I pulled up the owners manual of your 2007 Pontiac Vibe and to tow it on a tow dolly like the # RM-2000-1 you need to put the transmission in park if it's an automatic or neutral if it's a manual. Clamp the steering wheel in the straight ahead position using the seat belt wrapped around the wheel a few times and then buckled. Next you'll pull the belt all the way out so that it engages the ratchet mechanism and you'll then pull it as tight as you can to the wheel so that the belt is locking... view full answer...
I checked with Thule and the Gateway Pro 2 Trunk Mounted Bike Carrier # TH88VR that you referenced is confirmed to fit your 2009 Pontiac Vibe. I have linked you to a demonstration video featuring the Gateway bike rack.
The best way to prevent theft of a trunk mounted bike rack is to have it installed only when you are transporting bikes and then remove it when you are parked and are away from your vehicle. Any time an accessory like a bike rack is in direct contact with a painted portion... view full answer...
Since you would be right at capacity I do recommend taking any measures feasible in lightening the load. That will make it that much easier on the vehicle. I do believe that properly equipped, the 2009 Pontiac Vibe will be fine towing the 1,500 pounds. Since you will not constantly be towing it up a steep ramp, and that aspect is only a small part of the journey, the Vibe should be just fine.
For a trailer hitch, you can use # C12221 but it is for GT models. If you have a GT model then... view full answer...
To add a 4- and 7-Way connector to your 2005 Pontiac Vibe that already has a 4-Way AND to have it work with the Prodigy RF # TK94FR you will need a couple of parts. First you will need # 37185. The 4-Way you have plugs into this, retains the 4-Way and also adds a 7-Way.
This adapter has several wires that you will need to hardwire to the vehicle so that it will work with the RF. First, ground the white wire to the frame. Since you are using the Prodigy RF you will not need the blue wire... view full answer...
For a canoe carrier that would allow you to transport it with the hull facing down on the Yakima Rack and Roll Trailer part # Y08107 that you referenced you would want the Yakima KeelOver Rooftop Canoe Carrier with Tie-Downs # Y04069. This rack is designed for transporting a kayak or canoe with the hull facing down.
Check out the review video I attached for more info. view full answer...
Transmission coolers are not vehicle specific, however to optimize efficiency you would want to use the largest transmission cooler available, and mount in the optimal place on your vehicle. The most efficient mounting position is considered to be between the grille and the AC condenser core.
Considering the space that is available for you to mount a transmission cooler is most likely limited on your 2006 Pontiac Vibe I recommend either the Derale 9000 Plate and Fin Transmission Cooler... view full answer...
Yes, it is possible, with certain exceptions. The Tow Ready adapter # 80303 should help you in most instances. The hitch I recommend is the Draw-Tite # 24812 Class II.
Please bear in mind, even if you adapt a 1-1/4" tube to fit 2" accessories, there are still limitations that will apply. Using the adapter will reduce the weight capacity of the hitch by 50% in terms of both tongue weight and gross trailer weight. In this instance, the Class II hitch that fits your Vibe will be limited to... view full answer...
Since only Class II and up trailer hitches can carry 4 bike racks the hitch you would want is the Curt hitch part # C12234 which is a confirmed fit for your 2007 Pontiac Vibe. The other hitches you mentioned are Class I which can only carry up to 2 bikes on a bike rack. view full answer...
We have many bike racks that will fit on a 2005 Pontiac Vibe. The two different styles would be a trunk bike rack and a hitch bike rack. The trunk design bike rack will use straps to clamp to the rear hatch of your vehicle. A hitch design bike rack will insert into a hitch on your vehicle so it will require a hitch to be installed on your vehicle.
For a trunk bike rack I would recommend the Yakima HangOut 3 Bike Rack, part # Y02638. This bike rack has lot of extra features like the one... view full answer...
For a base plate kit confirmed as a fit for your 2006 Pontiac Vibe the Roadmaster XL kit part # 3130-1 is a confirmed fit that would work well with your Roadmaster Falcon part # RM-520. view full answer...
There are 2 possible trailer wiring options for your 2005 Pontiac Vibe GT. The Tow Ready Custom Fit Vehicle Wiring, # 118458, that you have referenced would be the easiest to install. It has 3 sets of connectors and a ground wire. The 3 sets of connectors simply plug in line with your vehicle tail lights. The ground wire gets connected to a bare metal surface or existing ground point.
To get access to the connection points, you will need to remove the rear cargo area floor panel (as if... view full answer...
For a great quality base plate for your 2005 Pontiac Vibe, I recommend the Blue Ox Base Plate Kit - Removable Arms # BX3224. The Blue Ox plate comes with a custom-fitting that will be able to attach to the front of your vehicle. It also includes a straightforward installation with no welding necessary.
If you need a tow bar to go along with the base plate, I recommend the Blue Ox Acclaim Non-Binding Tow Bar - Car Mount - 2" # BX4330. The Acclaim will fit with the Blue Ox Base Plates without... view full answer...
The flat towing products mentioned in the question you read will fit your 2007 Pontiac Vibe, you will more than likely need a lube pump or a drive shaft disconnect since your Vibe is an automatic. Unfortunately I am not able to confirm which components would be required.
An easier option that absolutely works is Dolly Towing, and this option will not require any modifications to your vehicle.
I recommend going with the Roadmaster Tow Dolly with Electric Brakes - 4,250 lbs # RM-2050-1... view full answer...
When using a weight distribution system on a trailer the weight on the axles will stay the same. The tongue weight of the trailer will be distributed from being basically all on the rear axle of the tow vehicle to being also on the front axle of the tow vehicle.
Weight distribution systems are recommended when the trailer of the vehicle weighs more than 50 percent of the tow vehicle.
The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of... view full answer...
The powered converter on the Hopkins Plug-In Simple Vehicle Wiring Harness # HM11141425 and the Curt T-Connector # 55057 will require a direct connection to the vehicle battery to power the trailer lights. This will essentially protect the vehicle wiring and electrical system from damage. Because these harnesses use a powered converter, it will have a higher amperage rating when compared to alternatives that have a standard converter.
With this in mind, if you only plan on towing a trailer... view full answer...
There are indeed a few trailer hitches available that are confirmed to fit your 2008 Pontiac Vibe. Since you do not have the GT model, I recommend going with the Curt Class II Round Tube Receiver Hitch # C12234. This Class II hitch is custom-fit for your vehicle and will use existing holes in the Vibe's frame for a no-drill installation. It will provide a 1-1/4 inch receiver opening and has a 200 pound tongue weight capacity. It features a sleek, round tube design and has a gloss black... view full answer...
I checked with Saris and the Bones 3 Carrier part # SA801BL has been confirmed as a fit for your 2010 Pontiac Vibe.
However, for a rack that would work better with the spoiler of your GT you would want the Hollywood Rack Over the Top part # HRF2. This rack is specifically designed to fit over spoilers like what you have.
If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Swagman Easy-Out Women's and Alternative... view full answer...
For a base plate kit for your 2005 Pontiac Vibe the Roadmaster XL part # 3130-1 has been confirmed as a fit and would work well.
In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle. The most popular compatible tow bar is the Falcon 2, # RM-520. For safety cables you can use # RM-643. The coiled design helps keep the cables off of the ground.
For lighting you can use the diode kit, # RM-15267,... view full answer...
The Curt Wiring Harness part # 55057 that you referenced is the correct wiring harness for your 2003 Pontiac Vibe. This unit should do very well to power and operate the taillights of a Yakima Rack and Roll trailer like part # Y08107.
The trailer will pull about 9 amps total, whereas the # 55057 is good for 6 amps per circuit. Which is more than enough. view full answer...
2 inch hitches are only used on larger vehicles like trucks and SUVs that have higher towing capacities. For your 2003 Pontiac Vibe you would have to go with a 1-1/4 inch hitch like the part # 24812 and a bike rack compatible with a Class I hitch like this.
The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I... view full answer...
Go To Results