The MagnaFlow Ceramic Catalytic Converter # MF444105 that you referenced fits 3.5L V6 models of the Nissan Altima. The converters we offer for your car with the 2.5L inline 4 can be seen on the link provided. Some of these are universal-fit types that weld on, such as # MF99205HM, while others are direct fit, such as # MF93287. Note that some of these do not have an O2 port.
A 2-inch-diameter flex-joint should work as long as that is the dimension of your exhaust tubing. view full answer...
This Swagman bike carrier, part # S64670, is intended for use on vehicles that have a trailer hitch receiver installed under the rear bumper. (It is a hitch-mount type bike carrier.) If your Altima does have a hitch receiver, such as the Curt Class 1 Hitch for the 2006 Nissan Altima, part # C11264, you can use this type of rack.
You can check underneath your rear bumper to see if there is a 1-1/4 inch square opening visible in the center; this would be the hitch receiver opening into... view full answer...
The Yakima SweetRoll Kayak Carrier # Y04074 will fit onto the SportRack Roof Rack # SR1010.
The SportRack will fit on your 2016 Nissan Altima however it's a semi-custom fit so it's not designed specifically to fit the roof of your car. For a custom fit I suggest the Yakima Roof Rack:
48 inch Round CrossBars # Y00408
BaseLine Towers # Y28TR
RoundBar Adapter # Y03536
BaseClip Fit Kits # Y06137 and # Y06127 view full answer...
You may see some rise in the rear of your 2009 Nissan Altima when you add the Firestone Coil-Rite Air Helper Springs # F4105. It really depends on if you already have additional weight on the rear end and if your springs are worn. With new springs and no additional weight you are less likely to see any rise in the rear suspension but as the bag pushes into the coils it will allow some of the sag to be relieved and raise the height on worn springs.
The Air Command Compressor System # F2610... view full answer...
Since we have determined that the Sportrack hitch locks fit the Curt bike racks like the # C18084 that you referenced we can confirm that the Sportrack hitch lock and anti-rattle cable part # A32022 will work as well. view full answer...
I am happy to confirm that yes, you can use the Curt Chrome 2" Hitch Ball # C40018 you asked about with the Curt Class II Drawbar # C45521.
These two parts are completely compatible, and also keep in mind you will need either a pin and clip or hitch lock to secure the ball mount to your hitch receiver. For that you will need either Curt Class I and II Pin and Clip # F-4 or Curt Trailer Hitch Receiver Lock # C23517.
I have added links to some video reviews for you to check out as well. view full answer...
The Derale Series 8000 Plate-Fin Transmission Cooler Kit part # D13501 would be a good size for a 2007 Nissan Altima so this is what I recommend. It comes with everything that you need for installation as well. I can't really speak of this vehicle or transmission combo specifically but reducing the transmission fluid temperature via a more efficient transmission cooler will help prolong the life of the transmission. view full answer...
The Swagman XC Bike Rack, # S64650, should be able to hold a townie bike, but to be absolutely certain that this bike rack will support your bike, we will want to take a few measurements on your bike.
First, this bike rack can support a wheel base up to 51-1/2 inches long. To find the wheel base on your bike, measure from the center of the front wheel axle to the center of the rear wheel axle. Next, you will want to find the width of your tires. The wheel loops on this rack can support... view full answer...
The tab on the inside of the trailer hitch receiver for your 2008 Nissan Altima is meant to ensure that the user only uses Class I rated accessories in the hitch. As you can see in the attached photo.
This is more of a safety precaution as Class I receivers like # 24796 cannot handle much weight especially if that weight is sticking out further from the receiver. It could damaged the receiver and ultimately damage your accessory (in this case your bike rack and bike).
To answer your... view full answer...
The correct grease seal you need for your 1999 Bass Tracker Pro Team 175 should be part # 10-9. This seal has a 1.500" inner diameter and a 1.987" outer diameter. I would measure the outer diameter of your existing grease seal to be certain you receive the correct replacement. view full answer...
Due to the weight of your 2021 Specialized como 4.0 step over E-BIke of 48lbs you will need to use a platform style rack like the Thule EasyFold XT Bike Rack # TH903202. The Yakima FullBack 2 Bike Rack # Y02634 only allows for two bikes that weighs 35lbs each. Even by only carrying one bike you would still exceed the single bike weight rating for the rack and its components that hold each bike in place. It also looks like the battery only weighs about 8lbs so that would still not decrease... view full answer...
The Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets # D13503 is designed as a supplemental transmission cooler, but should work well as the only transmission cooler in your 2006 Nissan Altima with a 2.5 liter engine. This is a pretty heavy duty, efficient cooler that should have more than enough cooling capacity for your vehicle.
Check out the installation video and FAQ articles I attached on transmission coolers also. view full answer...
Yes, the Rhino-Rack Ski and Snowboard Carrier # RR576 will fit and work great for the Rhino-Rack square crossbars on your 2016 Nissan Altima! This carrier comes with a locking system for the skis/snowboards and uses a unique Allen wrench for the mounting hardware so you have some added peace of mind. view full answer...
We do have a fit for your 2011 Nissan Altima sedan; I checked with the manufacturer and can confirm that the correct fit is the Curt Trailer Hitch Receiver # C11352.
I have added a photo a customer sent in of this hitch installed on his Altima with a double exhaust as well so you can see how it will look on yours.
If you plan on doing some light towing with your Altima you will also need the T-One Vehicle Wiring Harness # 118470, Curt Drawbar # C45521, Pin and Clip # F-4, and 1-7/8" Hitch... view full answer...
The correct replacement hub/drum for the Roadmaster Tow Dolly with Electric Brakes (RM3477) part # RM-2050-1 is the Dexter Trailer Hub and Drum Assembly part # 84546UC3-EZ. This is a complete kit and what I recommend using to get back up and running.
The retainer or cotter pin likely came out causing the castle nut to back off and that is what caused the hub to become loose. There could have been damage to the hub or bearings and races which is why I recommend a full replacement. view full answer...
The Firestone Coil-Rite Air Helper Springs # F4105 that you referenced will give you additional support for the rear suspension of your 2010 Nissan Altima. If you inflated them enough it would prevent the suspension from traveling as far as normal over bumps which would stop the rubbing you are experiencing.
Too much air pressure will cause the ride quality to be harsh, so your best option would be to experiment with different air pressures till you find one that will prevent the rubbing... view full answer...
If there was a 2 inch hitch for your 2011 Nissan Altima I'd love to recommend one but unfortunately that is just not something that exists. That size hitch is not made for an '11 Altima so if you want to use a hitch and hitch mounted bike rack with this vehicle you'd have to get a 1-1/4" Class I hitch and compatible bike rack. The hitch that fits is the following:
- Curt Trailer Hitch Receiver # C11352
Then for a Class I bike rack that will work you can use the Kuat Beta # B202-114 or... view full answer...
If the Saris bike rack does have a threaded hitch pin hole, then only a Saris threaded hitch pin will fit. Each company makes their threaded parts unique so only their parts are compatible with each other.
If the Saris rack does not have a threaded hitch pin, you could most likely use the Hollywood Racks 2" Hitch Lock and 8' Cable Lock for Bike Racks # HRLHPC2 for the non-threaded pin and cable lock. If you just want a cable lock, you can use # e98891. For a 1-1/4 inch receiver hitch... view full answer...
Go To Results