Expert Answers about Chevrolet Venture
- Could I Mount Two Advantage Cargo Bags # HE3021 on the Roof of my 2000 Chevy Venture
- As long as your roof has the room for two of these Advantage Cargo Bags, part # HE3021, and your roof has the carrying capacity to hold the two bags with luggage in them then you should be able to put two of these bags on the roof rack of your Venture.
The measurements of this bag are 38 inches long, 38 inches wide, 15 inches tall. If your rack is longer than 76 inches from front to back you could probably fit two bags, one behind the other, on the roof of your Venture.
view full answer... - How to Order Replacement Install Hardware for a Trailer
- We do sell replacement hitch hardware with the part number # RHK. You'd need to enter the part number of the hitch you have as well as select its manufacturer and we'll send you out the correct hardware.
view full answer... - Will Constant Power on 12 Volt Circuit After ETBC7 Installation Drain Vehicle Battery
- Yes, after installing # ETBC7 you will have constant power on that circuit. The easiest solution is to just unplug the trailer from the vehicle. Having power at the connector without it going anywhere will not drain the vehicle battery.
If you don't want to unplug the trailer every time you can easily add a battery isolator like # PK5231201. On the power wire, instead of running from the BAT post on the circuit breaker to the battery, you will run it to the output side of the isolator....
view full answer... - Location of Factory Connection Point for Trailer Wiring Harness on a 2003 Chevy Venture
- The plug will be there on a 2003. It is just that we have not had a 2003 Venture in to make a video but we have had a 2002 and 2004.
To find the factory harness you will need to pull up the threshold panel in the cargo area so you can pull back the panel on the driver side. The wiring harness should be nearer the end of the vehicle. It can be either a single connector with nothing plugged into it or two connectors connected together. It can also be located behind an air conditioning unit...
view full answer... - Is Drilling Required for a Class III Hitch Installation on a 1998 Chevy Venture
- All of the hitches available for your 1998 Chevy Venture require drilling for installation. On your 1998 model, you would be required to drill one or two holes, depending on the wheel base length of your vehicle.
If your Venture is a short wheel base model, you would only have to drill for the rear most mounting holes closest to the vehicle bumper for the Draw-Tite # 75278 Class III. Long base models would require additional drilling for the forward most mounting hole on the passenger...
view full answer... - Accessing the Plug for a T-Connector on a 2000 Chevy Venture
- I am sorry to hear that you are having trouble with your T-connector, item # C55355. Most customers assume that the plug is directly behind the drivers side panel in the rear. But the plug is usually behind the air conditioning unit that is directly behind the panel the air conditioning unit will have to be pulled away to access the plug. I hope this helps. Let me know if you need more info.
view full answer... - Where Does the C55355 Install On a 2003 Chevy Venture
- This T-connector will plug into your vehicles wiring harness that is located in the rear cargo area of your van on the drivers-side. I have included a photo showing the location in the rear cargo area of a vehicle similar to yours.
I would recommend using some dielectric grease # 11755 when you are installing this wiring harness, this can be used on all electrical connection points and it helps to prevent corrosion.
After you have completed the installation of the wiring harness, the...
view full answer... - Where is the Trailer Wiring Connection Location on a 2000 Chevy Venture
- On a 2000 Chevy Venture you will need to pull up the threshold panel in the cargo area so you can pull back the panel on the driver side. The wiring harness should be nearer the end of the vehicle. It can be either a single connector with nothing plugged into it or two connectors connected together.
In either case it could be hiding behind another wire bundle or even taped up with another bundle so you cannot see it. I have included links to a couple of videos showing typical installations...
view full answer... - Is Drilling Required When Installing Draw-Tite # 75278 Hitch on 2004 Chevrolet Venture
- The Draw-Tite Class III Max Frame Receiver Hitch # 75278 referenced in your question is confirmed to fit your 2004 Chevrolet Venture. When installing the hitch on your vehicle, you will need to drill a 1/2 inch hole on the vehicle frame rails. I have attached the complete installation instructions that you can also take a look at so you can see exactly what the process will be.
This Class III hitch will provide you with a 2 inch receiver opening and has a 3,500 pound towing weight capacity.
view full answer... - Do Factory Bump Stops Get Trimmed to Install AirLift Air Bags on a 2004 Chevy Venture
- When installing AirLift 1000 system # AL60748 you will need to cut off the bottom 2 sections of the factory bump stops on your 2004 Chevy Venture. There would not be enough room otherwise. I have included a link to the installation instructions for you to view as well.
view full answer... - Cant Find Connector Plug on my 2003 Chevrolet Venture to Install Trailer Wiring C55355
- Since the part # C55355 can fit a few different vehicles with differing setups you will need to check a few places to find the connector you need. First thing I would recommend is checking out the install video I attached to the right that shows this harness being installed on a 2003 Chevy Venture just like yours.
Also, some vehicles will only have one connector. Some of the vehicle options have another connector plugged in series with the taillight connector plug, and the second plug...
view full answer...
Go To Results