The Furrion Vision S Wireless RV Backup Camera System part # FOS5TASF will need to be used with its own monitor. It is not compatible with a factory in-dash monitor nor is there a system that I am aware of that allows for this. If the trailer is pre-wired for a Furrion Wireless RV Backup Camera System then this will be your only option. view full answer...
The SumoSprings Trailer Helper Springs w/ Line Relocation Bracket # SS33HR are going to install onto your 2022 Grand Design compressed so they will have a little bit of space between the frame and the axle but this is normal. view full answer...
Since the Zippered Cover for Lend-a-Hand RV Grab Handles # SC83VR is tan instead of the original black it will naturally run a little cooler than your original black foam handle.
With that being said, if you don't have any shade on the handle and you're in a really hot climate you'll want to either look for a white handle cover (which we don't have), or maybe try covering your handle up with something like a white towel while you're away to help mitigate the amount of sun that's beating... view full answer...
As long as the surface where the brake magnet rides is in good shape with no damage, and there are no signs of excessive heat like discoloration or cracks in the surface where the brake pads ride, there is really no advantage or need to replace your drums.
If you do see any cracks, discoloration, or grooves on the surface where the brake magnet or brake pads ride you will need to replace the hub and drum assembly.
If you end up needing a replacement hub and drum assembly, just let me... view full answer...
The correct foot pounds of torque for the Westlake # LHAWSO513B will depend on which size lug bolt you have. As this is a 16 inch aluminum wheel, I have the torque ratings listed below:
1/2 inch coned lug nut - 90 to 100 ft-lbs
9/16 inch coned lug nut - 120 to 140 ft-lbs view full answer...
Due to the design of the Lippert Center Point by Trailair Air-Ride Suspension Upgrade # LC1565391 installs there isn't a way to install it without adding the 2 inches of height you mentioned. view full answer...
Thanks for the photo, and if there isn't the needed clearance, you need to get the slide topper the next size down that won't interfere. For example, if you normally would get the 79 inch wide Solera RV Slide-Out Awning # LCV000168105, but it was a couple of inches too wide, you would go with the next size down, which is the 73 inch Solera RV Slide-Out Awning # LCV000165063.
This may not cover your full slide-out, but it would still cover the majority, and would be the only way for installation... view full answer...
The Solera RV Slide-Out Awning - 13'7" Wide - 48" Projection - Black # LCV000168110 is a complete kit including the rail extrusion. It doesn't have a specified pitch for the rise over run as you described as it simply has a minimum placement of the rail being at 3 inches over the slide. There is a range of anywhere between the 3 to 7 inches and some trailers come with a rail extrusion already attached for you to utilize. If you use the 3 inch minimum for the rail extrusion, then it will... view full answer...
In regards to the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part # LC675817, the middle and rear jacks require at least 6" of space on the frame for mounting. If you don't have this much space then I can see trimming the brackets slightly and then welding them as being an option. That said, I can't really recommend modifications so in the end it will be up to the discretion of the installer to determine compatibility. view full answer...
I have linked the installation instructions for the Kodiak Disc Brake Kit # K2R526D below. This link will take you to Dexter's website page for Kodiak brakes. Simply scroll down to the link for installation instructions where you will find all the updated torque specifications for these. view full answer...
The JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ 58" or More Between Landing Gear # LC191023 installs by bolting on to the trailer's frame and the existing stabilizer legs, and there is no welding required. As long as you've got a little bit of mechanical knowledge, the installation really is fairly straightforward. You're likely going to need to drill holes in the frame members on your trailer to complete the installation, which should be the most labor intensive part of the... view full answer...
I consulted the owner's manual for your Reese Sidewinder, and they mention that you are going to need to apply grease # L11354 to the surface on both sides of the wedge, around the kingpin, and the skid plate surface, which would require you to remove the 4 bolts to remove the turret from the pin box.
If there is any old grease you are going to want to clean off the old grease and apply new grease.
I have also attached a couple of instructional images for you to reference as well. view full answer...
Yes the magnets of the Easy-Hitch Light-Up, Telescoping Hitch Aligner # JE00600 are strong enough to attach to the king pin and hang upside down. view full answer...
When applying the Alpha Systems Patch Kit for SuperFlex RV Roof Membranes - Almond - 3' x 2'
Item # AL84CV to the roof of your 2019 Grand Design Reflection Fifth Wheel, you will need to hold the patch material in one hand while heating the area that is to be repaired. As the material is being heated, apply the patch material in a reverse peel motion.
Here is the repair procedure from Lippert:
1. Identify the size of the area and thoroughly clean with mild soap and water.
2. Cut an oval... view full answer...
The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set # LC358590 has 4 35-amp fuses located on the controller.
Attched is a complete wiring diagram for you to check out. view full answer...