Because trailer wiring harness # 118551 requires a direct connection to the vehicle battery, the power wire will be energized all the time because it is connected to the battery. However, with nothing drawing power on the 4-Way end that power has no where to go (nothing is drawing it). So just having the harness installed cannot drain the battery unless something is plugged into the 4-Way and is drawing power.
If you have the power wire connected anywhere other than the vehicle battery... view full answer...
We offer a security strap to help deter theft of trunk-mount bike racks like the Hollywood Racks # HRF2 and # HRF2-3. That item is # TH533. If you want something more secure you could use a cable lock like # e98891 to lock the rack to a rear tow hook for example. You can also use the cable lock to secure the bikes to the carrier when they are loaded for travel. view full answer...
Locating your problem will require some troubleshooting.
You will first need to determine if the problem exists with the vehicle wiring or with the trailer wiring. Typically, the problem occurs on the trailer. To rule out the vehicle, start by using a circuit tester like part # PTW2993 on the trailer connector on the vehicle, as each function is being operated. Have a helper activate the left turn signal, then test the pin on the connector that corresponds with the yellow wire. Activate... view full answer...
If you tested the wiring on your 2008 Mercury Mariner and it is operating properly but then when you install a wire converter unit the 4-Way flat connector isn't operating properly then yes, I would say that is an indication of a faulty converter/ModuLite wiring unit. In this case I recommend replacing your wiring with the T-One # 118551 as it sounds like you don't have the factory tow package.
I really like the Tekonsha wiring kits because we tend to have the fewest amount of troubleshooting... view full answer...
We don't have a video showing the install of the Curt # 31650 on a 2010 Mercury Mariner, but we can still provide assistance. The installation is pretty straightforward, with the only twist being the need to use the included bolt leaders to pull some of the installation hardware into the frame.
I can link you to the installation instructions, as well as to a video that shows how to use a bolt leader to pull the installation hardware into the frame members. To install the hitch, you'll... view full answer...
The two Lippert Trailair 5th wheel pin boxes LC155933 and # LC158777 are actually one and the same part. The old part number LC155933 has been replaced by the new item reference # LC158777. This air cushioned pin box is a direct bolt-on replacement for the Lippert 1716 5th-wheel pin box and it is rated for 21,000-lbs.
The Trailair will reduce chucking, bounce and jarring thanks to its internal air spring and shock system which absorbs these forces to give you a smoother and more stable ride. view full answer...
I have a solution for you, but the Valley Wiring harness part 30130 has been discontinued. For a very similar wiring harness confirmed to fit your 2006 Mercury Mariner I would recommend the Tow Ready Harness part # 118551. This harness is available and would work well. I attached an install video for you to check out as well. view full answer...
I reviewed the installation instructions for Curt Class III Hitch, part 13650, and spare tire removal is not mentioned. You should be able to retain the factory spare in the original location on a 2005-2010 Mariner. I have added a link to the instructions below for you to review as well as a link to a basic pin and clip, part # PC3, and a basic hitch lock, part # e98880. view full answer...
There isn't anything from the dealer you will need to install an electric brake controller on your 2011 Mercury Mariner.
Since you already have a 4-way trailer connector all you need to add is our installation kit # ETBC7. This will provide you with the 7-way trailer connector, as well as the wiring and circuit breaker needed to install a brake controller. I've attached a video of the # ETBC7 being installed on a 2011 Ford Escape which will be the same process as your Mariner.
If you... view full answer...
The Curt T-Connector Vehicle Wiring Harness, part # 118551, will work on your 2008 Mercury Mariner Hybrid whether or not it has the factory tow package.. I am including a link to the installation instructions and a video link to the wiring harness being installed on a 2007 Mercury Mariner. view full answer...
Yes, If your 2008 Mercury Mariner has the factory cross bars that run from side to side on the top of the vehicle, the SportRack J-Stacker Kayak Carrier - Roof Mount, item # SR5511, will work on your vehicle. The J-Stacker will work on factory cross bars up to 3-1/2 inches diameter.
If your vehicle has factory side rails that run front to back, without cross bars, you will need cross bars. I would recommend the Thule Roof Rack For 2008 Mariner by Mercury, which consists of part # TH712100... view full answer...
Vehicles using trailer wiring harness # 40455 may need to see a local Ford or Mazda dealer for a relay. The relay is needed to activate the tow package wiring circuit. It sounds like your 2007 Mercury Mariner is missing that relay. Also check to make sure that the trailer side connector is clean and free of corrosion because that can cause lights to not work. view full answer...
The presence of the back-up sensors will not have any bearing on the installation of a hitch. The Curt # 13650 would be an excellent choice that would work well for you. This hitch will fit whether or not your vehicle is equipped with the OEM 1-1/4 inch receiver.
The fact that your Mariner has the back up sensors will mean that you'll need to use the # 118551 trailer wiring harness, if you'll be towing with your Mariner. It's been found that the # 118251 doesn't work on vehicles with the... view full answer...
Yes, the Thule Hullavator Pro # TH898 can fit on the Malone Square bar roof rack part # MPG201 you have on your 2006 Mercury Mariner. Thanks for the kind words on our site! view full answer...
It sounds like your installed might be describing a universal type-converter that needs to be hardwired into the vehicle.
We offer the Tow Ready Custom Fit Wiring, # 118551, which is a powered unit and requires you to run a power wire to the battery, which helps isolate the vehicle wiring from any short circuits that might occur in the trailer wiring. This harness installs inline with the taillight wiring, and other than having to run the power wire, is a plug-and-play install.
A quote... view full answer...
You indicate your Mariner did not come with a hitch. According to Ford's website, that means it is not wired for towing either. Product number 118251 is for vehicles with a towing package, so it will not work for your vehicle.
You will need product number 118551, a wiring harness with a 4 pole trailer connector for your Mariner. This wiring harness may be used with 5-pole, 6-pole, or 7-pole adapters. This is a custom fit wiring harness for your Mariner.
I will attach a wiring FAQ and... view full answer...
With the Taskmaster 4.80/4.00-8 Bias Trailer Tire # AM30000 having a diameter of 16.1 inches when fully inflated, we will not have a perfect fit for a cover. The closest we will have will be the CE Smith Spare Tire Cover # CE27410, but this will fit tires up to 21 inches in diameter, so it will be very loose and will need modifications to fit snuggly.
We do also have the Classic Accessories RV Wheel Covers # CA80098, which technically isn't a spare tire cover, but can also be modified... view full answer...
The WeatherTech Black Cargo Liner, # WT40197, fits your cargo area behind the 2nd row (last row) of seats. The measurements are hard to be specific on because it is a custom fit product. It comes rolled up, so it is hard to measure but here is what I found.
From front to rear the mat measures 36-1/2 inches, from side to side, in the back of the vehicle, the mat measures 48 inches, and between the wheel wells the mat measures 40-1/2 inches. Again these measurements are approximate but should... view full answer...
If your 2005 Mercury Mariner has side curtain air bags then you will want to install tracks # THTP54 further in (towards the middle) on the vehicle roof to avoid interference. The wiring for things like the dome light are more or less in the center of the vehicle so you would not worry about that unless you wanted to put tracks in the middle of the roof.
To avoid drilling you could use a custom roof rack using the following parts:
CrossBars # INB137
Feet # INSUT
Fit Kit # INK193 view full answer...
Yes, the Weather Tech Easy-On Stone and Bug Shield Deflector # WT50185 that you referenced is designed to fit all model 2008 Mercury Mariners including your hybrid so it should work well for you.
I attached installation instructions for you to check out also. view full answer...
Go To Results