I will be happy to provide you with the dimensions and hole spacing on the brackets included with trailer hitch # 41990-07 to see if it will work on your cab and chassis 2004 Ford F-550. I have included a picture with the measurements. view full answer...
The overall width of the Buyers Products Class 4 Service Body Long Hitch Receiver # 3371801055 that you referenced 44-1/2 inches. I attached a picture that has that dimension and a few others listed as well. view full answer...
I spoke with my contact at Optronics about the Wishbone 4-Way Trailer Wiring Harness, # A20WB. They had documentation stating the green wire is 19 gauge and the yellow wire is 20 gauge. She could not state for sure what gauge the white and brown wires are but either 19 or 20. view full answer...
We do offer adapters that allow a gooseneck hitch to tow a 5th wheel trailer and some of these adapters have offset to provide additional turning clearance between the truck and trailer. You may still not be able to make a full 90-degree turn with one of these adapters, depending on the king pin to trailer distance, but you can gain useful additional turning clearance.
You will need to measure from the center of the 5th wheel king pin straight back to the nearest part of the trailer. This... view full answer...
The linked instructions for the custom-fit Draw-Tite Ultra-Frame Class V hitch # 41947 show specific height dimensions from the bottom of the vehicle frame down to the top of the hitch receiver tube. The adjustable side brackets can place the receiver either 6-5/8-, 8-1/4- or 10-1/4-inches below the bottom of the frame rail when this hitch is installed on one of the intended vehicles.
A better option in your application on an RV is to use one of our adjustable-fit frame-mounted RV hitches,... view full answer...
I went out to the warehouse to take some measurements of Curt trailer hitch # C14082. I made a picture showing the measurements for you.
The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the next hole.
The center of the second hole to the center of the round clearance hole is 2 inches.
And from the center of that round clearance hole to the center of the last hole is 1-5/16 inches.
The crosstube is 2-1/2 inches square.
The... view full answer...
In the attached diagram the A measurement is actually the distance from the center of the spring hangers for a single axle trailer. The spring eye to spring eye measurement for your leaf springs will be slightly different.
The B measurement that you see is simply the distance between the center of the axle and trailer frame. I have attached another diagram from the Single-Axle Trailer Hanger Kit for Double-Eye Springs # APS3 product page to help demonstrate this.
If you have an axle with... view full answer...
I just went out and re-measured the hook of the Rack'em Motorcycle Helmut Rack # RA-22.
The inside length of the hook is 1-1/2 inches and it reaches about 1-1/4 inches from the main upright. It's also about 1-1/4 inches from the top of the upright to the bottom of the opening of the hook on the inside. view full answer...
When the Lippert Solidstep RV steps like the part # LC733932 are installed and in the vertical/stored position they take up about 10-1/2 inches through the door threshold. So you would need to measure about 10-1/2 inches into the RV from the doorway to know where it would sit. view full answer...
First, 170 mm is 6.69 inches. The Dexstar Steel Dual Trailer Wheel - 16inch x 6inch - 8 on 6-1/2 - 4.88inch Pilot - Silver Item # AM20790 that you referenced has a bolt pattern of 8 on 6-1/2 inches so it would be close but not the same.
We do not have anything that uses a bolt pattern of 8 on 170 mm. view full answer...
Unfortunately, I wasn't able to get the exact measurements for you. I contacted Timbren because we don't have the # TUMDF70 in our warehouse.
They did tell me the bolt holes will line up with the frame for their application. So you can compare them to the bolts on the front of your truck you should be able to verify the 3 inches.
The height of the spring itself is 5-1/8 inches so it'll definitely be taller that what you have. The bracket will add maybe another 1/4 inch or so. view full answer...
The mounting holes are 16-1/4 inches apart on the Curt hitch, part # C15845. Also the rivet holes are 3 inches apart. I've included the diagrams of all the mounting hole measurements for you. As well as the install details of the hitch. view full answer...
The Curt Trailer Hitch Receiver part # C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of this drop for you as well. If this will not work, please let me know what are looking for so I can further assist. view full answer...
Please refer to the included images I made showing measurements for Curt trailer hitch # C14048. This hitch is designed to fit 1999 to 2016 Ford cab and chassis model trucks. Those are the trucks sold without a bed and are then turned into service vehicles, flat beds, and utility trucks. view full answer...
Yes, there is! To add a hitch to your 2003 E-450 Shuttle Bus, I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver item # 41990-07. This is a universal hitch that can either be welded or bolted on to your Ford. There are no custom fit options available but we have had many customers install this hitch on E-450s.
The Draw-Tite Hitch Receiver item # 41990-07 is a class V hitch with a 2" receiver. It has a massive 16,000 lbs capacity. This one comes with 7" mounting brackets... view full answer...
In regards to the Replacement Upper Bracket for Firestone Ride-Rite Air Helper Springs part # F5187, the distance between the frame mounting holes is 12-1/2" left to right on center. I have attached a photo below with this measurement. view full answer...
The Curt Trailer Hitch Receiver # C15845 is a custom fit application for a 2008 Ford F-350 Cab and Chassis like what you have. I'm not 100% sure what all comes on the Knapheide 6108D54J1 Service Body so I'm attaching a photo of some of the dimensions of this hitch for you to check out and compare with your truck body.
If this doesn't work then the Curt Class 5 Universal Weld-on Hitch w/ Brackets # C37CR might be a valid alternative. This is also designed for service body vehicles but had... view full answer...
The Curt # C14048 measures 16-1/16 inches from the back to the center of the 3 front holes. Those front holes are all 1-1/2 inches on center so you technically could use the 14.565 inch measurement. There is not one that is closer to 15 inches in mounting hole dimensions.
The Curt # C15410 measures 13-1/2 inches from front to back on center if you need a smaller distance which makes the overall distance of the mount right around 15 inches. view full answer...
The straight hose measures 13" from tip to tip and the 90 degree hose measures 10" from bend to tip of the Wheel Masters kit you asked about, which is the following part number:
- Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Hub Mount # WM8001 view full answer...