The 525 lb max tongue weight and 3,500 lb max gross trailer weight rating is what the # e98848 is capable of. Many aftermarket Class III hitches are able to handle more weight than the vehicle they are designed for. Occasionally the towing capacity of the vehicle exceeds the capacity of the hitch. Whatever the case may be, you are always limited by the lower capacity. In this case, you are limited by the weight capacity listed in your 2024 Honda CR-V owner's manual. view full answer...
I went to our warehouse and measured the Buyers Products 50 Ton Air Compensated Pintle Hook # 337PH50 to get the height dimensions. The overall height of the pintle when open is 12" and when closed is 9-1/2". I also took a measurement for the height from the center mounting hole which you can have as reference point if your recessed area already has the holes drilled. When open it is 9-1/4" to the top of the hitch and 6-1/2" when closed. I have included images below with these measurements... view full answer...
According to Maxtrax, the mounting holes on the # MA24ZV are 10" on center across the width of the board and 25" lengthwise. All of the mounting pins like # MA48PR use M10 bolts so you will need to drill an appropriate hole based on the type of mounting surface.
I attached a link to all of the mounting hardware below for your reference. view full answer...
Hi Brian,
The Putco Stainless Steel Fender Trim for Ford F-150 # P97220 is tapered at the ends so the width starts at 2" in the middle and thins down to 1-1/2 at each end. view full answer...
There's unfortunately not a guide to tell us the sizing of your trailer's jack pads so you'll want to measure and note the shape of each pad. I've run into numerous situations where the front and rear pads were either different sizes or shapes to work with the space available.
The SnapPad # SN88FR you were looking at are designed to fit four 9" round pads and two 12" round pads. If you can let me know what your shape and dimensions are I'd be happy to pick out the correct package. view full answer...
The 30" Slipper Spring # e89SR is our longest 4-leaf spring. I might be able to help you change out your springs with a different size that are more easily found if you can send me some images of your suspension setup with measurements from the hangers. view full answer...
I don't see why the Trailer Axle with Idler Hubs # e25GR wouldn't work with a 3" c channel trailer frame. You'll just want to make sure that the hub face to hub face on your current axle is 60", and your spring seat to spring seat is 48".
Also, this axle will work with 8" to 14" wheels, has a 2,000 lb capacity, a 1 3/4" diameter, and has a 4 on 4 bolt pattern. view full answer...
Hey Marc, I contacted Buyers Products was able to get that measurement for you, and the distance is 2-3/4 inches from the center of the hitch pin to the gusset on the Buyers Products 2" Pintle Hook Mount # 337PM812.
For a compatible pintle hook and hardware use Pintle Hook # 337PH6 and # 3378520. view full answer...
That was enough information right there. If it is welded to the axle a modern replacement won't work. Unless you can find parts at a scrap yard you won't be able to get replacement parts for those brakes to rebuild them either. You will need to replace the axle like I mentioned before.
You need the same length axle you have now, which is the hub face to hub face measurement, along with the same capacity. You can try to see if there is an axle tag on there identifying it. If not, it might... view full answer...
Hey Steve, so between the hitches that fit your 2022 Jeep Wrangler Sahara the etrailer part # e98856 and the Curt # C13392 have the exact same dimensions, and the Draw Tite part # DT78MR is slightly different.
The only real difference is the length of the hitch tube. The Curt/etrailer sticks out a little further whereas the Draw Tite is a litte more recessed. From the end of the hitch tube to the first mounting flange the Draw Tite sticks out 6-1/2 inches whereas the Curt/etrailer has... view full answer...
With trailer tires you want to inflate them to the max psi figure when cold to ensure you get the full weight capacity and you don't create excessive heat build up due to sidewall flex. view full answer...
Thanks for the info and photos, Joe!
From what I'm seeing in your photos it looks like the Mini-Illuminated 12V Switch # 37212765 could be a great option for you.
The switch measures 1-1/4" tall x 3/4" wide x 3/8" deep and fits a cutout of 3/4" tall x 1/2" wide. If this matches what you have then you'll be good to go! Otherwise Let me know what the dimensions of are your switches you need to replace and let me know what you have so I can compare that with our selection. view full answer...
Hey Jeff; thanks for the question and there is really just one option to carry your heavy ebikes in the bed of your 2022 Ford F-150, and that's with a tailgate pad bike rack:
- Thule GateMate Pro Tailgate Pad for Full-Size Trucks # TH824PRO
All other truck bed racks have weight limits which your 75 lb bikes far exceed, which is why the pad is the only way to haul the bikes. It does have soft foam padding for cushioning your bikes and straps to prevent them from moving as you travel. view full answer...
Hello Alicia. The cam arm on the Camco Cam Lock # CAM44323 is 2" long overall so it should work well for you. I have attached some more detailed dimensions below for your reference. view full answer...
Brendon, you'd need to measure your current rail length and width and take note of what the shape is. For instance, if you measured your current rail was in an H shape and measured 93 1/2" long, 2" tall, and 1 1/2" wide, then # 36281-955 would work. view full answer...
The Aries Step Pad replacement part # AA2090133 is the same dimensions as what you have now but when we measured it we found it to be 23-1/2 inches long and 4 inches wide. view full answer...
Hey Paul, thanks for reaching out!
The bolt holes for the Draw-Tite Class V Trailer Hitch Receiver # DT45502 are spaced out 35-1/2" on center for the width, and then for the back to forth dimensions we're looking at 3-3/8" for the holes closer to each other (on either end) and then 7-7/8" for the middle holes.
I've attached some dimensional photos for your reference. view full answer...
Hello. I was able to get the measurement for the Fulton Round Snap-Ring Swivel Marine Jack # FTJ12000101 that you requested. It is 9-3/4" from the center of the bracket to the bottom of the wheel when retracted. I made I diagram for your reference. view full answer...