No, you won't have to modify the Util-Track system to install the Lomax Hard Tonneau Cover item # LOM66QR. The rails for the tonneau cover mount about the track system on your 2017 Nissan Titan. I have linked the instructions below so you can see the process. view full answer...
The hub bore of Trailer Hub and Drum Assembly # AKHD-655-35-K is 1.980-inches and this allows a good fit with a grease cap like # F001518 which has a flange diameter of 1.988-inches. view full answer...
I spoke with my contact at MagnaFlow and he informed me that all of their cat-back systems are designed to be under the 95 decibel rating that is mandated. He could not give me an exact figure, but you should be fine.
He did say also that all of their systems are tested on stock vehicles where the only thing that is changed is the installation of the cat-back system. So if you install headers, intake or an offroad y-pipe you could exceed this. view full answer...
The Dexter Shackle Bolt for Double Eye Springs # 007-126-01 measures 2-1/4" from bolt head to threaded portion. This bolt is 2-7/8" long and has a thread size of 7/16"-20. You can use Replacement 7/16"-20 Flange Nut # LC122103 with this bolt. I have attached a demonstration video for this bolt. view full answer...
63 inch long tracks are included with the Rhino Rack Roof Rack part # Y02-480B that you referenced. The crossbars are 54 inches long. view full answer...
I spoke with my contact at Flint Hill Goods about the temperature rating. He said that there is no problem with the hitch cover # FHG72VR performing in cold temperatures as low as those you experience in Fairbanks.
The Flint Hill Goods Square LED Brake Light Hitch Cover for 2" Hitches # FHG72VR will fit 2 inch trailer hitch receivers. The light requires a standard 4-way flat trailer connector for power and signal. This lighted hitch cover should work well for your 2013 Nissan Titan Pro... view full answer...
The distance between the holes on the Tow Ready Adjustable Tow Bar, # 63180, mounting bracket measures 4 inches from center to center.
The attached picture will show you additional measurement information for you to review. view full answer...
Curt hitch # 13199 is indeed a correct fit for your 2004 Nissan Titan. This Class III hitch has a 2-inch receiver opening and is rated for 6000-lbs trailer weight and 600-lbs of trailer tongue weight (TW).
TW is the downward force on the hitch ball from the trailer's weight. Usually a properly-loaded trailer's TW will be between 12 and 15-percent of its total gross weight. Trailer hitches, and the vehicles they are bolted to, both have TW ratings and you'll want to ensure your trailer's... view full answer...
I spoke with a representative of Thule, who told me that they did not classify the 450 lb weight capacity of the Thule XSporter # TH500XT as either static or dynamic and that you only needed to have a capacity of less than 450 lbs and you would be fine.
As far as the models you referenced, the only difference is fit. The The Thule XSporter # TH500XT is a fit for a 2017 Nissan Titan, while the # TH500XT-XK3 is for a 2005 - 2015 Toyota Tacoma with a Deck Rail System while the # TH500XT-XK4... view full answer...
There are two dimensions that I can provide for the Malone HighRise # MPG323. The main black part that will attach to the wall is 10-3/16" long; when you put the arm into that piece, which will hold the boat, the length will be 13-1/4" total hanging down. view full answer...
The cable that comes with the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer - Dual Spring - 150-lb Capacity # 362SA8207 is 150" and can be replaced with part # CAB1-8CB150. I confirmed this with my contact at TRC.
If you needed to get a longer cable set then we have the 174" Long Cables as part # M339FR. view full answer...
The height of the SumoSrpings Solo Custom Helper Springs # SS95GR is 5-1/2 inches without the top bolt and 6-1/2 inches with the top bolt. I went ahead and attached a diagram of these dimensions to give you perspective.
If you need the confirmation for a fit with your vehicle, I would be happy to assist you if you provide your year/make/model. view full answer...
The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ37100ET has a measurement of 8 inches from the center of the hitch pin hole to the center of the adjustment holes and then the head # EQ90-02-1000 has a center of hole to center of hitch ball measurement of 4-1/4 inches. So your total length will be 12-1/4 inches from the center of the ball to the center of the hitch pin hole. view full answer...
I went ahead and pulled the product from our inventory and confirmed that the wiring on the Hopkins Vehicle Wiring Harness with 7-Way RV-Style Connector # HM41145 measures 8-3/4 inches from the back of the plug to the end wire connectors. I attached a diagram of that specific measurement to give you a better idea. view full answer...
Thanks for the picture! I am not sure how loaded down you are but your truck and trailer look pretty level. If you're experiencing squatting issues and are sure you have the right capacity weight distribution hitch then yes, adding the SumoSprings Solo Custom Helper Springs item # SS95GR to your 2021 Nissan Titan P4X will benefit you.
The SumoSprings item # SS95GR have a 1,500 lbs load leveling capacity. The best part about SumoSprings is that they work off a system called progressive... view full answer...
Measure from the awning rail on the side of your RV down to see how much clearance you have for an awning rail. The part # LC434730 requires 69 inches of clearance from the rail down. If you have the needed clearance this would be all you'd need. view full answer...
I pulled the Blaylock EZ Lock Coupler Lock, # BLTL-33, from our warehouse and took some measurements for you. The inside width of this coupler lock is 4-3/4 inches. From the base to the bottom of the pin, it measures 3-1/8 inches (see photo).
If you do not have a padlock yet, I recommend looking at the Blaylock EZ Lock Coupler Lock with Padlock, # BLTL-33-40D. This is the same coupler lock, but it includes a stainless steel padlock. You could also just purchase the lock separately as... view full answer...
The Dexter Trailer Hub and Drum Assembly # K08-201-9B that you referenced has a stud length of 1-1/4 inches which is the standard length for trailer hubs like yours. view full answer...