The Air Lift LoadLifter 5000 Ultimate Air Springs w/ Internal Bumpers # AL88365 have a design height of 6".
These springs have a load capacity of 5,000lbs, is made in the United States, and includes all the hardware for installation.
Additionally, if you do not have a compressor, I recommend taking a look at the:
-Air Lift WirelessAIR Compressor System for Air Helper Springs # AL74000EZ.
This system will allow you to adjust your springs individually with the wireless remote controller,... view full answer...
The Longview Original Custom Slide-On Towing Mirrors # CTM3100 have a mirror surface that measures 5-1/2 H x 4-1/2 W. The plastic housing from end to end measures 16-inches long. Both the mirrored glass part and the housing have gently curved shapes so exact dimensions will vary depending on where you measure but the dimensions above were taken at the center of the glass and housing.
These custom-fit mirrors are intended for various Dodge vehicles for model years 1994 through 1997. view full answer...
The exact answer will depend on the cab configuration, the bed length and whether the truck has the Rambox option.
For a crew cab long bed, the max towing capacity is 12,400 lbs, 12,550 for the short bed.
For a crew cab short bed with Ramboxes, the max capacity is 12,350.
For a mega cab short bed, the capacity is 12,150, 12,100 if equipped with Ramboxes. view full answer...
The Firestone Inflation Valve you mentioned, part # F3032-1 has the thread size of a standard Schrader valve, which is .305-32 (.305 outside diameter with 32 threads per inch). view full answer...
First, for a 2007 Dodge Ram, the correct 100 series tailgate is # VGD-02-100. I went out to the warehouse and measured the tubing used on this tailgate for you. The larger pieces are 1 inch square. These are the top pieces that you see and are also used on the bottom. The smaller round tube pieces are 1/2 inch in diameter. I have included a link to a video showing a typical installation for you. view full answer...
Anytime you wish to tow a fifth wheel trailer using a truck with a bed any shorter than 8 feet, you will need either a slider, like part # RP30051, or a Sidewinder like those found on the page below, to relocate the pivot point further to the rear to provide the necessary clearance.
You can calculate how much clearance you will need. Use the formula on the Sidewinder page linked below to ensure there will be enough space between your truck cab and trailer when executing a 90 degree turn.... view full answer...
I am not aware of a specific website that would have that information. The GCVW should be in the owner manual, and on the sticker on the driver side door jamb. You could also call the service department at your Dodge dealer, with your VIN number, they might be able to get you that information. view full answer...
The 2-5/16" Hitch Ball # BWTS10052 included with the B&W Tow & Stow Pintle Hook # BWTS10056 is only rated for 10,000lbs. This is the only weight capacity 2-5/16" ball available for this hitch. As the pintle places the weight of the trailer on the entire assembly rather than only being on the ball itself it is capable of the higher rating. view full answer...
The Armored Trailer Clearance and Side Marker Light, # MC82RB, utilizes a 194 bulb like the Replacement Side Marker Light Bulb, # A194B. This particular bulb draws 2.7 amps at 14 volts input.
If you need lights that draw less amperage you can use LED lights. The LED equivalent to the # MC82RB light is the Steel Armored LED Trailer Clearance and Side Marker Light, # MCL86RB, which draws .160 amps at 12.8 volts input. I posted a video review of this light for you to check out, see link. view full answer...
We did have a customer come back and tell us that their TorkLift SuperHitch Magnum # TLD1102-30 did fit with their Hellwig sway bar but we don't have specific instructions for the sway bar or the hitch. view full answer...
The Replacement Quick Turn Puck for Reese Elite Under Bed System part # 116517 is about 2-1/8" tall overall. I am not sure what you mean by puck height but this is the only height measurement I have on hand for the Replacement Quick Turn Puck for Reese Elite Under Bed System. view full answer...
That depends on the width of the equalizer used in the suspension setup. Let's say you were using the tandem hanger kit part # APT8 though which has a 7-1/2 inch wide equalizer though. The distance between the hangers would be 28 inches using the # e59SR which measures 23-1/8 inches.
Basically with this spring you want to have 24-1/4 inches between the hangers on the outside of the setup and the bolt hole center of the equalizer side it attaches to using shackles. So roughly you want... view full answer...
I found an online copy of the owners manual for the 2012 Dodge Ram 1500. According to the manual with the 4.7 liter engine, and 2-wheel drive the maximum gross trailer weight can be 7,600 pounds. The payload (the amount of weight the truck bed can hold) is 1,700 pounds.
That means that any 5th wheel trailer would have to weigh 7,600 pounds or less when loaded and ready to tow and have a pin weight of no more than 1,700 pounds. view full answer...
The wheel on Fulton trailer jack # FXP10 is 6 inches in diameter and 2 inches wide. This jack fits 3 x 5 inch trailer frames. Measure the width of the top of the frame and the height of the frame to determine if this jack will fit. If you get a different frame measurement I can recommend a different jack for you. view full answer...
The suspension enhancement systems we offer are not designed to increase the towing capacity of your 2014 Dodge Power Wagon. From my research I found the maximum towing capacity for a 2500 is 20,000 lbs and for a 3500 series, the towing capacity is 30,000 lbs.
A system like the Timbren Rear Suspension Enhancement System, part # TDR2500D, is designed to help the vehicle when a heavier load is placed on the rear of the vehicle. It will not affect the ride of the truck when no load is placed... view full answer...
I went out to the warehouse and pulled both B&W pintle mount # BWPMHD14004 and Tow Ready pintle combo # TR63011 and put them together to measure drop. In the lowest position, the drop is 11-1/2 inches.
To clarify how I measured, I measured from the top of the shank to the top of the ball platform. view full answer...
The top bracket included with the Air Lift LoadLifter 5000 # AL88215 that fits your 1999 Dodge Ram 2500 measures 13.63 inches at its widest point. The depth is 5.75 inches and height is 5.12 inches. view full answer...