Yes the Adco SFS AquaShed part # 290-52241 will allow you to have access to the rear door of your RV as it has a three zipper off sections. A section for the front, middle, and rear. view full answer...
The Fan-Tastic Vent Cover FVU1500GR has been phased out so you would need to use the Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover - 23" x 19.5" x 10.25" - Black # FVU1500BL in its place. If you don't already have the mounting brackets in place and will be using the ones included in the kit then I recommend also picking up some self-leveling sealant # 34427034145-1 for proper waterproofing.
If you'd prefer more light passing through into the trailer then I recommend going with the... view full answer...
The mounting dimensions for the Lippert Components High-Speed Power Stabilizer Jack # LC298707 are 68-11/16" from center-hole to center-hole.
Since this stabilizer jack is a universal fit the only way to know if it is compatible is to make sure that you have a frame width that is compatible with the mounting center locations.
I have linked the instructions to this page for you to reference. view full answer...
The 2017 Forest River R-Pod could use either the Axle Riser Kit - Single Diamond Torsion Axle part # LC270682 or Axle Riser Kit - Single Square Torsion Axle part # LC382741. It all comes down to what was installed at the factory which could have been either. Unfortunately, we don't have a way to look up exactly what you have so you'd need to physically check for yourself whether you have a diamond or square axle. view full answer...
Since your unit is hardwired you would have to cut the connector off of the Advent Air Replacement RV Air Conditioner # ACDOM135 in order to hardwire it into your system. Doing this will void your manufacturer warranty so I do not recommend it and instead recommend just replacing the system entirely with one like the Furrion Chill HE RV Air Conditioner System - Manual - 13,500 Btu - White # FR52PR or # FR95PV for wall mounted thermostat.
If you don't care about the warranty and are will... view full answer...
The Classic Accessories Deluxe PolyPro III HD Cover for R Pod Trailer # CA80199 you linked to does come with a zippered entry door as well as a rear panel to offer you access to your trailer's doors. The price is just a reflection of the amount of material used. R-Pods are typically smaller and require less material than the standard travel trailer. You'll see the same for pop-up campers versus R-Pods. view full answer...
Yes, your 2021 Forest River R-Pod 202 is absolutely compatible with the Ultra-Fab stabilizers, which are the following part:
- Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705
This stabilizer has the proper width and more than enough capacity to work well with your travel trailer, and will give you a very easy way to level it out because of its independent motors. They operate independently, so even if you are on uneven ground you will be able to level and stabilize... view full answer...
Lippert's 4,400 lb axles like what you have use the same bearings as 3,500 lb axles so the correct replacement bearing kit is the following:
- Bearing Kit # BK2-100 view full answer...
The covers for your 2016 Forest River R-Pod 177 are designed to take into account the different accessories that are on your roof, including your air conditioner and antenna, which will be covered and still be the proper length.
For your 2016 RP-177 the best cover is the Adco SFS AquaShed Cover for Travel Trailer # 290-52239. view full answer...
Yes the Go Power Overlander Solar Charging System with Digital Solar Controller # 34282181 would be a really great choice to charge the 12 volt battery of your 2020 Forest River RP195. Since your Forest River is pre-wired it would have wiring ran to the battery already. view full answer...
Yes, you'll need the Adapter Wiring Kit part # ACCOLKIT in order to use the Advent Air RV Air Conditioner part # ACM135 on your trailer with the existing controls. If you opt for the Advent Air RV Air Conditioner System part # ADV94FR, you'll want to keep the old wall mount controller for the heater. view full answer...
The etrailer eDream RV Mattress # e94FR that you mentioned does not fold in half, however these mattresses are pliable and will work just fine in a Murphy bed.
Murphy bed's typically are designed to accommodate mattresses that are up to 12" thick, and since this mattress is 9" thick, this'll work fine. view full answer...
The Torflex Lift Kit # K71-724-02 is designed to be used with #11 Dexter Torsion axles. To verify this is what you have under your 2020 Forest River R-Pod RP195 you can verify with the label on the axle tube or measure the bolt pattern for the axles. The bolts for the axle connection to the frame will be spaced 9" on center. This will give you a 2-7/8" lift for your R-Pod. If you have a different axle or measurement please let me know so I can confirm the correct kit for you. view full answer...
While we don't have just the grey pad of the Yakima Raptor Roof Mounted Bike Rack we do have the entire jaw pad assembly with the part # 8820182 instead which would be your best option. view full answer...
I have a solution for you.
You are going to want the Adco Olefin HD All-Climate + Wind RV Cover for Travel Trailer - Up to 22' Long - Gray
# AD47ZR. It offers the best protection for a stored RV. This will Fit RVs from 20-22 feet long.
The Adco SFS AquaShed Cover for Travel Trailer - Up to 18' - Long - Gray # 290-52239 is not long enough and only fits RVs up to 18 feet long. view full answer...
Yes, you can remove the bracket bolts off of the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500lbs - Qty 1 # TJSC-24 and attach it to the brackets you already have on your camper. I actually end up recommending doing this quite a bit because RV manufacturers love to use odd sizes and most people would prefer to not add more holes in their campers when they can just reuse their current bolt holes. view full answer...
Yes, RV storage covers like the Classic Accessories PolyPro III Deluxe RV Cover for R-Pod Trailers # CA80-197-171001-00 do take into account for AC units and other accessories being on the roof. I was actually just looking at a similar cover from Classic Accessories that we used on the HYK trailer we have here and it was surprisingly thicker than I was expecting.
This specific cover is for trailers measuring 17' in length from the front of the rear bumper to the tip of the trailer tongue.... view full answer...
Thank you for the all the info, I was able to determine that you have a Rhino Box bolt pattern so the correct replacement would be the Curt Flex Air 5th Wheel Pin Box # LC65VR for your 2023 Grand Design Momentum 381MS. The Rhino box is quite a disappointment to most trailer owners so this new Flex Air will sit a bit lower and should help raise the nose of your trailer up to ride more level. view full answer...
Trailer hitches are not designed as custom fits for any RV like your 2017 R-Pod, but we can narrow down your choices. In order to choose which hitch is correct, you need to measure the frame of your trailer, which is going to let you know the exact hitch you need. So long as your R-Pod is a box frame, C-channel frame, or I-beam frame you will need one of the following two hitches, depending on the width of your frame:
- 18" to 51" Wide: Adjustable Width Trailer Hitch Receiver for RVs #... view full answer...