The Reese Low-Profile 5th Wheel Trailer Hitch - Dual Jaw - 30,000lbs # RP30054 was designed to be welded or bolted to directly to the frame of cab-and-chassis style trucks so you will be able to attach it to your 1988 Ford Super Duty 7.3L Cab-and-Chassis. I spoke with a Reese technician and they stated you may have to weld a plate to the frame first and then weld or bolt the hitch to the plate.
You'll find the installation instructions attached below. view full answer...
After reaching out to Curt about your 2007 Ford F-450 Cab and Chassis you can use the Class IV 2 Inch trailer hitch receiver # C14048. view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver # 65049 is confirmed to fit your 2020 Ford F-450 cab and chassis. It has different mounting points than the Draw-Tite Receiver # 65076 that you were looking at.
I recommend keeping either a Cover # 63080 or Step # WT81BS1XL in the receiver to eliminate the whistle from the wind front receivers will often create. The step is great as it allows you to easily access under the hood if you do your own service work or run into issues on the road. view full answer...
Yes, the Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 65049 is confirmed to fit your 2015 Ford E-450. As you can see in the attached demonstration video, installation is simple and it does not require welding. view full answer...
The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford # 3034-P is the correct fit for the harness you have on your 2018 Ford E-450 Chassis. This will work well for your motorhome.
The # 22292 is a fit for the F-series trucks but not the E-series van chassis. view full answer...
If by RV you are referring to a motorhome then yes, you can use the Swagman Titan 2 Bike Carrier # S63400 with your motorhome. The Titan has a built-in cable lock. To add an anti-rattle hitch lock to this bike rack you need the # S64029.
Some people do refer to their trailer as an RV (usually bigger trailers). If this is the case then you will need to use a bike rack that has been tested and approved for the extra movement and stress that is at the rear of a trailer.
For a similarly... view full answer...
We do not at this time have a custom-fit gooseneck hitch for your 2018 Ford F-450 cab and chassis but we do have hitch fabrication parts like Curt # C65500 which has a rating up to 30K depending on the installation. This hitch does require under-bed reinforcement to reach its maximum capacity. view full answer...
You will need to determine if your 2021 Ford F-450 is a Super Duty model or a cab and chassis model. If you are unsure you can check the tag inside your door as a cab and chassis will state "Incomplete Vehicle Manufactured By Ford" on the tag. If you have this tag you will want the Air Lift LoadLifter 5000 Air Helper Springs # AL57345. Otherwise you will want the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs # AL57577 for the Super Duty model.
Both these kits are easily controlled... view full answer...
The bike carrier I recommend to carry your Electric bikes is the Hollywood Racks Sport Rider Bike Rack for 2 Electric Bikes # HLY84FR. This bike rack has a weight capacity of 80 lbs per bike. The rack tilts away from the vehicle to give you access to the hatch area and is also rated for use on the back of motorhomes, not all bike racks have that rating. I have attached a video reviewing the Sport Rider SE Bike Rack for 2 Electric Bikes.
If you are needing hitches for the 2004 Ford F-450... view full answer...
I have listed the correct sway bars for your 2021 Entegra Odyssey 26D Class C motorhome below.
Front Anti-Sway Bar
- Roadmaster Front Anti-Sway Bar # RM-1139-176
Rear Anit-Sway Bar
- Roadmaster Rear Anti-Sway Bar # RM-1139-147
I was able to verify these are the correct fit for your Class C motorhome on a Ford E-450 Chassis with the manufacturer. view full answer...
The Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter for Recessed Ball # DM8550046 sits in a fixed location right above the gooseneck hitch ball so you'll need to measure from where your gooseneck hitch ball sits to where the 5th wheel body starts to determine if a setup like this will work with your 2016 Ford F-450.
An easy way to test clearance is to back your truck up so the gooseneck hitch ball is directly under the king pin on the trailer.
Unfortunately flat bed trucks are... view full answer...
Yes it will; according to the manufacturer, Buyers Products, your Ford F-450 cab and chassis will allow you to mount, without drilling, the Buyers Products hitch plate bumper, which is the following part number:
- Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver # 3371809055 view full answer...
The Tekonsha Primus IQ Trailer Brake Controller # TK90160 is a great choice for sending power to and controlling your trailer's brakes from your RV. It is a proportional brake controller which means it will activate the trailer's brakes at the same time and with the same intensity that you apply to them in your RV. This is compatible with the Ford F-53 chassis.
I recommend adding the Tekonsha Plug-In Wiring Adapter # 3035-P for easy installation. Because you have the built-in connector... view full answer...
The correct sway bars for your 1999 Fleetwood Jamboree 29L Class C Motorhome on a Ford E-450 chassis are the Roadmaster Front Anti-Sway Bar # RM-1139-115 and the Roadmaster Rear Anti-Sway Bar # RM-1139-147.
For the steering stabilizer you'll need the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets # RM47MR. view full answer...
The Adco Olefin HD RV Cover # AD34ZR is a great option for your 2018 Jayco 26XD Class C RV. This cover works best for long-term storage in all climates. Heavy-duty fabric protects against rain, dirt, wind, and sun. The contoured fit will match shape of your RV and secure with cinch ropes and straps for nice, snug fit. view full answer...
Buyers Products confirms that the # 3371809030B is a fit for 1999+ F350,450 and 550 Cab/Chassis trucks.
Cab and Chassis trucks, including the 2001 Ford F-450 Cab/Chassis model use a 34 inch frame spread, which is exactly what the Buyers Products # 3371809030B Hitch Plate for Pintle Mounting is designed for. It'll work very well on your truck.
If you click the provided link, you can see a product description video for the # 3371809030B hitch plate. view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver # 65053 is confirmed to fit the 2015-2021 E-Series Cutaway E-450. As of July 2023, we have not had a chance to test this to confirm if it will fit the 2022 (your 2023 Conquest would be built on the 2022 model). Draw-Tite also does not list this as a fit, but they're further behind than we are since they only show it up through 2017. However, given the amount of other parts that carried over to the 2022, it is very likely it will work.
What... view full answer...
To replace your JVR9000 I recommend the Jensen RV Stereo - Double DIN - AUX/USB, Bluetooth # JWM40. It has slightly different dimensions that can be easily fixed using a dash plate. This won't have a monitor to watch your video feeds from so you'll need the Voyager RV LCD Observation Monitor # VO34FR to still use your Voyager camera system.
If you need a mount for your new monitor you can use the # VOSHD6MNT.
Since this isn't a direct plug-and-play replacement I've included the wiring... view full answer...
The correct front mount trailer hitch for a 2016 Freedom Elite Motorhome on Ford E-450 Cutaway Chassis is the Draw-Tite Front Mount Trailer Hitch Receiver part # 65053. This is the only available option for this chassis.
It seems like you were looking at front mount hitches for a F-Series and not the E-Series which is where the confusion lies. view full answer...
For a 2022 Entegra Odyssey 24B on a Ford E-450 chassis you'll need the Roadmaster Front Anti-Sway Bar # RM-1139-176 and the Roadmaster Rear Anti-Sway Bar # RM-1139-147.
If you're also looking for a steering stabilizer to help improve your motorhome's handling then you'll want the Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets # RM47MR. view full answer...