Expert Answers about Nissan Sentra dimensions

Expert Answers about Nissan Sentra

Dimensions of the CE Smith Fender Brackets # CE26098G-2
On the CE Smith Fender Brackets # CE26098G-2 the long side of the bracket is 8-1/4 inches, the shorter side of the bracket is 6-1/2 inches, the bracket is an 1-1/2 inch in width, on the shorter side the holes of the bracket measure 4 inches, on the shorter side the holes measure 2-3/8 inches, each hole is 3/8 of an inch thick. I attached a video that shows all of these measurements being taken.
view full answer...

Recommended Hitch for a 2015 Nissan Sentra SV
The best hitch for your 2015 Nissan Sentra SV is going to be the Curt Trailer Hitch item # C11349. This hitch is custom fit and bolts to your Nissan with included hardware. I checked with Curt and confirmed that this hitch does fit the SV models. The Curt Trailer Hitch item # C11349 is a class I hitch with a 1-1/4" receiver. It is our highest rated hitch for your car and it has a 2,000 lbs towing capacity and a 200 lbs tongue weight. I have attached a picture below along with the instructions...
view full answer...

What is Roof Rack Capacity for Extended Thule Canyon XT for 2017 Nissan Sentra
The weight capacity for the Thule roof rack part # TH859XT-8591XT that you referenced which is a fit for your 2017 Nissan Sentra 4-door is 150 lbs. With just this part number you'd have the a complete roof rack with the extension. You'll also want to check the roof capacity of your Sentra and be sure not to exceed that figure as well. Basically the lowest rated component of the setup is the overall capacity.
view full answer...

Highest Capacity Trailer Hitch Receiver for 2017 Nissan Sentra
The highest capacity trailer hitch receiver for a 2017 Nissan Sentra is 2,000 lbs towing and 200 lbs tongue weight (please keep in mind there are no fits for a Sentra SR) the Draw-Tite Trailer Hitch Receiver # 24907 and Curt Trailer Hitch Receiver # C11349. You mentioned 103 kg (227 lbs) and neither of these hitches will be able to utilize a motorcycle and carrier with that much weight, and there isn't a hitch available for your Sentra that will allow you to use a carrier. The only option...
view full answer...

Height of Curt Trailer Hitch C11349 For 2016 Nissan Sentra
Definitely can help you out here and the height from the ground to the top of the receiver on your 2016 Nissan Sentra will be approximately 10 inches for the Curt hitch you asked about, which is the following part number: - Curt Trailer Hitch Receiver # C11349 The actual height should be very close to that once you install the hitch, but could vary based on a number of factors, like tire pressure or size, etc. So I do recommend installing the hitch first and measuring it and the coupler...
view full answer...

Yakima Roof Rack and Carriers to Transport 2 Kayaks on 2014 Nissan Sentra
The Yakima round bar roof rack system made of parts # Y00408, # Y28TR, # Y03536, # Y06123 and # Y06170 is a confirmed fit on your 2014 Nissan Sentra and its 165-lb weight rating makes it suitable for transporting two typical kayaks. I have linked an installation video to illustrate that process. It is a good idea to check your Sentra owner's manual to make sure Nissan rates the roof with enough capacity for the actual weight of your two particular kayaks, plus the weight of the roof rack...
view full answer...

Tongue Weight and Towing Capacity of Draw-Tite Class I Receiver Part # 24794
The folks at Draw-Tite assure me that the Class I receiver you mention, part # 24794 is rated at 200 lb tongue weight/ 2000 lbs towing. This has been confirmed through extensive testing. You will want to check your owners manual to determine the actual towing capacity of the vehicle, and abide by whichever figure is lower. If you were planning on using the hitch for towing a small utility trailer, you might also need the following: A ball mount Wiring harness with 4-pole trailer connector,...
view full answer...

Distance from Center of Hitch Pin Hole to Tab in Shank on Draw-Tite Class I Trailer Hitch # 24907
Draw-Tite is actually going to stop including that tab on Class I hitches like # 24907. But on the ones that still have it the distance from the center of the pin hole to the tab is 1-7/8 inches so your ball mount will not fit. The recommended ball mount for this hitch is # 3593 and it includes a pin and clip. I have linked a video review of it for you.
view full answer...