Expert Answers about Nissan Armada

• Where Does a Brake Controller Wiring Harness Install on a 2012 Nissan Armada
• To install the Curt trailer brake controller wiring harness # C51382 you will need to locate the factory harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. I have linked a video and some instructions on another harness that fits that should help. The Curt trailer brake controller wiring harness is compatible with Curt brand brake controllers that accept the plug, like the Echo Under-Dash # C27JR....
  view full answer...


• How to Install Brake Controller Wiring on a 2004 Nissan Armada
• You are looking for a 6 pin connector located near the emergency brake pedal. It is usually taped to another wiring harness. You will need a wiring adapter, part # 3050-S to complete the connection.
  view full answer...


• Where is the Relay Located for the Running Lights on a 2006 Nissan Armada SE
• First, for a 2006 Nissan Armada, you would use wiring harness and relays # N40975. Harness # C56225 that you referenced is not a fit for the Armada. I have included a link to a video showing a typical installation. On some Nissan vehicles an additional relay is needed next to the steering column under the dash. It will be a small blue relay. You can obtain the relay from the dealer or use one of the blue ones in kit # C57000. Consult the vehicle owner's manual for all fuse/relay locations...
  view full answer...


• Can Side View Cameras of Furrion Vision S Wireless Always Stay on
• So long as you wire the side view cameras to the running light circuit, they will stay on continuously when using the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras # FCE48TASL-05. When wired this way, the side cameras of the Vision S # FCE48TASL-05 won't just come on when the turn signals come on, and the monitor even has a tri-view display option so you can see both on the sides and behind you.
  view full answer...


• How to Get the Air Tubing Out of Spring in Firestone Coil-Rite Air Springs F4150
• Where the 3 inch tubing meets the air spring in kit # F4150 there is a collar that holds in the tubing. Push that collar towards the air spring and you will be able to pull out the tubing with your other hand. The little collar holds the tube in by compression. Pushing it in towards the spring releases the tension.
  view full answer...


• Installing The Tekonsha P3 Brake Controller In A 2017 Nissan Armada Using the Plug-In Wiring Adapter
• If your 2017 Nissan Aramada is the same as the Infinity QX80 as you referenced, then the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti # 3050-P will connect to the brake control wiring harness underneath the dash to the left of the steering column. It is taped to another harness near the emergency brake pedal. This harness will allow you to easily install your Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional, # 90195
  view full answer...


• Why Does Auto-Leveling System on 2018 Nissan Armada Need to be Disabled to Use Equal-i-zer System
• I would be happy to help you figure out how to setup an Equal-i-zer weight distribution (WD) on your 2018 Nissan Armada towing your Jay Flight 26BH. Equal-i-zer states that auto-leveling systems should be disabled when using their WD systems because the auto-leveling feature can actually end up working against the WD system and change (likely decrease) the effects of the Equal-i-zer system. If you have aftermarket air bag suspension then they state to inflate the air bags to the desired...
  view full answer...


• Does ground for ETBC7 Kit Need to be Installed if 4-Way on 2017 Nissan Armada is Already Installed
• Yes you still need to ground the white wire for the Wiring Kit # ETBC7 because there are some additional functions that come with the 7-Way plug. You can actually use the same ground point that you used for your Vehicle Wiring Harness Kit # C59496 if it is nearby, otherwise you'll need to find another suitable location for this second ground.
  view full answer...


• Brake Controller for 2009 Nissan Armada with Factory 7-Way
• Since you had all the wiring and circuit breakers needed for brake controller installation on your 2009 Nissan Armada installed by the dealer, the only thing you need to do is plug in the brake controller. It comes with what you will need to mount it (bracket and screws). All that is left is to plug the adapter, included with the Tekonsha P2 Proportional Brake Controller with Nissan Adapter, # 90885 and # 3050-P, into the brake controller and vehicle. The harness on your 2009 Nissan Armada...
  view full answer...


• Is Factory Style 7-Way and 4-Way Connector 30608 Compatible With the Prodigy Brake Controller 90185
• Yes, the factory style 4 and 7-Way connector # N40975 would be a perfect pairing with the Prodigy P2 brake controller # 90885. You would simply plug the # N40975 connector into the factory socket you found near the driver side frame rail. The included relays would need to be installed in your relay panel, which would be located on the passenger side, near the battery. The Prodigy P2 brake controller # 90885 and wiring adapter kit # 3050P would be used to complete the installation....
  view full answer...


• Can the Gen-Y 10 Adjustable 2-Ball Mount Be Used for Towing and a Hitch Carrier
• The Gen-Y Adjustable 2-Ball Mount part # 325-GH-325 can be used for both towing and hitch mounted accessories at the same time. That said, the ball mount would likely need to be in one of the bottom two holes with the hitch mounted accessory in the top. In regards to weight, it has a very high 1,500 lb rating so as long as the tongue weight of the trailer and weight of the hitch mounted accessory are below this you will be fine. It's built like a tank so you should not have any concerns...
  view full answer...


• Installation and Adjustment of Husky Centerline Weight Distribution Hitch HT32217
• If your Husky Centerline weight distribution hitch (WDH) model # HT32217 is not leveling your 2018 Armada you'll want to confirm that it is rated correctly for the actual total tongue weight (TW) of your towing system and that it is set up correctly. You may care to check out the linked demo video. This particular WDH works with trailer TW from 600 to 800-lbs. You can measure your loaded trailer's TW using scale # e99044. To your measured trailer TW you need to add the weight of any cargo...
  view full answer...


• Adding a 7-Way Trailer Connector and Brake Controller to 2008 Nissan Armada without Factory 7-Way
• If your 2008 Nissan Armada did not come with a factory trailer connector then you can add one by first installing a 4-Way flat connector, # C59496, and then installing Brake Controller 7- and 4-Way Installation Kit # ETBC7. There isn't a kit that plugs in for models that did not come with the factory 7-Way so that is why this hardwire method is needed. I have included some links that show and explain the ETBC7 installation for you. If your trailer has electric brakes that you want to use...
  view full answer...


• Which Wire Is Power vs. Ground When Installing the 2-Wire Plug for MC 65 Series Clearance Lights
• On the Black Bracket with 2-Wire Plug for MC65 Series Clearance Lights # A68PB, I've attached a video to assist in showing you ground and power. If you have the light facing you with the wires to the left, the top wire will be power and the bottom will be your ground.
  view full answer...


• What PSI Should My AirBags Be At When I Am Not Pulling A Trailer?
• When not towing/pulling anything with your Nissan Armada, the Firestone Coil-Rite Air Helper Springs - Rear Axle # F4150 should be inflated to a minimum of 5psi to prevent the bags from deforming without any air in them. When towing, you want to start inflating the bags according to how much your vehicle is sagging at the rear, and stop inflating when the vehicle is at its normal ride height. Remember to never exceed 35psi with this system. I attached a helpful demonstration video for you.
  view full answer...


• How to Wire a Tekonsha Voyager Brake Controller # 39510 to a 2012 Nissan Armada
• You're very close, to see how your Tekonsha Voyager part # 39510 should install to the factory wiring of your 2012 Nissan Armada check out the chart I attached that shows how it all connects. The red/blue wire you found will not be used, that is the third brake light circuit and is not needed. The B+ wire SHOULD be a red wire and will be the 12 volt circuit and would get run to the black wire of your controller.
  view full answer...


• Locating an Installer For Air Bag Helper Springs For a 2023 Nissan Armada
• Below the product images for the Firestone Coil-Rite Air Helper Springs # F4150 which fits your 2023 Nissan Armada you will find a link "Locate installers near me". This will allow you to search for installers along your route to determine which one will be able to help you during the timeframe you need. I recommend also installing the Air Lift WirelessAIR Compressor System # AL58WQ when you install the air springs. This compressor includes a smart manifold which will allow you to make...
  view full answer...


• How to Determine Wire Harness Functions for Brake Controller Wiring on a 2017 Nissan Armada
• I can help you determine what wire on your harness is for which function, but unfortunately we don't know what color wire holds what function on your 2017 Nissan Armada. What you will need to do is use a circuit tester like part # PTW2991 and test your wiring harness. You will be able to find 2 of the functions easily. One will have constant power and one will only have power when you press your brake pedal. This leaves you with the ground wire and the wire that sends power to your trailer...
  view full answer...


• Does Curt Front Hitch for 2019 Nissan Armada Need to be Removed When Changing Oil
• The Curt Front Mount Trailer Hitch Receiver # C31081 will not have to be removed when changing the oil on your 2019 Nissan Armada. When the hitch is in place you will still be able to remove (and re-install) the factory skid plate, which is what needs to be taken off when changing the oil on this vehicle. I have attached a full installation video below that you can use for reference, along with the written install manual.
  view full answer...


• Where Is The Factory Trailer Brake Controller Port Located On A 2015 Nissan Armada?
• The factory trailer brake controller port on your 2015 Nissan Armada should be located underneath the dash right above the brake pedal. When we installed a different trailer brake controller on a similar 2018 Nissan Armada we found that the connector was taped up with black electric tape which can make it a little tricky to find. Take a look at the included video at the 4:00 minute mark as it shows exactly where the connector will be. Once you find the connector you can then plug in the...
  view full answer...