Expert Answers about Suzuki Equator

Does the Trailer Wiring Harness # 56087 Require the Factory Tow Package on a 2011 Suzuki Equator
The CURT Custom Fit Trailer Wiring Harness, item # 56087, does not require the factory tow package for installation. This harness plugs inline with the existing tail light wiring harness on the vehicle. I have provided a link to instructions for you to review. If your vehicle does have the factory tow package wiring, then you could use the Replacement OEM Tow Package Wiring Harness, item # 118263, on your vehicle. I have linked instructions for this harness also.
view full answer...

Back Up Alert Recommendation for a 2010 Suzuki Equator with a # 921 Reverse Lamp Bulb
The Hopkins Backup Alert, # HM20101VA, is designed to replace a # 3156 bulb and will not replace the # 921 bulb on your 2010 Suzuki Equator. Instead, I would recommend looking at the Custer Surface Mount Back-Up Alarm, # BK97DB. This alarm can mount to any surface such the frame or bumper and wires into the reverse light circuit on your truck. Once it is wired in it will send a 97 decibel alert when the truck is placed in reverse.
view full answer...

Tap To Clean Weld Nuts Inside Frame On a Suzuki Equator
Yes, we have the 12 mm x 1.25 Tap and Drill Bit part # PTW8662 which can be used to clean the weld nuts inside the frame when installing a trailer hitch on a Suzuki Equator.
view full answer...

Will the Curt Wiring Kit # 56087 fit on a 2011 Suzuki Equator without Tow Package
The harness you found is the correct one, thank you for sending that picture, that eliminates all guesswork. You can use the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 56087 on your 2011 Suzuki Equator without a tow package. The wiring is available on all model vehicles. I attached installation instructions for this product that you should check out also.
view full answer...

Parts Needed to Install 7 way Connector on 2009 Suzuki Equator
In order to add a 7 way connector to your 2009 Suzuki Equator, you can simply use the # ETBC7, which will utilize your existing 4 way. You won't need to replace the existing harness, but once you plug it in to the ETBC7 you'll need to run a wire to your battery to supply 12v power and one to your brake controller to complete all of the circuits on the 7 way connector. I've linked a basic installation video of this connector that you can use as a guide. When it comes to the towing capacity...
view full answer...

Trailer Brake Lights/Turn Signals Not Working when Connected to 2009 Suzuki Equator
To determine if there is a problem on the harness or on the trailer here is what you will need to do. Disconnect the trailer from the truck. Then use a circuit tester, like # PTW2979 if needed, to test the pins on the 4-Way end of wiring harness # C56225. If the brake and turn signals are working at the 4-Way then you know the problem is on the trailer. If they are not working on the 4-Way and you are certain that everything is installed correctly according to the instructions, linked...
view full answer...

Troubleshooting Trailer Brakes That Stay Locked Up
I suggest disconnecting the trailer to allow you to test the wiring on the vehicle independent of any potential issues on the trailer. You will need a circuit tester like # PTW2993 or a multi-meter like # PT89ZR. First, test the 7-way. The brake circuit is carried on the pin at the 5-o-clock position (see photo please). If your controller is set for zero power and zero boost, in other words powered up but with no output level, you should detect close to 0 volts on the pin. If you detect...
view full answer...

Trailer Wiring Harness on 2012 Suzuki Equator is Not Working
According to my contact at Curt, the # 58067 isn't the correct wiring harness for a 2012 Suzuki Equator, which would explain why it's not functioning correctly. The correct wiring harness for your Equator is the Curt # C56225, which includes all the relays needed to activate the tow package.
view full answer...

What is the Length of the Suzuki Trailer Hopkins Wiring Harness part # HM43575?
The Hopkins wiring harness item # HM43575 has a length of 45-1/4 inches for the wiring alone and the overall length including the plugs/adapters end to end is 48-1/8 inches.
view full answer...

Comparing Curt Wiring Harnesses for a 2011 Suzuki Equator
The Curt trailer wiring harness, # C56225, works and installs more like the factory one if the vehicle had a factory tow package. There is a jumper plug that you will connect at the front of the vehicle and another harness that plugs in at the back. it also includes 3 relays which the factory tow package would include. I have included a link to the installation details for you. The Curt harness, # 56087, plugs in line with the tail light wiring and draws all of the power through the tail...
view full answer...

Ball Mount Recommendations for a 2011 Suzuki Equator
The recommended ball mount for the hitches for the 2011 Suzuki Equator is a Ball Mount # AMSC2. The etrailer.com Ball Mount Kit # 989900 that you referenced includes the # AMSC2 as well as a Ball Mount # 2753 that has a 2 inch greater drop. I also includes a 2 inch ball and a 1-7/8 inch ball that way if you had two trailers that have different coupler sizes you could just swap ball mounts and be good to go. I also attached an FAQ article on ball mounts for you to check out.
view full answer...

Transmission/Engine Oil Cooler Recommendation for a 2009 Suzuki Equator
The best way to pick out a transmission cooler is to measure the area in front of the radiator and pick out the largest cooler that will fit in that area. If you have room for it the Derale Combination Transmission and Engine Oil Cooler with Multiple Threads # D15902 would be an excellent choice for your 2009 Suzuki Equator. This would work as a transmission cooler as well as an oil cooler. This unit measures 17" Wide x 12-1/2" tall x 3/4" deep. I attached installation instructions plus...
view full answer...

Does Factory Installed Transmission Cooler on 2011 Suzuki Equator Mean I Have Tow Package w/ Wiring
If your 2011 Suzuki Equator is equipped with the tow package, you should have a 4-way or 7-way connector at the back of the vehicle. Having the factory installed transmission cooler doesn't always guarantee that your vehicle is equipped with the tow package. If your Equator does not have a connector, most likely there is a black and a grey plug that is mounted on the driver's side frame rail back by the rear bumper and you will need to install a wiring harness. You will need the Curt T-Connector...
view full answer...

Troubleshooting Trailer Brakes that Lock Up when Trailer Wiring is Connected
You have a short between the brake output circuit and the 12 volt accessory circuit. That's what's putting 12 volts on your trailer's brakes at all times when connected. You'll want to go over the wiring of the trailer looking for any exposed wires touching each other or corrosion and fix as needed. It's also possible that the 7-way is incorrectly wired. I attached a picture that shows how a 7-way should be wired by function.
view full answer...

Where Should the Converter Box be Mounted on a 2011 Suzuki Equator Trailer Wiring Harness
If you look at the instructions, linked for you, for the CURT Wiring Harness, # 56087, they have attached the converter box to the frame rail on the 2011 Suzuki Equator. You will want to make sure the frame rail and converter are clean by using a 50/50 alcohol and water mixture. Let them dry before securing the converter to the frame with the included sticky tape. You can use a Mounting Bracket 4-Pole Flat, # 18144, with # C57202 or # 18140 to secure the 4-Way plug. I have included a...
view full answer...

Are Relays Needed to Activate Tow Package Wiring in 2012 Suzuki Equator
If the 4-pole connector you speak of was factory installed, everything should already be functional. If you've just installed a 4-ploe, using a part like # 118263, then the relay kit # C57000 would be needed. The brown relay activates the 12-volt circuit to the trailer connector (which you won't need since you have a 4-pole) and the two blue relays activate the right and left turn signal and brake lamp. Since you mentioned that you got a signal at the trailer connector with the turn signals,...
view full answer...

Trailer Wiring Recommendation for a 2012 Suzuki Equator
We do have a wiring harness designed for your Equator but I spoke with my contact at Curt Manufacturing and found that the custom fit wiring, # 56087, is not recommended for the 2012 Suzuki Equator. Since your Equator is not equipped with the factory tow package you will need the wiring harness with relays and a 4-Way flat trailer connector, # C56225. This kit will activate the tow package wiring that is present in your vehicle wiring harness. To install the Curt wiring on your vehicle...
view full answer...

Troubleshooting Non-working Running Lights on a Trailer Being Pulled by a 2012 Suzuki Equator
To determine if the issue is on the vehicle or the trailer you will need to disconnect the trailer and use a circuit tester such as # PTW2993 to test the vehicle side connector. With the running lights on, test the pins on the vehicle side connector. If there is no power at the connector, then the issue is on the truck. If there is power at the vehicle connector, then the issue is on the trailer. You can check to see if the tow package fuses and relays are present or just bad by using...
view full answer...

Dimensions of Putco Tailgate Cap 51614P
I reached out to the manufacturer and the Putco Tailgate Cap - Stainless Steel # P51614P measures 50.25 inches long. He didn't have a width and we don't have one to measure ourselves so all I can give you is that he says it will cover the top side completely. This Product Fits The Following Vehicles: 1988 - 2000 Chevrolet C/K Series Pickup 6-1/2 Foot Bed - Stepside 1988 - 2000 GMC C/K Series Pickup 6-1/2 Foot Bed - Stepside 1988 - 2000 GMC C/K Series Pickup 8 Foot Bed
view full answer...

Curt Trailer Wiring Harness Recommendation for a 2011 Suzuki Equator
The Curt Custom Fit Vehicle Wiring # 56087 that you referenced will work on your Suzuki Equator even if you do not have the tow package. This product plugs in line with your tail light harness on your vehicle and is not dependent on whether or not you have a tow package. The easiest way to determine if your vehicle has a tow package would be to contact a Suzuki dealership and give them your VIN number, from that they should be able to tell if you have the tow package. Typically, tow packages...
view full answer...