Hey Joseph,
To determine the towing capacity of your 2019 Subaru Outback you'll need to find the Gross Combined Vehicle Weight Rating (GCVWR) and subtract the Gross Vehicle Weight Rating (GVWR) of your Outback to determine the maximum loaded trailer weight you can tow. This information is typically in the owner's manual or on a s ticker in the driver's side door jamb or inside the glove box.
Towing a trailer will likely sag the suspension and affect your handling so I recommend installing... view full answer...
We are only going to have a 94" # 8327864 and 95" # 8327834 width for a 7,000lb axle beam. If you are wanting a solid axle beam like this the same width as your F-250 it would have to be special ordered from a local dealer. Otherwise we do offer the Timbren Axle-Less Trailer Suspension # TASR7KS01 which will allow you to customize the width of the axle based on the mounts. Each hub face will sit 6-1/4" from the frame rail it is mounted to. This system has its own suspension setup built... view full answer...
Adding the Ark Drop Down Corner RV Stabilizer Jacks # AR94FR or # ARK94FR for black would make a difference in stabilization. Although you don't want to go overboard adding things, more is generally better for trailer stabilization. Installing these on the corners of your 2023 NoBo will help reduce that movement when you're inside.
Another option would be to add the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025. These attach to the existing scissor jacks and lock... view full answer...
Hey David,
To ease the installation of your spring bars you'll just want to couple up to the trailer, lock the coupler, and then use the tongue jack to lift the trailer back up and take the load off of the truck's suspension. Push it high enough and the spring bars will likely go on by hand, without even having to use the lift tool.
The SuperSprings Custom Suspension Stabilizer and Sway Control Kit # SSA28 you were looking at is essentially an extra leaf spring to add to your leaf spring... view full answer...
Yes, the Timbren Axle-Less Trailer Suspension # A35RS545 can be mounted to your 2-1/2" by 2-1/2" square tubing. Depending on your trailers structure you may need to add an additional crossmember to prevent the frame from twisting but this is covered in the installation instructions which I have included near the bottom of the page.
For 10" tires and wheels we have the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel # AM3H480 or Galvanized Wheel # AM3H490. Do understand these are... view full answer...
Yes, you are able to use the MORryde X-Factor Crossmember # MR33WR but on the Correct Track front and rear hangers you would also need the Adapter Kit # MR93WR. I do not see any plumbing or other components on your 2018 Highland Range Open Range 374BHS that would prevent the installation of them on your trailer. Also the Equa-Flex can still be used. view full answer...
Thanks for reaching out, Scott!
The "W" shape formed by your equalizer, shackles, and leaf springs actually looks to be just fine. Since your 25-1/4" Long 5-Leaf Double-Eye Springs # e34SR are the same and you have the same distance between your hangers I don't really see any issues here. I've attached a photo of this same location from our installation of the same leaf spring for you to reference.
If that "W" shape were to be spread out too much then yes, you would have trouble. Basically... view full answer...
Hey Kimberly, sorry to hear about that. First thing to check it to make sure the trailer is sitting as level as possible. If it's nose high or low that could cause sway. Also try to move as much weight forward in the trailer and see if that helps.
Other than that check the trailer suspension components like the leaf springs to see if there's an issue there. view full answer...
Hi David,
765lbs is quite a bit of tongue weight so it's completely normal for the rear end of the truck to sag until you get the weight distribution hitch spring bars in place to help distribute the weight. I typically just couple the trailer up to the truck and lock the coupler and then just the trailer jack to lift the tongue back up to make installing the spring bars safe and easy.
You can also install some aftermarket suspension enhancement to help handle the load in conjunction... view full answer...
Yes, I was able to verify with Stealth Hitches their Hidden Rack Receiver # SH34VR is confirmed to fit your 2020 BMW M340i sedan. If you are going to need to tow a trailer or wish to use Auxiliary Lights # C53201 behind your BMW you will also want the Towing Kit w/ Ball Mount and Trailer Wiring # 391CONVA7 view full answer...
Yes, if you installed the Go Power Solar Cable Entry Plate part # 34273841REVA on the front of your trailer you'd be fine Randy. Just be sure to have the connectors facing down and you'd be good. view full answer...
Yes, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C48ZV is indeed a Curt part. We do not have a video at this time. view full answer...
Hey Shyanne, thanks for reaching out!
To convert your 12V DC power to AC power for an air conditioner I recommend the Progressive Dynamics 2000 Watt Inverter w/ Transfer Switch # PD64FR, and then using a 15K Btu Furrion Chill HE air conditioner which comes with either a manual operation as part # FR32PR or with a thermostat as part # FR23PV.
This inverter has enough power to comfortably run either AC unit and then the transfer switch gives you the option to add a shore power connection... view full answer...
Hey David, so the trailer hitches we carry like the # 75579 do not come with trailer wiring as not everyone uses a hitch for towing. So you would need a harness as well and the one I would recommend is the Tekonsha part # 118534 as it installs easier and has the most reliable converter box. view full answer...
Yes, you are able to tow a 6x12 utility trailer with the Hidden Hitch by Draw-Tite Trailer Hitch Receiver # DT82GR on your 2016 Volvo XC90. It is recommend to use the Quick Links # RM-910022 for attaching the trailers safety chains and you will need a Ball Mount # 3371803307.
Your trailer likely has a 4-way flat and will need the Curt T-Connector Vehicle Wiring Harness # C56285 installed on your XC90 to connect to. view full answer...
Hey Donald, for your 2023 Kia Telluride the best trailer wiring option available is the Tekonsha part # TK68KR which installs easily by plugging inline with the taillight connectors and also comes with the most reliable converter box. view full answer...
The battery type doesn't matter in this situation as you could still face this issue with two AGM batteries. If you're vehicle is running the alternator should be charging the start battery more than the draw from the 7-way 12v accessory pin. As long as the alternator is properly functioning you shouldn't have an issue charging both batteries while driving.
If the vehicle is off and the 7-way isn't tied to the ignition for power then you run the risk of draining the start battery if you're... view full answer...
Hey Miles, so the Curt tow bar lighting kit part # C96JR that you referenced installs by plugging inline with the taillight connectors of the vehicle so it's not going to interfere with any trailer wiring. view full answer...
I would not recommend installing a Diode # RM-690 on the brake line as this is a part which can fail and if it were to you could risk doing a lot of damage. While the Bright Way Push-to-Test ICU Trailer Breakaway Kit # BW94FR could risk damage to your brake controller the breakaway cord should only ever be pulled when the trailer becomes disconnected from your tow vehicle or during testing which you should not be connected during either. If you are connected electronically to the trailer... view full answer...