Your 2021 Hyundai Santa Fe will need a 7-way to accomplish this so you'll have two options; if you have the factory tow package you'll have a connector that your 4-pole wiring is connected to that you can swap over to the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package # C68JR or if you do not then you'll need the # ETBC7 and will have to splice in some of the wiring.
If you have to use the # ETBC7 you'll run a wire to the battery and another wire into the cab to connect... view full answer...
To install 7-way on the back of your 2023 Hyundai Santa Fe you'll just need the Tekonsha # TK44ZR, which is going to come with everything you need besides the tools needed to install it. I've attached a picture from the wiring diagram below that shows where the wires will connect to for the inside of the 7-way. When looking at the back of the 7-way your black 12v power wire will be to the center left. view full answer...
While the Curt Trailer Hitch Receiver # C13240 will fit your 2021 Hyundai Tucson you will need either the Curt # C34ER or our etrailer # e28AR receiver for your 2023 Hyundai Santa Fe hybrid. Personally I prefer our etrailer # e28AR receiver with the matte black finish. It is also manufactured by Curt so you get the quality you expect with Curt.
The Upgraded Heavy Duty ModuLite Circuit Protected Vehicle Wiring Harness # C59496 will allow you to wire a 4-way flat to your Santa Fe. This... view full answer...
The # S64650 bike rack does not have vehicle specific fits, but it does offer a clearance of 10-1/2 inches from the hitch pin hole to the first wheel loop on the rack. You will need to take a measurement to determine whether it would offer enough clearance to work on your 2009 Hyundai Santa Fe.
Measure from your hitch pin hole to a point past your bumper and anything else that might get in the way of the rack or bikes. If this measurement is less than 10-1/2 inches, the rack would work... view full answer...
Yes, the Curt Trailer Hitch Receiver part # C13505 which is an excellent bolt-on, assembled in USA option for a 2005 Hyundai Santa Fe will fit models with a full size spare tire. The spare will need to be lowered for installation but it can be raised back up into position when done.
If you'll be towing then don't forget the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118473 and the etrailer Ball Mount part # 989899. view full answer...
The Titan Chain Cable Snow Tire Chains # TC2019 will fit 235/55-19 tires and according to the online manual for your 2020 Hyundai Santa Fe it's okay to install chains on the front and rear tires on AWD models (only front tires for 2WD models).
Please note that cable chains don't provide much traction and are basically only good for staying legal where chains are required. If you're wanting chains to actually help with traction then I recommend tossing the cable chains and upgrading to... view full answer...
The best trailer hitch option for the 2019 Hyundai Santa Fe is the Curt Class III Round Tube Receiver Hitch part # C13195 which is going to provide you with about 250 more lbs of tongue weight capacity compared to the other option. I have attached an installation video for your reference. It is a good idea to check your owner's manual for the specific weight that you can tow according to the manufacturer and stick to that.
For the wiring, I recommend Curt T-Connector Vehicle Wiring Harness... view full answer...
Yes, the Draw-Tite 2-inch hitch # 75776 is a confirmed fit on your 2018 Hyundai Santa Fe XL. It also fits other versions including the SE, GLS and Limited. The included photo shows the clean appearance of the hitch after installation.
Hitch # 75776 bolts on using the included hardware kit and no drilling is required. Written instructions (that list the tools needed for installation), a helpful article and a complete install video are included for you to guide your hitch installation.
I... view full answer...
We have the dimensions on the main unit and control knob for the Redarc Tow-Pro Elite # RED44FR, but unfortunately we have not had the opportunity yet to install one of these on a 2016 Hyundai Santa Fe Sport 2.0 FWD so I don't have a way to confirm if it would fit on my end.
The main unit measures 3-3/8" long x 3-15/16" wide x 1-1/8" tall and the control knob measures 2-3/8" long x 3/4" wide x 7/8" tall. I have linked some photos with these dimensions marked so you can take some measurements... view full answer...
Yes, the etrailer.com Trailer Hitch Receiver # E98841 will fit your 2017 Santa Fe Sport 2.0T Ultimate. I have attached an installation video that you can use as a reference.
If you are looking for a bike rack then I highly recommend the Kuat NV 2.0 Base # BA22B because it is not only a great looking bike rack but it also has easy-to-use features like the foot pedal for tilting and folding the rack. You also have the ability to add some upgrades like the add-on # BA02B to carry up to 4... view full answer...
The 2013 and 2016 model years of the Hyundai Santa Fe are both part of this vehicle's third generation. They share common fits for hitches and trailer wiring for the specific versions offered.
I have linked for you two pages, one each for the wiring harness fits for each of the two model years. As you compare the products shown for each you'll see that the same items will fit specific versions of both model years.
For the 2016 Sport, SE and Limited versions WITH the factory tow package... view full answer...
Hollywood Racks TRS 2 Bike Platform Rack for E-Bikes # HR3500E will work with your fenders but it does take a little bit more finesse to slide under the wheel. Make sure there is at least 1-1/2 inches between your tire and the fender. If not you may be better off going with a frame hook bike rack like the Swagman Dispatch 2 # S44FR. This rack doesn't use the wheel hooks like the TRS 2 and I highly recommend the Swagman Dispatch for your situation. It will be a much easier rack to use with... view full answer...
The Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL is designed to be a replacement handle for Landing Gear Set # RVLG-8HDL. Replacement handles attach to landing gear in a number of ways so they need to be matched with their manufacturer. For example, # LC119226 is a replacement manual crank for Lippert Components landing gear.
Once you take a look at the manufacturer of your landing gear, just go to the link I've attached which has each of our available... view full answer...
For your 2014 Hyundai Santa Fe Sport with factory roof rails order parts # RRVA137B-2 and # RRSX032.
Since all roof racks make some amount of noise when you drive, most owners tend to keep a sunroof closed after a roof rack is installed. If you install carriers for bikes, kayaks or luggage on the roof rack these items' mounting hardware may interfere with the sunroof even if the roof rack itself does not. Those other carriers will also make their own noise!
The general wisdom is to keep... view full answer...
To install the Curt Echo # C51180 on your 2019 Hyundai Santa Fe, you will need to start with a 4 flat harness like the Curt # CU94FR. Once that is installed, you will need the 7-Way RV Upgrade Kit for Trailer Brake Controller Installation # ETBC7L. This will get the needed power to the # C51180.
The only other part I suggest is the # 18136 bracket. This allows for easy installation of the # ETBC7L onto the Curt Hitch # C13195. view full answer...
I reached out to Draw-Tite directly and confirmed that the Draw-Tite Trailer Hitch Receiver # 75776
is correct for your 2018 Hyundai Santa Fe SE XL. I attached the installation video for the Draw-Tite Trailer Hitch Receiver # 75776 on a 2018 Santa Fe for you to take a look at.
If you are planning on towing a trailer in the future I recommend adding Vehicle Wiring Harness Kit w/ 4-Pole Trailer Connector and Installation Kit # C59236 for your Santa Fe if it does not have the factory tow... view full answer...
The claws in your picture look similar to the Replacement Large Claw Assembly for Yakima Railgrab item # Y80144. I have attached a graph showing what type of Yakima claws fit what kind of roof rack to assist you in matching up your rails to the correct claws. I have linked our selection of replacement claws.
Yakima also makes a roof rack system for your 2019 Hyundai Sante Fe the roof rack Includes:
Yakima JetStream Crossbars - Aluminum - Black - 50" Long - Qty 2 Item # Y00425
BaseLine... view full answer...
Unfortunately, the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2", part # 75532, that is compatible with your 2007 Hyundai Veracruz is not compatible with your 2009 Hyundai Santa Fe.
The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2", part # 75471, will fit your 2009 Hyundai Santa Fe. It has a maximum tongue weight of 525 lbs and gross maximum tongue weight of 3,500 lbs.
I have included a product description link and an installation... view full answer...
What you have been told used to be true until the creation of the Hollywood Racks Over-the-Top rack # HRF2-3. This rack has an additional upper arm piece that moves the top straps up and over that spoiler so no weight is put on it (since the spoiler is not meant to support weight). I have included a link to a video that shows how it works.
If you will be carrying any bikes that do not have a top frame bar that goes straight across (like a typical men's bike would) then I recommend using... view full answer...
Yes, you are correct the etrailer Hitch item # e28AR does indeed fit the 2023 Hyundai Santa Fe. This hitch is custom fit and bolts to your Hyundai with included hardware.
I really like the etrailer hitch because the crosstube mounts behind your rear bumper cover. This leaves only the 2" x 2" receiver visible which gives a better look and also significantly improves your ground clearance.
The etrailer Hitch item # e28AR is a class III hitch, with a 2" receiver, and it weighs 34 lbs. It... view full answer...
Go To Results