (which is a pretty large tire). Although, I can 100% confirm that the 235mm width... view full answer...
The Electric Trailer Brake Kit - 7" - Left and Right Hand Assemblies # AKEBRK-2 are just the electric drum brakes for 2,000lb axles and do not include drums. They are designed for a 4 bolt mounting flange bolt pattern and fit most standard hub-and-drum assemblies, including Dexter, Lippert (LCI), and AL-KO. They fit a wheel size of 10", 12", or 13".
You'll want to match the brake flange pattern, axle capacity, and hub size when considering what options will fit your application.
Since... view full answer...
If your key needs to be in the ACC position so that the steering wheel is unlocked you would need to have the battery disconnected so that it wouldn't drain.
I'd recommend using a Roadmaster Automatic Battery Disconnect, part # RM-766. The disconnect would allow you to 'disconnect' the battery with a flip of a switch. When the battery is disconnected, the taillight circuit from the RV will maintain the battery in the towed vehicle (you'll need to leave the running lights in the RV on... view full answer...
You are correct that there is only one replacement cradle included per package. These replacement cradle pads are intended for use on the Swagman Original Series Hitch Mounted bike carriers that were produced from 1999 and newer. view full answer...
The Curt Trailer Hitch Receiver part # C13416 which is a fit for a 2019 Toyota RAV4 does not come with trailer wiring as not all those who purchase a hitch want to tow i.e. bike racks and cargo carriers. That said, we do have the correct trailer wiring harnesses available, the Curt T-Connector Vehicle Wiring Harness part # C56434 is what I recommend. In order to complete your towing setup you'll also need the Curt Towing Starter Kit part # C45534. view full answer...
Yes it does, the part # ETBC6 when installed will give your 2008 Toyota Rav4 a fully functional 6-way and 4-way so it should work perfectly for you.
I attached a set of installation instructions for you to check out. view full answer...
We do have what you need but the Firestone Coil-Rite Air Helper Springs # F4174 does not include the bracket to install on the hitch. You would need Replacement Inflation Valve Bracket for Firestone Air Command Compressor Systems # FWR17607560. Also Firestone Union Tee for 1/4" Tubing # F3025-1. view full answer...
Yes, the Stinger Load Assist # MPG350 for the Malone SeaWing Kayak Carrier # MPG107MD does include the pads on the load assist as seen in the images on our website. view full answer...
The replacement Rock Tamers mud flap you referenced, part # ERTO22 is sold individually. If you needed two of them, you'd need to order two of that part number. view full answer...
The Curt Trailer Hitch Receiver part # C13416 which is a fit for your 2019 Toyota RAV4 does come with all the hardware that you will need for instillation. I have attached an install photo of the trailer hitch for you as well. I also recommend you use the Curt Rubber Tube Cover part # C22272 to keep the inside of the receiver tube protected while not in use. view full answer...
The Optronics # STL572RB Sealed LED Stop/Turn/Tail Light is sold as a single piece, not a pair.
For complete installation you will require the corresponding rubber grommet, part # a70gb, which provides protection from mechanical stress, and the mounting bracket, part # BK70BB. Please note that in an existing 2 inch by 6-11/16 inch opening the grommet can be used to mount the light; if not the bracket can be used.
You will also need the 3-wire pigtail lead in either the straight or right-angle... view full answer...
The SmartPlug RV Power Cord - 125/250V - 50 Amp - 30' Item # SM86FR does not come with the smart plug RV receptacle.
If you need the receptacle we offer the SmartPlug Replacement RV Power Inlet - 50 Amp - Gray Item # SM29FR view full answer...
Both the Curt Hidden Cross Tube # C13406 and Visible Cross Tube # C13149 for your 2016 Toyota RAV4 include the M12x1.25 40mm long CL10.9 bolts needed to attach to your frame. You will not need to reuse or provide additional hardware to install these receivers. It is recommended to use a Brush # 814092 with cleaner to remove any dirt built up inside the threads. view full answer...
The original Rack and Roll trailers had incandescent lights but now the lights are LEDs. The switch started in about October of 2010. I have included a link to a video review of Rack and Roll trailer # Y08106 for you. view full answer...