The MaxxAir Standard RV and Trailer Roof Vent Cover # MA00-933066 is a standard cover that fits most vents with the standard 14" x 14" dimensions. If you can give me some more details about you current vent (with photos) I can look into this fitment a little more for you.
In the meantime I've linked a review video here for you to check out. view full answer...
Yes, the Advent Air RV Air Conditioner # ACM135 will work great as a direct replacement for your Coleman Mach 10 air conditioner.
With the use of the Coleman adapter # ACCOLKIT wiring harness, you will be able to use your existing air distribution box and thermostat.
Additionally, to further improve the performance of this air conditioner, you can use a Start Capacity for Advent Air RV Air Conditioners # ACMSCKIT. What this does is use the stored energy to jumpstart the air conditioner,... view full answer...
The Pop&Lock # PAL9772 will fit a hard fiberglass tonneau cover that meets the following parameters:
• Fits fiberglass tonneau covers on vehicles with power door locks
• Tonneau cover must have a 1-1/8" center hole for a rotary latch
• Tonneau cover must have a cable-latch assembly
If your Unercover Lux bed cover meets those stipulations, the # PAL9772 will work. view full answer...
Look at your landing gear and find out the height of the outer tube, typically it's the black tube. That will let you know which jack you should go with. Then find the distance between the weld stops. This will let you know if the jack will fit or it you'll need to cut off and reweld on the brackets.
If the distance between weld stops is 15-1/2" then this set # RVLG-8000 would work for you. view full answer...
We have two center caps that will work with a Lionshead Liger 15" rims. I have listed them below:
Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 4.25" Pilot - Stainless Steel item # LHCS108-SI60C
Replacement Center Cap for 15" or 16" Aluminum Viking Series Wheels - Gloss Black item # CXF104B view full answer...
I recommend confirming that the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System # LC672136 will fit on your 2021 Palomino Puma 26RLS by checking the placement on the rear jacks. Since these jacks may need to install in a different location than the electric stabilizers that you currently have the system may not fit your Puma. Your current stabilizers are mounted closer to the rear of the trailer and the center of the jacks need to have at least 9-1/2" vertical... view full answer...
The Furrion System you referenced the FOS43TADS no longer has a camera option that is compatible or you could indeed sync a second camera. You will need to upgrade the system at this point to the VIsion S system # FOS43TASF you asked from and then you can add the Furrion Vision S Wireless RV Backup Camera w/ Night Vision - Rear Mount - Black - Qty 1 # FCN48TASF for that second camera. view full answer...
Thank you for the photo, which has your axle's capacity at 4,400 lbs; what that means is the correct self-adjusting trailer brakes are the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4,400 lbs # K23-478-479.
If instead you were referring to brakes which are manually adjustable then you would need the Dexter Electric Trailer Brake Kit - 10" - Left and Right Hand Assemblies - 4,400 lbs # K23-462-463-00; you would also need the Brake Adjustment... view full answer...
According to all my research, a 2014 Palomino Sabre 33-RETS or 33-RETS-6 measures 35 feet, 1 inch. I recommend verifying within your owner's manual or the manufacturer what your exact length is just to be sure, but everything I found point to it being 35 feet, 1 inch, and for that the correct UltraGuard cover is the following:
- Camco UltraGuard 5th Wheel Cover - 36' Long # CAM45756 view full answer...
We may have an option for fenders for your 2019 Solaire 268 BHSK, though there are no custom-fit replacements available for your trailer. Based on my research it looks like this is a tandem axle trailer with 15 inch wheels, and we do have fenders for that size trailer. What you will want to do is measure your current fenders and get replacements that match up to the size as much as possible, and use your existing hardware to bolt them on. They can also be painted to match whatever color... view full answer...
I can confirm that the Classic Accessories Deluxe PolyPro III Heavy-Duty Pop-Up Camper Cover # CA80043 is a fit for your 2017 Paolmino 12 STS camper.
I have added a link to a video review for you to check out as well of the Classic Accessories Deluxe PolyPro III Heavy-Duty Pop-Up Camper Cover # CA80043. view full answer...
If you have a cover like the part number 4140155 that you have provided, that is a 14" x 14" so this low profile metal cover # BV0534-00 is 14-1/4" by 14-1/4". The extra 1/4" is just from the 1/8" lips on each side. view full answer...
Prewiring can mean a lot of different things since there's no industry standard on that term so you'll first want to see what you have available first. In my experience this typically just means that the manufacturer just ran the AC power to junction box in that area and cut a hole for the ac unit to fit into.
If you have a controller there then you could get away with just purchasing a rooftop condenser unit like the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup -... view full answer...
I am not able to look up parts number for AL-KO axles as they are no longer in business but I can see it has a 2,100 lb weight capacity which means it will likely use L44649 bearings. Therefore, the correct bearing kit should be the Bearing Kit part # BK1-150. view full answer...
With installing the Road Armor Shock Absorbing Equalizer # LC696740 you will want to use the MORryde Suspension Upgrade Kit # MR76ZR on your 2014 Palomino Puma 19RL travel trailer. These shackles are longer at 3-1/8" on center to account for the additional height of the Road Armor Equalizer. To help strengthen the suspension I recommend adding the MORryde X-Factor Crossmember # MR33WR for each set of hangers. This will strengthen the hangers by connecting them together across the trailer. view full answer...
Based on my research, your 2016 Palomini 179 BHS travel trailer has a 3,885 lb GVWR and a single Dexter Torflex axle; I do recommend verifying that but based on that we do have the correct lift kit for your trailer:
- Torflex Lift Kit - Single Axle # K71-707-01
This lift kit is a fit for #10 Torflex axles with 2,300 to 4,000-lb capacities, so you will want to double check the sticker on the axle to ensure there is a number 10 on it, but it is highly likely. With this kit your Palomino... view full answer...
My research shows that the 2014 Palomino Banshee B-2 weighs about the same as the 2013 models, both of which weigh about 3,600lbs with a tongue weight of about 360lbs. The Reese Pro Round Bar Weight Distribution w Sway Control - Round Bar - 6,000 lbs GTW, 600 lbs TW # RE34FR you were looking at would be a great option!
This weight distribution hitch is more than capable of handling your Banshee travel trailer and limits sway so you won't be fighting to keep the trailer in line with your... view full answer...
Based on my research your 2020 Palomino Puma 286RBSS 5th Wheel has axles that are in the 6,000 lb range, which means they should be 3 inch diameter round axles, though I highly recommend verifying this. Also make sure the suspension on your Palomino is double-eye spring suspension, and if so, because it is a tandem axle trailer you will need two of the Dexter Trailer Springs Over-Under Conversion Kit # K71-385-00.
I have added a link to a video review of this kit for you to check out as well. view full answer...
Blue thread sealer can be used but you run the risk of it clogging the line if it spreads out from the threads to the tip of the fitting. It's safer to just use thread sealant tape like # 37207-30025 to avoid any clog issues. You would not want to use thread sealant on flared fittings since they'll have a gasket to prevent leaks. view full answer...
The short answer to your question is, yes. You can use the Curt Safety Chain Quick Link # C82932 to keep your current safety chains in good working. The safe working load limit that you see on products like the Curt Safety Chain Quick Link # C82932 has to do with everyday use. So, if you were to use this quick link to regularly pull something Fulton doesn't recommend exceeding 3,300 lbs (6,600 lbs for 2 of them).
Since you're looking to use these for your trailer safety chains you need... view full answer...
Go To Results