Expert Answers about Nissan Armada
- Does ground for ETBC7 Kit Need to be Installed if 4-Way on 2017 Nissan Armada is Already Installed
- Yes you still need to ground the white wire for the Wiring Kit # ETBC7 because there are some additional functions that come with the 7-Way plug. You can actually use the same ground point that you used for your Vehicle Wiring Harness Kit # C59496 if it is nearby, otherwise you'll need to find another suitable location for this second ground.
view full answer... - Does Weight of Yakima LockNLoad Platform Rack Count Against Roof Weight
- If your vehicle has a 100 lb roof weight capacity the weight of the Yakima LockNLoad Platform Rack for Crossbars # Y05044-39 would count against that. So you'd have a total of 57 lbs of cargo weight you could carry.
view full answer... - Adding a 7-Way Trailer Connector and Brake Controller to 2008 Nissan Armada without Factory 7-Way
- If your 2008 Nissan Armada did not come with a factory trailer connector then you can add one by first installing a 4-Way flat connector, # C59496, and then installing Brake Controller 7- and 4-Way Installation Kit # ETBC7. There isn't a kit that plugs in for models that did not come with the factory 7-Way so that is why this hardwire method is needed. I have included some links that show and explain the ETBC7 installation for you.
If your trailer has electric brakes that you want to use...
view full answer... - Installing The Tekonsha P3 Brake Controller In A 2017 Nissan Armada Using the Plug-In Wiring Adapter
- If your 2017 Nissan Aramada is the same as the Infinity QX80 as you referenced, then the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti # 3050-P will connect to the brake control wiring harness underneath the dash to the left of the steering column. It is taped to another harness near the emergency brake pedal.
This harness will allow you to easily install your Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional, # 90195
view full answer... - How to Wire a Tekonsha Voyager Brake Controller # 39510 to a 2012 Nissan Armada
- You're very close, to see how your Tekonsha Voyager part # 39510 should install to the factory wiring of your 2012 Nissan Armada check out the chart I attached that shows how it all connects.
The red/blue wire you found will not be used, that is the third brake light circuit and is not needed. The B+ wire SHOULD be a red wire and will be the 12 volt circuit and would get run to the black wire of your controller.
view full answer... - Parts Needed to Install Brake Controller in 2017 Nissan Armada
- You should be able to install the Tekonsha Voyager brake controller part # 39510 in your 2017 Nissan Armada with the install harness part # 3050-P and the 7-way install kit part # N40975 as our understanding is that every Armada in 2017 came wired for this setup.
Other option is to hardwire the brake controller with first wiring in a 4-way like part # C59236 and then using the kit part # ETBC7 to adapt this 4-way to a 7-way and allow you to hardwire in the controller. Check out the install...
view full answer... - Does Curt Front Hitch for 2019 Nissan Armada Need to be Removed When Changing Oil
- The Curt Front Mount Trailer Hitch Receiver # C31081 will not have to be removed when changing the oil on your 2019 Nissan Armada. When the hitch is in place you will still be able to remove (and re-install) the factory skid plate, which is what needs to be taken off when changing the oil on this vehicle.
I have attached a full installation video below that you can use for reference, along with the written install manual.
view full answer... - Where is the Best Place to Install a Remote Transmission Cooler on a 2017 Nissan Armada
- As far as functionality there isn't one place that is really better than another for the Derale Atomic-Cool Remote Transmission Cooler Kit # D13950 on a 2017 Nissan Armada. Basically anywhere there is space for it will be a good location. On modern vehicles space in the engine compartment can be at a premium though so you will want to check ahead of time prior to installing a cooler.
This cooler is 12-3/4" wide x 9-3/8" tall x 4-5/16" deep overall. The width and height probably won't be...
view full answer... - How Does Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 Install
- The Atwood RV Carbon Monoxide and Propane Gas Detector # AT36681 was designed to fit into a cutout like what the picture I attached shows. The wires on the back would prevent it from being able to mount flush.
Wall cutout size: 3-9/16" long x 3-7/16" wide x 1" deep
view full answer... - Installation and Adjustment of Husky Centerline Weight Distribution Hitch HT32217
- If your Husky Centerline weight distribution hitch (WDH) model # HT32217 is not leveling your 2018 Armada you'll want to confirm that it is rated correctly for the actual total tongue weight (TW) of your towing system and that it is set up correctly. You may care to check out the linked demo video.
This particular WDH works with trailer TW from 600 to 800-lbs. You can measure your loaded trailer's TW using scale # e99044. To your measured trailer TW you need to add the weight of any cargo...
view full answer... - Tekonsha Voyager Brake Controller Doesn't Have Lights When Not Connected to Trailer
- The green light on the Tekonsha Voyager Trailer Brake Controller # 39510 will only come on when a trailer with properly functioning brakes is connected. The light will turn red when either the brake pedal is pushed or the manual operation lever is used.
I have included a link to the instructions below that includes troubleshooting in case you have an issue when you do connect to the trailer.
view full answer... - Will a 130 Amp Alternator Cause Problems with 10 Amp Rating of Battery Isolation Solenoid
- As long as you install the Battery Isolation Solenoid, # PK5231201, correctly (see photo) and the items you are powering on the battery isolator output circuit does not draw more than 100 amps you will not have any problems.
In most cases the battery isolator is installed on the charge line going to a trailer connector at the back of a vehicle and this circuit is used to maintain the trailer batteries charge and/or power utility lights in or on the trailer. In this situation your alternators...
view full answer... - How to Install Brake Controller Wiring on a 2004 Nissan Armada
- You are looking for a 6 pin connector located near the emergency brake pedal. It is usually taped to another wiring harness. You will need a wiring adapter, part # 3050-S to complete the connection.
view full answer... - Can Side View Cameras of Furrion Vision S Wireless Always Stay on
- So long as you wire the side view cameras to the running light circuit, they will stay on continuously when using the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras # FCE48TASL-05.
When wired this way, the side cameras of the Vision S # FCE48TASL-05 won't just come on when the turn signals come on, and the monitor even has a tri-view display option so you can see both on the sides and behind you.
view full answer... - Where on 2012 Nissan Armada is the Blue Relay Located
- The blue relay from the Curt Relay Kit for Nissan # C57000 is a replacement running light/turn signal relay for Nissan trucks and SUVs for trailer lights and tow package. One of the blue relays installs in a box under the driver-side dashboard to the left of the steering column.
This kit includes a brown relay to activate the 12-volt power circuit and two blue relays to activate turn signals. The linked video shows installation in a 2008 Armada.
view full answer... - Which Wire Is Power vs. Ground When Installing the 2-Wire Plug for MC 65 Series Clearance Lights
- On the Black Bracket with 2-Wire Plug for MC65 Series Clearance Lights # A68PB, I've attached a video to assist in showing you ground and power. If you have the light facing you with the wires to the left, the top wire will be power and the bottom will be your ground.
view full answer... - Where Is The Factory Trailer Brake Controller Port Located On A 2015 Nissan Armada?
- The factory trailer brake controller port on your 2015 Nissan Armada should be located underneath the dash right above the brake pedal. When we installed a different trailer brake controller on a similar 2018 Nissan Armada we found that the connector was taped up with black electric tape which can make it a little tricky to find.
Take a look at the included video at the 4:00 minute mark as it shows exactly where the connector will be.
Once you find the connector you can then plug in the...
view full answer... - Curt Spectrum Brake Controller Install 2018 Nissan Armada with Factory Tow Prep
- In order to use your Curt Spectrum Trailer Brake Controller part # C51170 in your 2018 Nissan Armada you need the Curt Custom Wiring Adapter part # C51382. One end plugs into your Spectrum Brake Controller while the other plugs into the factory harness located under the driver side dash, to right side of the steering column and above the accelerator. I included a photo of another brake controller harness being plugged into a similar Armada and some video reviews of the brake controller...
view full answer... - Is Factory Style 7-Way and 4-Way Connector 30608 Compatible With the Prodigy Brake Controller 90185
- Yes, the factory style 4 and 7-Way connector # N40975 would be a perfect pairing with the Prodigy P2 brake controller # 90885.
You would simply plug the # N40975 connector into the factory socket you found near the driver side frame rail. The included relays would need to be installed in your relay panel, which would be located on the passenger side, near the battery.
The Prodigy P2 brake controller # 90885 and wiring adapter kit # 3050P would be used to complete the installation....
view full answer... - What PSI Should My AirBags Be At When I Am Not Pulling A Trailer?
- When not towing/pulling anything with your Nissan Armada, the Firestone Coil-Rite Air Helper Springs - Rear Axle # F4150 should be inflated to a minimum of 5psi to prevent the bags from deforming without any air in them. When towing, you want to start inflating the bags according to how much your vehicle is sagging at the rear, and stop inflating when the vehicle is at its normal ride height. Remember to never exceed 35psi with this system. I attached a helpful demonstration video for you.
view full answer...
Go To Results