For your application I recommend using the Draw-Tite Class III Trailer Hitch # DT78MR because when we installed it on a 2020 Jeep Wrangler Unlimited we found that from the center of the hitch pin hole to the rear edge of the bumper was 1". The Yakima FullSwing # Y02465 has a max distance of 6-3/4" from the center of the hitch pin hole to the furthest edge of the tire.
Since the Sahara has a different bumper than the normal Wrangler you'll likely need the RockyMounts Extender # RKY10008... view full answer...
I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part # 336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few dimensions on the above in hopes these were what you were looking for. If it is not please try to further clarify this for me and I would be happy to remeasure this for you.
I have attached a photo below with the dimensions I think you are looking... view full answer...
Hub faces are designed to be in the exact same position. If the etrailer.com hub part # AKHD-655-35-EZ-K will fit your trailer spindle it will have a hub face dimension that will be the exact same as what your setup currently has.
For a right hand side assembly we have the part # AKEBRK-35R-SA and then for the left hand side part # AKEBRK-35L-SA. view full answer...
The capacity of the Superwinch part # 1120210 is 2,000 lbs. We have it in a facet category with other winches that have weight capacities that range from 1,000 to 2,000 lbs. Sorry for the confusion! view full answer...
All weight distribution/sway control systems such as the Equal-i-zer 4-Point # EQ37060ET operate over a range of trailer tongue weight (TW). Ideally your actual TW will fall near the middle of the system's operating range. If the fully-loaded TWs of both trailers happen to fall within the systems operating range, in the case of this system 200- to 800-lbs, then the one system would work for both trailers. The different vehicles matter only in terms of their heights; two vehicles with different... view full answer...
I spoke with my contact at Rhino Rack and he said that from the gutters of your 2013 Jeep Wrangler Unlimited up the Rhino Rack part # RRSG59 will add about 5-1/2 inches.
This rack has a weight capacity of 88 lbs. You will need to consult the owners manual of your Jeep to determine what is recommended in terms of roof capacity and be sure not to exceed this figure. view full answer...
Yes, the Bestop Safari Bikini Top, # B5258435-B51243, can be installed on a 2014 Jeep Wrangler Unlimited without the factory door surrounds.
However, removing the door surrounds may cause some water to leak between the door an the top when raining. The harder the rain the larger the amount of leakage you may encounter.
If water leakage does not bother you, then you can remove the door surroundings and install the top. However, if you do not want to take a chance on water leaking in,... view full answer...
The towing capacity of your motorhome should be listed in the owner's manual. Typically if you know your GVWR (gross vehicle weight rating) and your GCWR (gross combined weight rating) you can subtract your GVWR from your GCWR to find out how much you can tow. If you already have a trailer hitch installed on the motorhome it would have weight ratings listed on it as well but those can be higher than the weight rating of the vehicle it is installed on so it isn't a great way to determine... view full answer...
The Thule Replacement Clear Film for Thule Hullavator, part # 853-5481, is a sheet that has four pieces of clear film that is designed to peel off the sheet and be applied to the flanges on the Thule Hullavator bar mount. The Thule Hullavator is a rooftop kayak carrier. The size of each individual piece of clear film is 1-3/8 inch x 1-1/16 inch and is paper thin.
These pieces are applied to the bar mount to protect the cross bar of your vehicles roof rack when the Hullavator bar mount... view full answer...
Timbren rear suspension jounce spring kit # TJRJK is a confirmed fit on the 2014 Jeep Wrangler Unlimited 4WD. I went to our warehouse to measure these springs for you and found their overall end to end length is 4-1/4-inches and the diameter is 2-1/2-inches. view full answer...
The Curt Trailer Hitch Mounted Step with Anti-Skid Surface, # C31001, is 6-3/8 inches front to back and 10-3/4 inches wide. I added dimensions to a picture showing these measurements for you.
You may also want to consider the our Hitch Lock, # e98882, to secure the step in your hitch.
If you wanted a larger step, check out the PortablePET Twistep Hitch Mounted Step, # HE3052, that is 22 inches wide x 19 inches deep. To secure this step in your 2 inch hitch you can use the Threaded Trailer... view full answer...
From the rear of the coupler portion on the Demco A-Frame Coupler # DM14793-81 to the center of the center bolt hole there is a distance of 4-1/2 inches. From the rear of the A-Frame mount to the center of the center hole there is a distance of 4-3/4 inches. From the top of the plate to the center of the mounting hole there is a distance of 1-3/4 inches.
I have attached a diagram to assist. view full answer...
Any trailer hitch that can safely be used with a weight distribution/sway control system (WD/SC) will indicate this capability on its safety/warning sticker. You cannot use such a system unless the hitch manufacturer indicates that this is permissible, such as with hitch # DT78MR.
Most times a 2-inch hitch will be rated as Class III, not Class II. The Class II hitches we offer are all the 1-1/4-inch size. On the linked page you can see all aftermarket hitches in both sizes and classes... view full answer...
The Spare Tire Carrier for Roadmaster Tow Dollies # RM-2000-7 will only fit wheels up to 14 inches in diameter, so it won't work with your large 8 lug, 16 inch wheel and tire combo.
The only option we do have for a spare tire carrier for a wheel and tire that large is the Roadmaster Hitch Mounted Spare Tire Carrier with 2" Receiver Opening # RM-195225.
This is also compatible for use with the Roadmaster tow dollies as well if you are looking to use one of those dollies and carry a large... view full answer...
The spare tire on your 2016 Jeep Wrangler Unlimited poses a clearance challenge for transporting a wheelchair on a hitch-mounted carrier. The use of a hitch extension like # C45791 will get you an extra 8-inches of clearance at the spare tire, but the use of any adapter like this also costs you 50-percent of your hitch capacity. This is due to the extra leverage applied to the hitch from the load being further away from it.
The 2-inch hitches for your Wrangler Unlimited (shown on the linked... view full answer...
What determines if a cargo carrier will fold is the distance from the center hitch pin hole to the nearest point on the carrier when the rack is folded up compared to the distance from the center hitch pin hole to the furthest point of the spare tire. This distance depends on the size of the shank that is inserted into the receiver for each product. We determine this distance on most of the products we sell and it is listed in the "Product Specifications" section of the item's detailed... view full answer...
The thickness of the steel used on the Bulldog Winch Mount # BDW20353 is 5 mm which is close to 3/16 of an inch and also basically 6 gauge. view full answer...
The weight rating for the gutter mount system from Rhino-Rack is really 88 lbs for your 2022 Jeep Wrangler Unlimited with the hard top. Since there are many other options out there with a higher rating I recommend going a different direction.
For your application I recommend the Rhino-Rack Backbone roof rack system which consists of the following:
59" HD Crossbars - # RB1500B-2
Quick Mount Legs - # RRRLT600
Backbone System - # RRRJLB1
Rubber Bases - # RRQMFK06
Spacer Blocks - # RRQMHD05-2
This... view full answer...