The Curt Trailer Hitch Receiver # C11145 has a bolt hole separation of 5-7/8" on center. I have included a picture for you as well for this measurement.
I have also linked the installation instructions below. view full answer...
I attached a page that has all of the confirmed trunk mounted bike racks we offer for your 2000 Acura Integra 3 door. The most popular one we carry is the Thule Passage part # TH910XT. I attached a review video for this rack for you to check out. For the money you can't really beat this rack. It has anti-sway cradles and adjustable arms so that you can carry the bikes as level as possible.
If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may... view full answer...
Draw-Tite trailer hitch # 24589 does also fit the sedan models of the 2000 Acura Integra! If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.
I have linked the Class I compatible 2-bike racks and cargo carriers for you. view full answer...
For your SportRack Semi-Custom Roof Rack for Naked Roofs - Square Crossbars - Steel - 45-1/2" Long # SR1003, you will need the Replacement Lock Cylinder for Thule Racks and Carriers - N038 # THLOCKN038 to match your key. view full answer...
Yes, this Draw-Tite Sportframe Trailer Hitch Receiver # 24589 is confirmed to fit Acura Integras from 1994 to 2001 so it would work well on your 1997 Integra. I attached installation instructions for this product for you to check out also.
You may be interested in the following products to complete your towing setup:
Tow Ready Custom Fit Vehicle Wiring # 118336 (installation instructions and review video attached)
Sportframe Drawbar # 3593
1-7/8 in Ball # 19256
Pin and Clip # PC2 view full answer...
The only available trailer wiring option for your 1991 Acura Integra would be the Upgraded Circuit Protected Taillight Converter Hardwire Kit, # 119175KIT. There is no T-one plug and play style harness for your vehicle. Installation of the 119175KIT is actually pretty easy, even with little experience.
I have included a couple of videos showing typical installations of this wiring harness. Basically, all you will need to do is to access the wiring behind each tail light. Using the included... view full answer...
The correct trailer wiring harness for your 1991 Acura Integra Hatchback, is the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester # 119178KIT. This harness adds a 4-way trailer connector on your Acura Integra. The harness splices into your existing wiring. The surface mount technology construction ensures superior performance.
I attached installation instructions and a video to assist. view full answer...
The SportRack Semi-Custom Roof Rack you mentioned, part # SR1008 is compatible with your 1991 Acura Integra if it is a 4 door model. If you have a 2 door model, then you will also want to pick up the SportRack Short-Roof Adapter part # SR1116.
Thule has a ski carrier, part # TH32WV as well the roof mounted bike carrier, part # TH598004.
SportRack does not offer a fairing, so I asked my Thule representative if any of the Thule fairings would be compatible with the SportRack Frontier roof... view full answer...
The Yakima Roof Rack in the video you referenced has been discontinued by the manufacturer. If you have the double cab, then I recommend the following parts for a Yakima roof rack: # Y00426, # Y28TR, # Y06125, and # Y06128. The locks to secure this are # Y07204.
This roof rack could be used in conjunction with a truck bed ladder rack like the Thule Xsporter part # TH500XT for your 2013 Toyota Tacoma. This is an adjustable height ladder rack that will let you perfectly match up the height... view full answer...
I did some research on your Giant Talon 1, and since the top of the bike's frame slants down toward the seat, it will attach onto the arms of the Thule Apex XT 2 # TH9024XT with a Hollywood Racks Bike Frame Adapter Bar for Women's and Alternative Frame Bikes # HRBA-PRO. The bike frame adapter will give your frame a straight horizontal mounting point that will work with the cradles of the Apex XT 2.
The only thing to note is the 37.5 per-bike weight capacity of the Apex XT 2. Based on the... view full answer...
The item you selected, T-One Vehicle Wiring Harness, part # 118336, is the correct wiring you will need for your 2001 Acura Integra GSR.
You will need to access the vehicle wiring connector located at the rear of vehicle behind the plastic trim panel. Make sure the tabs on the connector lock in place for a complete connection. You will then secure the black box and tuck the wiring. Then re-install the plastic trim and panel and test the connector using a circuit tester, part # PTW2993.... view full answer...
It looks like there are no longer any trailer hitches that fit your 2000 Acura Integra. The Curt Trailer Hitch Receiver 11147 was discontinued this year (2023) so you might try searching to see if you can find that hitch elsewhere, otherwise I recommend installing a roof rack in order to add some cargo-carrying capacity to your vehicle (if that's what you're needing to do):
Sedan
- 42" Square Crossbars # INB107
- Feet for Square Crossbars # INSUT
- Fit Kit # INK130
Hatchback
Same parts,... view full answer...
The 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles # e69SR should be compressed ~2" under a 1,000 lb load which would make the "F" measurement ~1 3/4" with the 1,000 lb load. This is based on a formula to find spring compression since we don't actually have that info at hand so take it with a grain of salt. view full answer...
It sounds like there is a ground issue in the wiring, probably on the trailer side, but it will be a good idea to check all of the grounds to make sure. Start with the white ground wire from the converter box of # 119178KIT. Make sure it is attached to a clean and corrosion free bare metal surface on the vehicle.
Next, check for any dirt or corrosion in the vehicle and trailer side connectors. You can then move on to the trailer side. Check the main ground coming from the trailer side... view full answer...
The Yakima Replacement Lock Housings for Q Towers, # Y8870069, do not include the lock cylinders or keys.
For the added lock cylinders and keys, you will need the Yakima Same Key System Lock Cores, # Y07204, to add to the lock housing # Y8870069. These lock cores are keyed the same. Once installed, you will only need one key to lock or unlock each core.
The cores will include 2 keys and a master key to allow you to remove and install the lock cores into the lock housings. view full answer...
I was not able to find the particular specifics on the 1995 Acura Integra LS regarding to put it in par or nuetral when dolly towing, however our Roadmaster Dolly part # RM-2050-1 instructions state Put front wheel drive vehicles in park. If it is a rear wheel drive, make certain it can be pulled with the rear wheels on the ground without damaging the transmission. If it can be safely towed, put the towed vehicle in neutral. If not, remove the driveshaft and put in park (in gear if a manual... view full answer...
As long as clearance isn't an issue you can certainly do away with the existing 90-degree fitting like what's included with # BH-3MFS90-1-5 and go with a straight fitting right to the caliper instead. We do have a shorter 1 foot brake line available with the Kodiak part # BH-3MFS-1. This flexible rubber line features 3/16 inch brass fittings on each side and the hose itself has a 1/8 inch inner diameter.
I have attached a short video review that you can check out as well. view full answer...
Yes, this Draw-Tite Sportframe Trailer Hitch Receiver # 24589 is confirmed to fit Acura Integras from 1994 to 2001 so it would work well on your 1998 Integra. I attached installation instructions for this product for you to check out also. The hitch opening will sit right under the rear bumper fascia of your vehicle so you would need to measure the current distance from the lowest portion of the rear fascia then subtract 2 inches and you will have about how much ground clearance you would... view full answer...
There are no plug-in style trailer wiring harnesses for the 1991 Acura Integra. To wire your vehicle for towing, you would need to hardwire the connector into the existing lighting circuits. We offer a Taillight Converter with 4 pole Connector, which also includes an installation kit. The part number for this kit is part # 119178KIT.
The converter would attach to the existing tail light circuits in your Integra. The easiest place to access this wiring would be behind the taillight assemblies.... view full answer...
We do offer roof rack options for your 2000 Acura Integra Hatchback.
Inno offers a custom fit rack which consists of these parts:
• 42 inch square crossbars, part # INB107
• Roof rack feet for square bars, part # INSUT
• Short roof adapter, part # INJK
• Vehicle-specific fit kit, part # INK130
SportRack offers a semi-custom rack option, which would be made up with these parts:
• Semi-Custom rack, part # SR1003
• Short roof adapter, part # SR1116
If I had to choose between the two,... view full answer...
Go To Results