The Modulite that the local place was referring to is the black box you see on part # 118468. Rest assured, this is the correct part for your 2009 Scion xB. The 2009 xB has separate brake and turn bulbs, so the box combines these two signals so it can hook up to standard trailer light systems.
There is also a loose red wire lead on the box that does need to be run to the battery. This is so the trailer is powered directly from the battery instead of pulling extra power through the factory... view full answer...
Replacement Locking Knob # P1040 will allow you to add or replace the locking knob on any their Original and XP Series Bike Carriers. This lock functions to secure the outermost bike on the rack, which does protect the other bikes.
To secure one of these racks to your 1-1/4-inch hitch receiver you can use a hitch lock like # S64029. view full answer...
Thank you for the photos they were very helpful. What you have on your vehicle is a 4-way flat, and on your trailer you have a 7-way round, which is less common than a 7-way blade-style, but there is still an option for you to connect the two.
The correct part adapter for this is the Custer Trailer Connector Adapter - 4-Way Flat to 7-Way Round # KIT-7P-4.
If you just want to use it for your the same functions as your 4-way - the turn signals and tail lights - you only need to plug your... view full answer...
The part you mentioned is the fit kit for a Rhino-Rack roof rack on your 2013 Scion xB, and to complete the roof rack you'll need to add crossbars and the mounting feet, and the locks do come with it. Here is a list of the parts you'd need to add this rack to your Scion:
- Rhino-Rack Vortex Aero Crossbars # RRVA137B-2
- Rhino-Rack 2500 Series Legs for Vortex Aero Crossbars # RRRLKVA
- Custom DK Fit Kit # DK152
I have added a photo which shows the rack on a Scion xB. view full answer...
For your 2006 Scion XB, I recommend starting with the Curt Trailer Hitch Receiver # C11487. This is a custom fit and will use ball mount # C45521, along with pin and clip # F-4 and ball # A-82. The wiring harness for your vehicle is the Curt # C56030, which will connect to the factory wiring behind the trim panels in the cargo area on each side. Then you simply need your small trailer with a 2 inch coupler to match the hitch ball and you'll be good to go.
You may want to consider a wheel... view full answer...
The best thing to use would be an anit-rattle kit like the Curt Anti-Rattle Kit, part # F-315. You will use this in place of the pin and clip that you are using now to hold your Pro Series Cargo Carrier # 63155 in your receiver more securely by reducing the play.
Another option that might offer some more peace of mind is the SilentACT Anti-Rattle Trailer Hitch Receiver Lock, part # SHP2082. This will not only take the play out of your current setup, but it will also lock your cargo carrier... view full answer...
I spoke with my contact at Thule, and unfortunately there is not a fit kit to fit your Thule Wingbar Evo to your 2008 Scion xB.
With that being said I know it's not what you'd like to do, but If you need a roof rack you're going to have to get a new setup, unfortunately.
I recommend checking out the Inno Aero Crossbars # INXB153-2, with the feet # INXS250, and the fit kit # INK300.
These crossbars measure 60" (152 cm) 3-1/8" wide x 1-1/8" tall, and has a maximum weight capacity of 165-lbs. view full answer...
I may have a solution for you but Rhino-Rack does not have a 3-bike hanging hitch mount bike rack.
Since you're going to be carrying three bikes you'll need the Class II Curt Trailer Hitch Receiver # C12490. It's confirmed to fit your 2015 Scion xB and a Class I hitch cannot carry more than two bikes.
With the Curt hitch you will also need the support strap # 18050. It's required by Curt when using the hitch for any non-trailer loads like a bike rack.
For a 3-bike rack I recommend... view full answer...
The highest-rated trailer hitch available for your 2010 Scion xB is a Class II hitch from Curt:
- Curt Class II Trailer Hitch Receiver # C12490
The Class II rating means it is stronger than a Class I, but it still has a 1-1/4" receiver. Since motorcycle carriers need a larger/stronger 2" receiver, and a hitch adapter cuts the weight capacity in half, I recommend finding a small trailer to transport your motorcycle if the Scion xB is your only vehicle available to use.
To tow a trailer... view full answer...
The good news is that the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs - Side Loading # TH898 will fit on most aftermarket and factory roof racks, so there are some options available for your 2012 Scion xB.
I recommend using the Rhino Rack for 2012 Scion xB that uses the Rhino Rack Vortex Aero bars # RRVA137B-2, the Rhino Rack 2500 Series Legs # RRRLKVA and Fit Kit # DK152. This kit will provide you with a high quality and durable roof rack to fit on the naked roof... view full answer...
Go To Results