Expert Answers about Toyota Tacoma
- Who Makes Replacement Cover for Extang Tuff Tonno Tarp
- Yes, the Replacement Cover for Extang Tuff Tonno Tarp part # EX13915 is made by Extang.
view full answer... - Identifying the Axle from a Home-Built Trailer
- There are a couple ways to determine what kind of axle you have. If there aren't any part markings on the axle or anywhere else on the trailer frame that list your trailer axle specifications, you need to measure your spindle with a calipers to get a precise measurement. I couldn't find a matching bearing based on the measurements you provided, so make sure you are using the right equipment to take these spindle measurements. You can also measure the axle diameter to get an idea of the...
view full answer... - Color of Mounting Clamps in TracRac TracONE Truck Bed Ladder Rack TH27000XTB-500
- In the TracOne Truck Bed Ladder Rack for Toyota Tacoma # TH27000XTB-500 the aluminum U-channel and C-channel clamps that allow installation are silver in color as these have a natural finish. I confirmed this with my contact at TracRac. These clamps are available separate from the rack itself as part # TH41500.
view full answer... - Can Rhino Rack Hitch Lock for 2 Hitch Stand up to a Hammer?
- The Rhino-Rack Hitch Lock # RRRBCA025 has not been specifically tested with a hammer, though I can confidently tell you that it is highly unlikely for this lock to be broken in any relatively short amount of time with a hammer by anybody not named Thor. No lock is completely unbreakable but a padlock is a big deterrent to theft when there are certainly easier targets available.
I've added a link to a video review of this lock for you to check out (we'll see about getting one up with a...
view full answer... - Is the etrailer.com Receiver Lock Compatible with the OEM Hitch on a 2017 Toyota Tacoma
- The Trailer Hitch Receiver Lock # e98881 that you referenced is compatible with 2" x 2" and 2-1/2" x 2-1/2" trailer hitches so it is compatible with the OEM hitch on your 2017 Toyota Tacoma. You can use the specs to verify if you are still uncertain:
5/8" Diameter pin
Inside width: 3-5/8"
Overall length: 6-7/8"
It does not come in black, but one end is black and the other end that locks the pin has a black dust cap to protect the tumbler from dirt and debris (see attached photo).
If...
view full answer... - Should you Fashion your Own Landing Pads
- I would not recommend trying to fashion the Yakima Landing Pads 24, part # Y74FR, out of aluminum yourself. These fit kits have to be very precise, and trying to make one for yourself will definitely void any kind of warranty on the towers and crossbars.
As for the strength, Yakima has been doing quite well over the years with improving the quality of their products, so you can rest assured that the material of the Landing Pads 24 is strong enough to handle the 165-pound limit of the crossbars....
view full answer... - Where Are Trailer Valet Products Manufactured At
- Trailer Valet products like the Trailer Valet 5X Swivel Jack and Trailer Mover # STC-V211 you mention, is made in China.
view full answer... - Inno Velo Gripper on a Bike with a Carbon Frame
- If the Inno Velo Gripper, part # INRT202, has not been scratching the carbon fork of your current bike, then it probably will not scratch the carbon frame of your new bike.
However, I spoke with Inno on your behalf, and they cannot guarantee there will be no scratching. They recommended using some kind of padding between the grip of the Velo Gripper and the frame.
view full answer... - 7,500LB Class III Ball Mount and Hitch Ball Set That Are Made In The USA
- The Curt Class III Drawbar # C45270 is made in the USA. It has a 4" drop and a 2" rise with a weight capacity of 7,500 lbs..
The Convert-A-Ball Interchangeable Ball Set # 900b is also made in the USA. This will allow you to quickly change from a 1-7/8" ball to a 2" or 2-5/16" without having to remove the ball or draw bar from your receiver.
view full answer... - Ladder Racks Manufactured In The U.S.A
- The Rola Haul-Your-Might T3 Truck Bed Ladder Rack part # 59799 is not made or manufactured in the U.S.A. however, I do have a very similar option that is made and manufactured in the U.S.A. For this, you will want to use the TracRac TracONE Ladder Rack for 2005 to 2015 Toyota Tacoma part # TH27000XTB-TA.
Both the Rola and TracRac ladder racks have an 800 lb. weight capacity, however, the Rola rack comes with a 5 year warranty whereas the TracRac comes with a limited lifetime warranty.
view full answer... - What Are the Highland Auto Floor Mats # 46002 for a 2006 Toyota Tacoma Made Of
- The Highland Auto Floor Mats # 46022 you referenced are made of 100 percent rubber with no carpeting. They do not have the eyelets for your 2006 Toyota Tacoma, but have the raised rubber anti-skid spikes on the bottom. I have included a link to a video review of this product.
I have also provided a link to all our floor mat options for your Tacoma. You will want to select your cab style prior to examining your choices to ensure you get the right floor mat for your vehicle.
view full answer... - Material of ACME Nut for Type 1 Connector on Camco Propane Hose
- I was pretty positive about this but I had the # CAM59823 pulled from our warehouse to make sure. The ACME nut is hard plastic
view full answer... - Does the Bulldog Removable Caster Swivel
- Yes, this Bulldog Removable, 6 inch Steel Caster # BD017125 will swivel so that you can maneuver your trailer right and left if needed.
view full answer... - What Is The Material And Strength Of Replacement Self-Adhesive Hook Strip
- Yes, the Replacement Self-Adhesive Hook Strip # B41973 will work very well for your Bestop cover. It is indeed a Velcro strip. It is not known what the exact strength of this product is, but this is the recommended Bestop Supertop for truck collapsible bed cover replacement.
view full answer...
Go To Results