All of the our Solera Slide Toppers like the part # LCV000163287 that you referenced require at least 7 inches of clearance between the slide out box and other items on the side of the RV like awning rails or doors. If you have 7 inches of clearance on both sides and the flange width of your slide out is between 80 and 85 inches this would fit and work great. view full answer...
The ClearPlus 78 Series HD Windshield Wipers # CP78321 are slightly smaller than 1/2" wide and fit inside wiper arms between 1/2"-5/8" wide. I would check to make sure that your washer sprayer hoses don't actually attach to the arms instead of the wiper blades, but as long as the clamps that attach the sprayers onto these are not larger than 1/2" wide, you will be able to mount them on the blades. view full answer...
If only one unit isn't keeping up then you can replace just that one unit without having to replace both. You'll just need to determine how the bad unit connects to the system to figure out the best replacement option. It will typically be a 6 or 9-pin connector, but some times Dometic units can be hardwired. If this is the case then you'll need to contact Dometic to determine what the wire functions are to accurately connect a new unit. You'll also need to reach out to the manufacturer... view full answer...
Yes, SumoSprings come in kits per axle so two kits would be needed if you have a tandem axle trailer. To determine the correct kit for your trailer you'll need to know the axle capacity and whether or not your axles are overslung or underslung. If your leaf spring stack sits above your axle then you're overslung, and if your leaf spring stack sits below the axle you're underslung. The axle capacity can be found on the axle tag that should be stuck directly to the tube of the axle. If not... view full answer...
I was able to verify the correct replacement shroud for your Dometic 630035.331 air conditioner, which is the following part number:
- Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners # AT3308046006 view full answer...
The Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK6-RSSA is a confirmed fit for your 2011 Monaco Vesta. Our fit guide does not confirm a fit under that name simply because we have it instead listed under 2011 Roadmaster Monaco because your motorhome is built on the Roadmaster chassis that Monaco and Navistar designed. The steering stabilizer with mounting brackets, does fit on air bag suspension. I've attached a couple photos to assist.... view full answer...
The Valterra Awning Buddy # A30-0300 is a set of two rubberized clamps intended to tighten a sagging awning or to prevent one from flapping in the breeze, but they also sound like they'd be perfect for your similar application to secure a vertical sunscreen to the same awning structure.
I expect that you would need a total of at least 4 clamps (so that means two complete kits) for the top of a 10-foot screen but more may be needed depending on the weight of that screen material. You will... view full answer...
I checked with Roadmaster Inc., manufacturer of the steering stabilizer and not the chassis, and found that for the 2009 Roadmaster Monaco chassis the correct steering stabilizer is # RM-RBK6-RSSA. view full answer...
If you are needing a double step replacement for your 2011 Monaco Monarch Motorhome the Kwikee Electric RV Step Complete Assembly - Double - 32 Series - 24" Wide # LC372261 will be the correct replacement. I was able to confirm this after to speaking to my contact at Lippert.
If you need a triple step replacement the Kwikee Electric RV Step Complete Assembly - Triple - 25 Series - 24" Wide # LC3658373 would the correct replacement. view full answer...
You shouldn't need to replace the entire step assembly of your CoachStep, replacement parts should do the trick for you. As for the current replacement step, since CoachStep was discontinued some time ago, there isn't a specific replacement for these steps, you would need to measure the mounting bracket width and entry height. For example, if you had a mounting bracket width of 25-7/8" available and had an entry height of 23-1/4" - 25-1/4" you could install the Kwikee Electric RV Step Complete... view full answer...
Thanks for that measurement, and the correct awning for a 92 inch flange to flange measurement is one of the following, available in either white or black:
- Black: Solera RV Slide-Out Awning # LCV000168107
- White: Solera RV Slide-Out Awning # LCV000163289 view full answer...
It looks like the 2008 Monaco La Palma XL was built on a Roadmaster Chassis so if this is what you have then you'd need the Roadmaster Exact Center Steering Stabilizer part # RM75RR which comes with both the steering stabilizer as well as the bolt-on mounting brackets. This will be an excellent upgrade for your motorhome allowing the steering wheel to return to center much faster and easier. view full answer...
To determine a replacement for your Dometic Duo-Therm units you'll first need to remove the air distribution box cover and determine the connection type, whether it's a 6 or 9-pin connector or if it's hardwired. Next you'll want to remove the shroud of the rooftop unit to check the BTU rating. There should be a sticker somewhere on it that states either 13,500 or 15,000 BTU's. Depending on these circumstances I have the following recommendations:
13,500 BTU's
6-pin # FR26PR
9-pin # FR82PV
15,000... view full answer...
There is no database or anything that tells us what steps are correct for a motorhome/RV by year/make/model. You would need to know your entry height and mounting bracket width.
From what I could find, your 2008 Monaco Executive Motorhome likely has a 23-3/4" wide mounting bracket. Options like the Kwikee Electric RV Step Complete Assembly # LC372261 (20" - 23" entry height) and Kwikee Electric RV Step Complete Assembly # LC3658373 (28" - 31" entry height) are likely to work if that is... view full answer...
The threads themselves on the Valterra Shower Drain # A01-2012VP are not made from PVC however this drain is compatible with ABS plastic and PVC.
This drain has a 2-1/2" stainless steel flange, and will fit into a 1-3/4" drain hole and 1-1/2" P-traps. view full answer...
Go To Results