Expert Answers about Nissan Versa

• Does Bumper Fascia have to be Cut or Trimmed to Install Trailer Hitch on a 2014 Nissan Versa
• You will have to trim the heat shield to install Curt trailer hitch # C11256 on your 2014 Nissan Versa, but not the bumper. I have included a link to the installation instructions for you that show where to trim the heat shield. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch. For a bike...
  view full answer...


• How to Install a Trailer Wiring Harness on a 2013 Nissan Versa
• If you already have the # C59496 harness, you can use it on a 2013 Nissan Versa, but the recommended harness is # C56175. As you have found out you cannot go color for color. You will need to use a circuit tester like # PTW2993 to test the taillight wiring and then splice in the harness wires accordingly. On the harness, white is ground and attaches to a clean bare metal surface. Yellow is from the left turn signal. Brown is for running lights. Red is for brake lights. And green is for...
  view full answer...


• How to Determine Installation Cost to Install a Trailer Hitch on a 2009 Nissan Versa
• If you are talking about the actual cost of the trailer hitch then that depends on the hitch. The most cost effective hitch we carry for your 2009 Nissan Versa is the Curt Class 1 Hitch # C11348. If you are going to have the hitch professionally installed then you are looking at anywhere from 1/2 hour to an hour labor charge. You would need to call around to get the going rate for labor in your area. I have included a link to the installation instructions for you to view. You can also see...
  view full answer...


• Installation Instructions for Taillight Converter Hardwire Kit # C59496, 2010 Nissan Versa
• We do offer a plug and play wiring harness option as part # 118545 that you might prefer. The Upgraded Circuit Protected Taillight Converter Hardwire Kit, # C59496, is a universal trailer wiring harness. Vehicle specific installation instructions are not available due to the fact that this harness fits many vehicles. But there are general instructions which I will outline below. First, you will need access to the wiring behind each tail light. Starting on the left (driver) side, you will...
  view full answer...


• Estimated Installation Time of Curt Trailer Hitch # 11348 On a 2011 Nissan Versa
• The estimated installation time for the Curt Trailer Hitch Receiver with Drawbar, part # 11348, is 30 minutes for a professional and 60 minutes for a Novice. Since you are an experienced mechanic, I would say it should not take you longer than 45 minutes tops to install. The Curt Hitch # 11348 Includes a Drawbar, Pin and Clip. To complete your towing setup, you may be interested in the following items: Vehicle Wiring, part # 118545 1-7/8 Inch Hitch Ball, part # 19256 2 Inch Hitch Ball,...
  view full answer...


• Routing Trailer Wiring Harness Power Wire on a 2012 Nissan Versa Hatchback
• There are a few different ways that you can route the power wiring for wiring harness # 118545 on your 2012 Nissan Versa hatchback. It all depends on how you want to route it. The 3 basic methods are under the vehicle exposed, under the vehicle semi-exposed, and through the interior of the vehicle. I wrote a help article, linked to the right, that covers the different methods that you can look through. The actual installation instructions, also linked to the right, do not offer detailed...
  view full answer...