I do have cargo management options for you but the TruXedo Truck Luggage Expedition Truck Bed Cargo Management System part # TX1705211 will not fit a 2016 Toyota Tacoma due to both the actual size of the bed in addition to interference with the deck rail system. Instead, you would want to look into a chest style toolbox like the DeeZee Red Label Truck Bed Toolbox part # DZ8537 which is 37-1/8" long x 19" wide x 15-9/10" tall and has a 6.4 cu ft storage capacity.
I have attached a review... view full answer...
When installing any Timbren system on the 2019 Toyota Tacoma you should have about 1/2" to 1-1/2" between the frame and the spring after installation. You won't necessarily be losing wheel travel when you use a Timbren Rear Suspension Enhancement System on the Tacoma. I recommend either the # TTORTUN4 system if you have 4 leaf springs in the rear suspension or # TTORTUN4L if you have 3 leaf springs in the rear suspension.
When you switch out the factory bump stops for the Timbren springs... view full answer...
For your application you can use the Reese Pole-Tongue Adapter # RP58393 which works with lift brackets from all manufacturers that mount approximately 30" back from hitch ball. Since your Husky Center Line # HT32215 falls within that category and is rated for 6K (where the adapter is rated for 7.5K) this is the perfect option for you. view full answer...
Yes, we carry the Adarac Pro Series Custom Truck Bed Ladder Rack # A86ZR which is compatible with your 2022 Toyota Tacoma with a 6' bed. The vertical uprights can be repositioned along or removed from the utility rails to accommodate the size of your load. Included channel nuts allow the uprights to slide closer to or further apart from one another along the rail's mounting channels. view full answer...
To install the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 in your 2019 Jayco Seneca on the Freightliner S2RV chassis the wiring is behind the kick panel in the drivers compartment. There is not a connector on the wires, they are simply terminated with tape. You will connect those with the wiring pigtail that is included with the brake controller.
You can use the longer Pigtail # 7894 if you wish to move the brake controller to the right side of the steering column. This pigtail... view full answer...
Yes, we have the Draw-Tite Front Mount Trailer Hitch Receiver # 65070 for your 2023 Toyota Tacoma. This will require trimming of your splash guard to fit and if you have a TRD you will have to permanently remove the front skid plate. The receiver is rated for up to 500lbs of tongue weight, 5,000lbs of trailer weight and a line pull up to 9,000lbs.
I recommend using the QSP Trailer Hitch Silencer and Cover # 63080 with this receiver. This will prevent the whistle noise which is typical... view full answer...
The Curt Trailer Hitch Receiver # 13323 is a rear hitch which fits your 2006 Toyota Tundra. We do carry the Curt Front Mount Trailer Hitch Receiver # 31313 if you are looking for a front hitch. This will require removal of the bumper beam end caps and may require drilling if you are installing on a 2wd truck.
If you are needing the rear hitch we do have the T-One Vehicle Wiring Harness # 118496 which will allow you to connect to the factory wiring to get a 4-way flat connector. view full answer...
It sounds like you are looking for the Pace Edwards Switchblade Retractable Hard Tonneau Cover item # 311-SWTA10A38. This cover is black, made of aluminum, and fits the 5' bed models of the 2023 Toyota Tacoma.
I have linked a couple of pictures below along with a review video.
We also have the Pace Edwards Switchblade Metal Retractable Hard Tonneau Cover item # 311-SMTA10A38. This is also confirmed to fit the 5' bed models of the 2023 Tacoma. view full answer...
I spoke with my contact at Tuson regarding the DirecLink Base Model Trailer Brake Controller # 335DL-100 and your 2006 Toyota Tacoma. The potential issue with regards to fitment for this controller on trucks prior to 2008 is that not all of them are equipped with the factory 16-pin OBD-II port under the dash that this hooks up to. Many previous model year trucks do have this port but many do not, making it difficult to confirm fitment accross the board which is why Tuson lists compatibility... view full answer...
I can help you figure out how to determine the correct electric trailer brakes for your Little Guy trailer with a 2,500 lb axle, and there are a couple of things you'll need to know. So in order to determine the correct electric brake assemblies, you need to know the inside diameter of your hub's drum and have a 4-bolt brake mounting flange on your spindle.
For example, you mentioned you have a 2,500 lb axle, so it is likely your drum measures either 7" diameter or 10" diameter. If it... view full answer...
Since your 2015 Toyota Tacoma doesn't have a hitch or trailer wiring already the wiring harnesses we carry that fit plug in to connectors that are either along the frame rail or behind the tail lights. If you can't find a connector under the rear of the truck then you'll remove the tail lights and connect the harness inline with the tail light wiring. I've linked an install video of the Tekonsha harness, part # 118496, on a 2015 Tacoma. The Tekonsha is what I recommend because it has... view full answer...
Good question, and the difference between the Ride-Rite air bags for your 2021 Toyota Tacoma is actually the fit, as the right one will depend on if your leaf springs are above your axle or below your axle:
- Axle Located Below Leaf Spring Pack: Firestone Ride-Rite Air Helper Springs # F2407
- Axle Located Above Leaf Spring Pack: Firestone Ride-Rite Air Helper Springs # F2410
I have added a photo for you showing the # F2407 on a Tacoma so you have a visual representation of what to look... view full answer...
We do!
For your application I recommend checking out the Hollywood Racks Sport Rider SE2 Bike Rack for 2 Bikes # HR1450Z.
This rack hits all of the things you're looking to get out of a rack at a modest price-point for a 2-bike rack. The operation of the different features is a little more manual than some of the nicer racks but they are still easy to use and gives you something that is easy to live with. view full answer...
The adapter that you have selected, Adapter 7 pole to 4 Pole and 5 Pole, part # 37385 will work perfectly for your 2007 Toyota Tacoma with 7 way plug. It will convert your 7-way to a 4-way or 5-way with your flat trailer connector. view full answer...
Yes, the Firestone Ride-Rite Air Helper Springs part # F2407 will work on a 2017 Toyota Tacoma so long as the axle is below the leaf springs. That said, you'd also need the Firestone Axle Bracket Extension Kit for Lifted Vehicles part # F2506 to compensate for the added lift. view full answer...
It sounds like you are looking for the Pop & Lock Custom Tailgate Handle with Lock # PAL5400 for your 2015 Toyota Tacoma. This uses the BOLT technology to allow you to key the lock to the same key as your ignition. It is not reprogrammable so its can only be used with the one key when it is programmed. We do have the Pop & Lock Custom Tailgate Lock Conversion Kit # PAL8525 which will allow you to combine the tailgate handle with any power locks you may also have. view full answer...
No, the Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers # EX1024 will not fit all makes of tonneau covers. They are specifically a fit for the Extang Solid Fold 2.0 83 series covers. But, we have had some other models from Extang work.
If you can provide me with the tonneau cover that you have, I can look into if the strap and buckle will work for your cover. view full answer...
There is just a single bolt for the Yakima FullSwing Bike Rack for 4 Bikes # Y02465, and for that along with the needed wrench, the correct replacement is the following:
- Replacement Hardware Bag # Y52XR view full answer...
All you'll need to add tracks to your truck cap so you can mount a rooftop tent are the 42 inch Yakima tracks, which are the following part number:
- Yakima 42" Tracks for Roof Racks # Y01126 view full answer...
Go To Results