Actually, WeatherTech floor mats # WT444191 are listed as a fit for the 2016 Mazda CX-5. For a matching black liner for the back seats use # WT444192. view full answer...
Yes, based on our experiences with very similar vehicles with the Swagman Chinook 2 Bike Platform Rack # S64683 that you referenced your rear door would easily be able to open with the rack tilted down.
I attached a picture that shows the rear hatch of a very similar vehicle opening with the rack tilted down and you can see there's plenty of clearance.
If you need a trailer hitch installed as well the # e98902 provides very similar clearances to the hitch in the picture I attached. I... view full answer...
Fortunately, we do have a review video that shows how we measure the 13-1/4 inch height of the Thule Motion XT Alpine # TH629506. The height is measured from the bottom of the box itself (not from the bottom of the clamps that attach the the crossbars). I went ahead and attached a video that shows this height measurement at time stamp 2:12. With this measurement, you will be under the 16.5 inches that is between the garage opening and the cargo box. With this height, there is no need to... view full answer...
For your 2014 Mazda CX-5 Touring, I recommend the Tow Ready T-One Vehicle Wiring Harness # 118563. This wiring harness is confirmed to work for CX-5s with or without LED taillights and will work well with your vehicle's wiring system. I spoke with my contact at Tow Ready and he confirmed that your CX-5 does not have pulse width modulation.
Since the # 118563 wiring harness has a powered converter, it will use the vehicle battery to power the trailer's lights. Non-powered wiring harnesses,... view full answer...
Yes, I checked with Yakima and the SkinnyWarrior Roof Rack Cargo Basket # Y07014-16 that you referenced does fit the factory crossbars of a 2005 Honda Element. view full answer...
While the design of the Draw-Tite Receivers # 76138(2") and # C12170(1-1/4") may allow their receivers to still fit, it may have changed enough that the Mazda receiver will no longer fit correctly. Since Draw-Tite designs and tests their own receivers not in collaboration with Mazda they will likely have differences.
We also have the Tekonsha T-One Vehicle Wiring Harness # 118746 that is confirmed to fit your CX-5. This will allow you to connect to most small trailers you may pull. It... view full answer...
The most affordable wheel mount bike rack option is Malone Pilot TC ST Roof Bike Rack part # MPG2103. The universal brackets fit round, square, aero, elliptical, and most factory crossbars including the aero bars of your Rola GTX 59767. The Malone's adjustable wheel holders accommodate 20" to 29" Wheels with up to 5" wide fat tires. The aluminum construction of the rack weighs 10 lbs compared to other roof mount bike racks that can weigh up to 20 lbs for vehicle's with lower roof capacities.... view full answer...
The Rola 59723 will not fit your 2015 Mazda CX-5 but we have similar racks that will! If you have factory installed raised rails, you can use the Malone AirFlow2 Roof Rack # MPG216 it is a super simple install and I've included a video for you to check!
If you have a naked roof, you'll need to get the Thule WingBar Evo Crossbars # TH711420 the Evo Clamp Feet # TH710501 and the Fit Kit for Thule Evo Clamp Roof Rack Feet # TH145110. I've included a video to help you with the install! view full answer...
I would be happy to help you select a wiring harness for your 2020 Mazda CX-5. The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # C56377 you were looking at does fit your vehicle but I recommend going with the Tekonsha. The Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118746 connects in line behind your CX-5's rear tail lights and plugs directly into the lighting harness. This will provide you a 4-pole flat connector... view full answer...
We do have roof baskets that fit your 42" crossbar spread, but the Curt basket you mentioned will not, like you mentioned. I checked every roof basket available, and you have two options for a roof basket that will fit a 42" spread:
- Rhino-Rack Roof Mounted Steel Cargo Basket - 57" Long x 42" Wide # RMCB02
- Yakima OffGrid Roof Cargo Basket - Steel - 62" Long x 40" Wide # Y07138-08 view full answer...
You will have no problem fully opening your rear hatch with the GearDeck 17 Enclosed Cargo Carrier # H00604. It slides straight back from the vehicle 50 inches from the hitch pin hole and gives you full access to the cargo area of your 2013 Mazda CX-5.
Please make sure that you have a class III or IV hitch on your Mazda. This carrier cannot be used with a class II.
Take a look at the attached video to see this carrier in action. view full answer...
The Thule Motion XT 22 cubic foot cargo box, part # TH629906 requires 55 inches of front clearance. To determine if it'll fit on your CX-5, you'll need to measure from the center of the front crossbar rearward until you reach the seam where the liftgate meets the roof (if the crossbars are adjustable, make sure it's pushed all the way forward) If this distance is less than 55 inches, the hatch will hit the cargo box before opening completely. The # TH629906 accommodates 5-7 pairs of skis... view full answer...
The Kenda Karrier S-Trail ST145/R12 Radial Tire part # AM10130 will work with either 8" or 10" drum brakes so if this is what you have then you'll be fine. Please note, the drums are measured from the inside. I don't have the exact measurement you are looking for but so long as you have one of the above two sizes which is very likely then you'll be good to go. view full answer...
There are two wiring harnesses for your 2013 Mazda CX-5 and the correct one will actually depend on if your Mazda has LED taillights as opposed to the trailer you are pulling.
So you can use the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56011 on your '13 Mazda CX-5 so long as the vehicle does not have LED taillights.
If your Mazda does have LED taillights you will need the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118563, and... view full answer...
The Tow Ready J-Pin Stabilization Pin and Barrel will fit the Draw-Tite Max-Frame Trailer Hitch Receiver # 76138 for your 2018 Mazda CX-5. The J-Pin fits 2" receivers as long as they have the secondary hole. The Draw-Tite # 76138 has the secondary hole closer to the back of the receiver tube. view full answer...
While we have not yet (October 16, 2023) confirmed the # C13315 to fit the 2024 models, I believe it is safe to assume that it will carry over to 2024, since the # C12170 has been confirmed. Both hitches use the same configuration for the side flanges, and both install in the same location.
I will say that we cannot give a 100% guarantee that it will fit. We would need to get word from Curt, or get our hands on a 2024 model here at our shop in order to confirm fitment. As far as we are... view full answer...
Yes, it will! I checked with Curt and I can confirm that their Item # C12170 hitch does indeed fit the 2024 Mazda CX-5.
The Curt Hitch item # C12170 is a class II hitch with a 1-1/4" receiver. It is custom fit and bolts to the 2024 CX-5 with included hardware. This hitch has a 3,500 lbs towing capacity and a 350 lbs maximum tongue weight.
I have attached a couple of pictures below along with an installation video so you can see what this hitch looks like installed and how to get it set... view full answer...
According to Draw-Tite, their Class I hitch, part # 76138 is a confirmed fit for the 2014 CX-5.
If you'll be using the hitch for towing purposes, you'll also need the following:
Trailer wiring harness with 4-pole trailer connector, part # 118563
Ball mount, part # 2753
1-7/8 inch ball, part # 19260
2 inch ball, part # 63845
Locking hitch pin, part # e98882
I've linked you to an install video for the hitch and the trailer wiring harness. view full answer...
According to Draw-Tite, the Class III # 76138 is indeed compatible with your 2015 Mazda CX-5.
If you'll be using the hitch for towing purposes, you would also need the following items to complete your towing system:
Trailer wiring harness, part # 118563
Ball mount, part # 2753
1-7/8 inch trailer ball, part # 19260 or 2 inch ball, part # 63845
Locking hitch pin, part # e98882 view full answer...