There is no specific torque setting for the axle nut with the # AKIHUB-440-2-G-EZ-1K. Check out the installation video below starting at the 13 minute mark. The hub is overtightened at first to make sure everything is seated. Then he backs off the castle nut until it is loose. After that, tighten it back until you get a little bit of pressure and make sure there is no play. Then you will check your holes for your cotter pin. For the lug nuts you're going to have 8-14" wheels and this has... view full answer...
Hello Jim. The Stealth Hitch # 391SUCT18 is not verified for the 2022 Subaru Crosstrek because the manufacturer specifies it will only for the 2018-2021 Crosstrek models. Unfortunately, Stealth Hitch does not make a hitch for the 2022 - present Subaru Crosstrek.
We actually had a few reps from Stealth Hitch here a couple weeks ago and I brought this up. We get a lot of Subaru owners asking us about stealth hitches and I was curious why they stopped making hitches for a lot of Subaru models... view full answer...
Hi Vijay,
Since you're wanting to go with a wireless brake controller you can use the Curt Trailer Connector Adapter # C57672 you were looking at and just cap off both the yellow and blue wires with some electrical tape. These can be saved for use later on if you want a hardwired brake controller or have a boat trailer with a reverse lock out solenoid. You'll need to pick up some 10awg wire # 10-1-1 to run from the black wire up to the battery and a 40 amp circuit breaker # 9510 inline... view full answer...
Hi Rod,
It is possible you can use the etrailer Hard Tonneau Cover # e95DR with a bed extender, but it depends on how the extender installs. The extender would need to be even and no further than where the tailgate installs, like the Curt Universal Truck Bed Extender with Fold-Down Tailgate # C57WR. view full answer...
The plug cannot be removed from the back of the connector on the # HM11143384. Installing that Diode Dynamics C1R would require some splicing. To avoid splicing on the C1R wiring harness you could cut off the current connector and splice in the Pollak 7-Pole, RV-Style Trailer Connector # PK11898. This would allow you to plug the C1R in-line with the 7-way as intended. view full answer...
Hi Audra,
There are a couple of things to check for a leaking Dometic RV Water Heater # DMC74FR since your connections are sound. The first thing you want to check is the relief valve (if you aren't sure where that is I have added a link below to the instructions which point it out), as that can sometimes drip.
That would be my guess, but the other thing to check is the tank itself could have a small fracture somewhere. That would be very difficult to find but you can try and take a... view full answer...
Hey Dan,
The ground for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles # RM-88400 typically gets tied into the ground for the braking system to intertwine them so that they're active at the same time. When used to prevent turn signals from overriding the brake signal the relay is essentially just a switch that requires the running light signal from the motorhome in order for it to turn on so that it doesn't interfere with the vehicle's signals when not being towed.
We find wiring... view full answer...
We do have a network of dealers that would be able to install the Demco Air Force One # SM99243 in your Jeep Cherokee Trailhawk. I have attached a link below with a list of our top dealers in the area. I used 32501 as the zip code but you can change it to whatever you need. view full answer...
Thank you for providing that picture with the serial number. According to Lippert you have a 15,500 lb Lippert 1621 pin box. The correct Reese Goose Box for your 2019 Keystone Cougar 369BHS is the # RP94716. view full answer...
Thanks for your continued support Michael! I drive out to Kansas a few times a year myself and I definitely know the drive you're talking about.
Your Thule Quest TH846 was actually replaced by the Thule Outbound Rooftop Cargo Bag # TH868 and they install the same way. They have the front and rear straps for crossbars, but Thule also points out that the side anchoring rings can be used if the only anchoring option for your vehicle is the side rails (see attached clip of instructions).
Thule... view full answer...
I attached a link to this page that you can use to find a local installer to you for installing base plates and other flat towing components. view full answer...
We haven't had a chance to install the # C31088 on the 2020 GMC Sierra 1500 or similar models yet so we do not have an installation video at this time. The best I can offer are the written instructions which I attached below. The process isn't too extensive with only 6 steps to complete the installation. Trimming of the air dam is required but Curt includes a diagram in the instructions. view full answer...
Since our etrailer Trailer Hitch Receiver # e25TR mounts to the rear of the frame behind the bumper impact structure on your 2024 Subaru Outback Wilderness it will not require removal/loosening of the heat shields. There is enough room to get to the single bolt hole on each side which sits just above the exhaust hanger without having to remove the exhaust. view full answer...
I do see that Curt has extended the fit for the Curt Trailer Hitch Receiver # C11394 to the current 2024 Mitsubishi Mirage. The only modification required is enlarging the access hole to pass the carriage bolt and square hole spacer into the frame. I have included an installation video near the bottom of the page which shows the hole being enlarged near the 6:30 mark of the video.
I recommend installing the Curt T-Connector Vehicle Wiring Harness # C56223 when you install the receiver.... view full answer...
Thanks for reaching out about the Correct Track Trailer Alignment and Lift Kit # RR23QX, Mike!
The instructions only mention adjusting the front axle before the rear axle, but I agree with you - the middle hanger that holds the equalizer will need to be installed first so that everything else can be lined up correctly. view full answer...
More than likely the # C45CR was slightly bent during shipping. This is usually the reason the holes won't line up during installation. Unless it is severely bent (cracks or chipped paint can indicate it is unsafe) you can bend it back and get your hitch installed. You can use a vise, step, or even some boards to bend it back. I have attached an article below which covers all of these methods for your reference. view full answer...
Hello Chase. To replace the regulator on your Furrion # FGH4ZSASS Cooktop you can use the Replacement Gas Inlet Connector and LP Regulator Inlet Assembly # FR97PR. The regulator is easily accessible from on the front left of the cooktop. Depending on how you have it installed you may have to remove the cooktop from the counter. It really just depends on if you have room to get your tools in there to remove it. Removing the cooktop from the counter will definitely make installation much easier. view full answer...
Since your 2023 Dodge Charger Pursuit has the V6 engine we know it isn't an SRT, Hellcat, or Demon. This means you can use the Curt Trailer Hitch Receiver # C13236. This is a Class III hitch with a 2" receiver, bolt-on installation, and a lifetime warranty. It also has a max tongue weight of 350 lbs which will be more than enough for your bikes and bike rack. view full answer...
For custom fit 5th wheel brackets that fit your 2022 Chevy Silverado 2500 you will need the Curt Custom 5th Wheel Bracket Kit for Chevy/GMC Truck item # C16429. These mount in pre-existing holes in your truck's frame.
The item # C16429 and the Curt Universal Fifth Wheel Base Rails item # C16204 are kitted together as the Curt Custom Fifth Wheel Installation Kit item # C16429-204 if you need the entire set up.
I have linked an installation video below so you can see how to get them set... view full answer...
Hey Kevin.
The Tekonsha Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit # 119147KIT is a universal-style trailer wiring harness that requires splicing into the factory wiring and running a separate wire to the battery for power. It's compatible with PWM and multiplex wiring, but with it being a universal-style kit they don't have model specific directions, just generic ones. the power wire for this harness would need to be ran to the positive post of the battery. view full answer...
Go To Results