Recommended Sliding Ladder Rack For A 2022 Toyota Tacoma 6' Bed

Question

Question:

Can you tell me if you have a sliding ladder rack fir a 2022 Tacoma double cab with 6 ft bef

asked by: Richard S

1

Helpful Expert Reply:

Yes, we carry the Adarac Pro Series Custom Truck Bed Ladder Rack # A86ZR which is compatible with your 2022 Toyota Tacoma with a 6' bed. The vertical uprights can be repositioned along or removed from the utility rails to accommodate the size of your load. Included channel nuts allow the uprights to slide closer to or further apart from one another along the rail's mounting channels.

expert reply by: Kevin C

1

Answer 1

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 2

Hey Shannon, thanks for reaching out! Sounds like you're looking for the Thule Xsporter Pro #TH500XTB-THXK3 for your 2008 Toyota Tacoma with the Deck Rail System. This is adjustable up and down as well as along the Deck Rail System so you get the…

view full answer...

Answer 3

The Large Yakima OffGrid #Y07139 Cargo Basket uses crossbar clamps that are designed to be universal. They will fit virtually any crossbar shape, including most aftermarket and OEM crossbars. I was not able to find any schematics online that would…

view full answer...

Answer 4

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 5

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 6

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Yes, if you use the extension #Y07016 with the Yakima SkinnyWarrior Roof Rack Cargo Basket #Y07014-16 it will work fine with your 2023 Toyota Tacoma.

view full answer...

Answer 9

Out of all the brake controllers that we offer for your 2023 Toyota Tacoma I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR. I like this controller because the main unit will be installed out of sight behind the dash, while the…

view full answer...

Answer 10

Hey Tim! Yes, the Rhino-Rack Ski and Fishing Rod Carrier #RR572 will fit the older Thule square crossbars. While this kit does come with T-Slot hardware, it also has the clamps which is what you'll use for the square crossbars.

view full answer...

Answer 11

Those are very good questions and let's start with the capacities of both systems. The SumoSprings Solo Custom Helper Springs #SSR-612-40 has a 500 lb capacity and SumoSprings #SSR-612-47 has a 1,000 lb capacity, which means that is the highest…

view full answer...

Answer 12

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Recommended Sliding Ladder Rack For A 2022 Toyota Tacoma 6' Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching