I double-checked with the manufacturer and can verify that the tongue weight capacity is 525 lbs for the hitch that fits your 2021 Toyota Venza, which is the following part number:
- Curt Trailer Hitch Receiver # C89UR view full answer...
Any vehicle's towing capacity is set in stone. If the maximum for your 2009 Toyota Venza is 3,500 pounds then it cannot tow more than that whether you are using weight distribution or not and regardless of what the hitches are rated for.
Check the vehicle owner's manual because sometimes vehicles can have a weight carrying capacity (not using weight distribution) and a separate capacity listed when using weight distribution. But I am fairly certain that your Venza is limited to 3,500 pounds... view full answer...
I pulled one of the # 37185 wiring harness kits from our warehouse and measured the mounting bracket holes.
I have attached a photo of the bracket with the dimensions noted. The distance between the mounting holes is 2.25 inches. I have attached a link to a product review video you can check out. view full answer...
I wouldn't recommend resting any weight whatsoever directly upon the glass panels that make up the panoramic roof of your Venza. The glass that makes up that sunroof is very expensive to replace.
If you're wanting to carry cargo on the roof, your best bet would be to use a Yakima Q-Tower roof rack and a small cargo basket like the Thule # TH859XT. According to Yakima, when installed on the Venza, the roof rack will have a 125 lb capacity and would consist of the following parts:
58 inch... view full answer...
The Curt Trailer Hitch Receiver part # C89UR which is a fit for a 2021 Toyota Venza has a class III rating therefore the lowest the tongue weight could ever be is 350 lbs but for this hitch it's actually a bit higher at 525 lbs. The lowest rating a class III trailer hitch can have to maintain the class III is 350 lbs tongue weight and 3,500 lbs gross trailer weight but it can be rated for me as you can see. view full answer...
That depends on how heavy your bikes are. If they are below the weight capacity of the Thule Passage Bike Carrier part # TH910XT then you would be fine. The weight capacity for this rack is 35 lbs per bike.
Check out the review video I attached for this rack as well.
If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Swagman Easy-Out Women's and Alternative Frame Bike Adapter # 64005 to provide a horizontal... view full answer...
The F measurement is the length of the square portion of the spindle stub, which can either slide into the end of the axle and be plug welded in place or more commonly welded to the bottom of the axle tube.
As long as the spindle is going on a 3500 lb axle and the rest of the dimensions match (B, C, D and E), it is not so important that the F dimension match perfectly, just as long as it is not dramatically shorter than the spindle it replaces. view full answer...
I took a look at the installation instructions and checked with our vendor, the etrailer Hitch item # e25AR will not obstruct any of your sensors. This hitch is confirmed to fit your 2021 Toyota Venza. The crosstube mounts completely behind your bumper cover so the only part visible is the 2" x 2" receiver.
I have linked an installation video below so you can see the process.
If you ever have the need to tow you will also want a wiring harness item # C57ER and a ball mount kit item # C45534. view full answer...
The GearSpace 34 cargo carrier # HGK819 is 10" from the center of the hitch pin hole to the closest edge of the carrier when retracted but 31" when slid out. view full answer...
The Curt hitch that fits your 2021 Toyota Venza # C89UR is interesting in that it has the 2 inch hitch size that Class III hitches normally have but has the lower weight capacity of a Class I hitch. So what this calls attention to is the hitch Classification is mostly just used as a way to organize the different capacities and hitch sizes but the "rules" on them aren't set in stone.
So with this hitch you'd have a 2 inch hitch that has the lower capacities. view full answer...
The Ultra-Fab Carrier, part # UF48-979033 weighs 50 pounds. Depending on the tongue weight capacity of your vehicle, you will need to add the weight of the carrier and the bike to make sure you do not exceed the capacity of the vehicle or the hitch.
The tongue weight of a trailer hitch is typically 10 percent of the towing capacity of the hitch. view full answer...
Both the Draw Tite hitch # 75663 and the Curt # 13356 have open back hitch tubes so your bike rack would fit easily without a depth interference like you mentioned. view full answer...
To add a hitch to your 2021 Toyota Venza, I recommend the Curt Trailer Hitch item # C89UR. This hitch is custom fit and bolts to your Toyota with included hardware. I really like the Curt hitch because the crosstube mounts behind your rear bumper cover leaving only the 2" receiver visible. This not only helps with ground clearance but it also looks better.
If you are planning on towing you will also need a wiring harness item # C57ER and a ball mount kit item # C45534.
I also recommend... view full answer...
I am sorry but I checked with all of our vendors and no one has any parts listed for flat towing a 2010 Venza. The Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267 is pretty universal so it should work but I can't confirm.
I wanted to add that I pulled up the owners manual of your 2010 Toyota Venza and your vehicle is not recommended for flat towing. It says to use a tow dolly like the Demco Kar Kaddy item # DM9713045 to tow it behind your RV. This dolly also includes... view full answer...
Go To Results