Replacing Hydraulic Brake Line and 90-Degree Fitting on Trailer
Question:
Im replacing the lines on my trailer and the 90-degree fitting is pretty rusted and beat up looking. I was wondering if I could do away with that fitting and run this line directly to the caliper. If not, is the 90-degree fitting sold separately, and do you guys sell a small 1 foot piece of hose to go between the caliper and the T going to the other wheel?
asked by: Mike
Expert Reply:
As long as clearance isn't an issue you can certainly do away with the existing 90-degree fitting like what's included with # BH-3MFS90-1-5 and go with a straight fitting right to the caliper instead. We do have a shorter 1 foot brake line available with the Kodiak part # BH-3MFS-1. This flexible rubber line features 3/16 inch brass fittings on each side and the hose itself has a 1/8 inch inner diameter.
I have attached a short video review that you can check out as well.
Products Referenced in This Question
Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1'
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 1 Foot Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Kodiak
more information >
Product Page this Question was Asked From
Kodiak Hydraulic Brake Hose - Straight and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Accessories and Parts
- Brake Actuator
- Trailer Brakes
- Disc Brakes
- Hydraulic Drum Brakes
- 1-1/2 Feet Long
- Brake Lines
- Flexible Brake Hose
- Brake Line Components
- Kodiak
more information >
Continue Researching
- Shop: Bearing Kit, 15123/ 25580 Bearings, 10-36 Seal
- Search Results: kodiak 225 brake caliper
- Shop: Kodiak Disc Brake Kit - 12" Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Shop: Fulton Boat Trailer Jack w/ Footplate - Fixed Mount - 28" Lift - Zinc - 5,000 lbs
- Video: Kodiak Trailer Brakes - Disc Brakes - K2R526D Review
- Q&A: Availability of Side Frame Mount Jack for Aluminum Trailer With 3 x 6 Frame
- Q&A: Mounting Bracket Bolt Hole Dimensions for the Fulton Marine Jack part # HD50000101
- Q&A: Recommended Trailer Jack For Aluminum Trailer With 5-1/2 Inch I-Beam Frame
- Q&A: Available Replacement Parts for Tie Down Engineering LP7000 Actuator
- Q&A: Torque Settings For Wheel Lug Nuts For Boat Trailer And utility Trailer
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1'
- Q&A: Recommended Plug Covers for a Roadmaster EZ-5 Baseplate for a 2021 Chevy Spark
- Shop: Kodiak Hydraulic Brake Hose - Straight and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Q&A: Replacement Flexible Brake Line Hose for a Trailer with Torsion Axles
- Shop: Kodiak Hydraulic Brake Hose - FIF and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Shop: Grease Seals 10-36 (pair)
- Shop: Base Plate for Tow Bar
- Video: Kodiak Hydraulic Brake Hose Review and Installation
- Article: How to Bleed Your Trailer Surge Brakes
- Video: Review of Lippert Replacement Level Up Leveling System - LC58TF
- Search Results: kodiak 250 calipers
- Search Results: brake line hose
- Search Results: lippert wheel bearings
- Search Results: wheel bearings
- Video: Review of Kodiak Trailer Brake Parts - Brake Hose 1.5 Foot - BH-3MFS90-1-5
- Video: Best 2021 Chevrolet Spark Flat Tow Set Up RM-523202-5
- Video: Review of Lippert Components - Battery Boxes - LC366510
- Video: Bleeding Brakes Demonstration