Yes, I will be able to help you get the correct hitch. The hitch you will need for your 1999 GMC Sonoma with rear fascia and no step bumper is the Curt Class III Trailer Hitch, # 13920. It is a 2 Inch Class III hitch that has a Gross Towing Weight of 3,500 lbs. and a Tongue Weight of 350 lbs.
The Draw-Tite Trailer Hitch, # 75085, you have referenced is for 1999 GMC Sonomas with step-up rear bumpers.
If you will be towing, you will need the Curt Ball Mount, # C45010, and the Pin and Clip,... view full answer...
The Hopkins Plug-In Simple Vehicle Wiring Harness # HM41135 referenced in your question is confirmed to fit your 2004 GMC Sonoma. This will install by connecting the built-in port that is located behind the rear bumper on the driver's side of your vehicle. Once that connection is made, you will have a 4-Way connector to connect with and power a trailer's signal lights.
I have attached the written installation instructions that you can also use for reference. view full answer...
The Draw-Tite Max Frame # 75085 is confirmed to fit your 2004 GMC Sonoma Crew Cab as long as you have either the factory step bumper or non-towing bumper.
If your truck has the factory roll pan bumper then the Curt # 13920 is the correct hitch.
If you're going to be towing with your truck you may also need wiring for your trailer's lights. The Curt Wiring Harness # C55359 will provide a 4-way trailer connector. This installs by plugging into your truck's wiring behind the rear bumper,... view full answer...
For the BrakeMaster you will need a car to RV air line assembly, # RM-921004-88. I also recommend the quick disconnect kit, RV side, # RM-921004-60. And you will need some air line, # RM450700, sold by the foot.
Inside the RV you will need kit # RM-98850.
Dealing with air brake systems can be difficult but not impossible. I will email you a copy of the instructions for BrakeMaster # RM-9100. Current pricing is available on each of the product pages. view full answer...
Adding an electric fan or fans is subject to how much space you have in the engine compartment. The first thing I would check is if your 2003 Sonoma has a fan driven by a serpentine belt (a belt that turns the pulleys of several components) or if it has its own belt.
If the fan is attached to the pulley for the water pump, you will not be able to remove it though the blades may be able to be removed. So if you find that your fan or blades can be removed and you can add an electric fan,... view full answer...
For your 1998 GMC Sonoma, I have included a link to the available trailer hitches. For a Draw-Tite hitch, go with # 75085. This is a Class III trailer hitch rated for 350 pounds tongue weight capacity and 3,500 pounds gross trailer weight. It can also be used with weight distribution for 600 pounds tongue weight capacity and 6,000 pounds gross trailer weight capacity. I have included a link to the installation instructions for you.
If you plan on doing some towing, I recommend the etrailer... view full answer...
Sometimes wiring colors for trailer lighting functions will match up between the truck and trailer but color alone is not a reliable way to identify what a wire does. The best way to confirm the function of each wire on your truck and trailer is to use a circuit tester like # PTW2992 to test each one while a helper activates the truck's various lighting functions. The video linked at right shows how to use the tester.
It sounds like you may have connected multiple lighting circuits to... view full answer...
I spoke with my contact at Derale, and he informed me that the Derale 4-Pass Tube-Fin Power Steering Cooler, part # D13212, does not have turbulators in the tubes.
I also asked him if this would work on the hydraulic system of your Scag lawn mower, and he said that the # D13212 would work as it is pressure tested to 350 psi.
I attached a link to a transmission cooler FAQ page below that you might find informative also. view full answer...
The Magnetic Tow Lights, # RM-2120, plug directly into a 4-Way flat connector on the tow vehicle.
If your are towing the 2003 GMC Sonoma behind another vehicle, I would need to know what connector the truck has at the front and what type of connector the towing vehicle has at the back. Then you can get an adapter to match.
If you are using the Sonoma to tow another vehicle, I would need to know what it has on the back and what the other vehicle has on the front.
There are several different... view full answer...
The Curt Class III hitch you'd looked at, part # C13021 is indeed a fit for the 2002 GMC Sonoma with the factory step bumper, as shown in the provide photo.
If you'll be using the hitch for towing, you can install a 4-pole trailer connector using part # 118359. You'll also need a ball mount like # C45030 and a trailer ball like # 19260 for a 1-7/8 inch or # 63845 for a 2 inch ball and a pin and clip # PC3. view full answer...
The best type of winch for your application is a brake winch like # F143100 from Fulton or one of the others shown on the linked page. These automatically brake when you stop cranking; this will prevent a runaway cart. A rolling 300-lb load like your cart will be fairly easy for a winch to pull up your ramps so one rated for 1500-lbs will be fine.
In order for any winch to deliver its rated performance it must be mounted to a suitable surface and have its bottom plate fully supported by... view full answer...
I do have the correct replacement tonneau cover for you but I spoke to my contact at Extang any they informed me that the Replacement Tarp for Extang BlackMax Soft Tonneau Cover part # EX1560 will not work with your Extang Platinum Classic Tonneau Cover part # EX7560 even with the header seal as the rails are different and will not work with one another.
The correct replacement tarp you will need is the Replacement Cover for Extang Classic Platinum Tonneau Cover part # EX6560. view full answer...
You will be able to keep the spare tire with Curt trailer hitch # C13021 installed on your 2000 GMC Sonoma. There is a note in the instructions, linked for reference, stating that some spare tires may need to be lowered and repositioned for hitch installation. It does not specify sizes though. Usually what this means is that spare will need to be pushed towards the front of the vehicle some.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2... view full answer...
Vortex hubs are made by Tie Down Engineering and are claimed to offer reduced maintenance requirements. We do not offer these hubs but in general a replacement hub can be selected by confirming the axle weight rating, wheel bolt pattern and the bearing set used inside the hub. The inner and outer bearing parts must match those in the original hub in order for the replacement hub to fit properly on the trailer spindles.
I linked for you our main page for trailer hubs. You can click on the... view full answer...
The Air Lift Ride Control Air Helper Springs item # AL59529 for Chevrolet S-10s have an air pressure range of 5 psi - 100 psi. The psi will be determined based on your comfort desire and the weight of the load being put on your S-10.
I recommend adding the Air Lift WirelessAIR Compressor System for Air Helper Springs - Remote - Bluetooth - EZ Mount item # AL74000EZ. Air Lift's premium, wireless, onboard compressor system with Bluetooth allows you to fill your air springs at the touch of... view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver # 65004 referenced in your question is confirmed to fit your 2001 GMC Sonoma.
While I wasn't able to obtain complete installation specs for the model grille guard that you mentioned, looking at pictures of its mounting hardware and design, it certainly appears that it should fit without issue alongside a front-mounted hitch like this on your GMC Sonoma. I do recommend verifying this by taking a look at the installation instructions for... view full answer...
You are correct, the Roadmaster vehicle-specific Base Plate Kit, part # 161-2 is the correct base plate kit for your 2003 GMC Sonoma.
In addition to the base plates and tow bar, you'll need safety cables, a wiring solution and a supplemental braking system. For safety cables, I'd recommend the # RM-643 from Roadmaster. for lighting, a magnetic mount kit like part # RM-2120 would be simple to install and would not require any of the existing wiring on the vehicle to be altered. A supplemental... view full answer...
Jets adjust the fuel/air mixture for proper combustion, regardless of the fuel source. To use your Firman 3,300-Watt Portable RV Dual Fuel Inverter Generator # FIR54FR in 5,000' to 6,000' elevations you'll want to install part # 333-330717002. view full answer...
Hey David,
The Curt Front Mount Trailer Hitch Receiver # 31180 is only designed to fit a 2001 - 2007 Toyota Sequoia and a 2000 - 2006 Toyota Tundra.
Since you have a 1996 GMC Sonoma you need the Curt Front Mount Trailer Hitch Receiver # 31021 which is a custom fit so you don't need to do an drilling or cutting to get it installed. view full answer...
Go To Results