I contacted the manufacturer regarding your questions about the Demco SBS Wireless Coachlink for Supplemental Braking Systems # SM99945.
They were able to tell me that if you have the the transmitter wired to the vehicle’s stop switch, yes it will transmit anytime the brake switch is activated. When the transmitter is activated it uses milliamps, no power is taken when the transmitter is NOT activated by the switch. view full answer...
The LED Light Strip Kit, # DG52694 has two 4-pin connectors with to recombine strips once cut. Any extended length of wire needed for a custom installation will need to be sourced separately from the kit itself. I suggest at least an 18 gauge solid core wire at minimum. view full answer...
There is not a preferred location to run the wire for the breakaway switch on your 2020 Jeep Wrangler Unlimited for use with the Blue Ox Patriot Braking System # BLU37TR.
Since you don't have the grommet to pass the cable through, you can drill the 1/2 inch hole in the firewall literally anywhere that gives you the best access. Just make sure to double check before drilling to ensure you don't damage or run into any wiring or other parts. Otherwise, there isn't a specific location on your... view full answer...
In order to install the # TR118821, you will need to do a little splicing but the easiest and safest way to do that would be to tap into the wires on the Curt # C56407, the procedure for this is shown in the instructions for the # TR118821, which I've linked for you. Installing in this manner will not harm the trailer wiring harness in any way.
I've linked to some videos that you might find helpful. view full answer...
That is correct. The Aries ActionTrac Motorized Running Boards - 70" # AA3025165 just come with the boards alone. However, we do have the 70 inch Aries ActionTrac Motorized Running Boards with Custom Installation Kit # AA3036570 that comes with all the installation materials required specifically for your 2012 Jeep Wrangler. view full answer...
To install the P3 brake controller # 90195 in your 2013 Jeep Wrangler Unlimited you are going to need to do a little hardwiring using pig tail # 20127 and installation kit # 5506.
The white wire you will need to connect to the negative battery terminal. Black will go to the positive battery terminal via the circuit breaker included with the installation kit. Red will connect to the cold side of the brake switch.
You will need a circuit tester such as # 3808 to test the wires on the brake... view full answer...
The Bestop PowerBoards, # B7515215, will fit the 2013 Jeep Wrangler Unlimited. But, if your Jeep has the Rubicon rock rails or another style of running boards they will have to be removed in order for the running boards to be installed. view full answer...
The Roadmaster Rear Anti-Sway Bar part # RM-1209-140 as the title states is for the rear of a motorhome, one with a Freightliner XC V-Ride Chassis to be specific. I am not sure where you seen that it is for the front but this is not correct. In regards to what is included, you are correct that there are no polyurethane bushings for this particular model but many others do use them. The above just comes with side brackets and hardware which you can see in the attached photo. view full answer...
I'm sorry to hear about the troubles you are having and I can tell you that on your 2014 Jeep Wrangler JKU with the factory tow package, you are going to need circuit breakers when using a brake controller.
You will need the Wiring Kit for Electric Trailer Brake Controllers # 5506 which comes with wire, circuit breakers and attaching ring terminals and butt connectors to properly install a brake controller such as the Prodigy P3 # 90195. It has a 40 amp breaker for the 12 volt of your... view full answer...
I spoke with my contact at Carr and she told me that the Carr Custom-Fit Super Hoop Side Steps, # CARR101241, will fit on your 2014 Jeep Wrangler with the Rock Rails, but the Rock Rails will have to be removed to install the Super Hoop side steps.
Once you have the Super Hoops installed, the Rock Rails can be re-installed in their original location. view full answer...
Yes, you can use Blue Ox Base Plates # BX1134 with the winch on your 2015 Jeep Wrangler Rubicon Hard Rock Edition. The winch is in the middle of the bumper on this vehicle and the base plates mount to the outside frame so there will be no interference between the two parts. view full answer...
According to Roadmaster, the average installation time for the Roadmaster Direct-Connect Base Plate Kit # RM-521453-5 that fits your 2020 Jeep Wrangler is about three hours. That could depend on the experience though, so if it is a first-time installer that hasn't done it much, it wouldn't be surprising for the install time to go past that into the five hour territory or so. Anything in that time frame would be appropriate for a professional installation.
If you do need other parts in... view full answer...
Beginning with the brake controller installation procedure, you will need to use the pigtail wiring including with the P2 brake controller # 90885 to hard wire the unit to your 2010 Jeep Wrangler Unlimited. You will need to use a light tester like part # PTW2993 to locate the circuits on the vehicle to which the pigtail will be connected. I am including a link to brake controller installation instructions, if needed.
The 4 brake controller wire functions are:
White: Ground, attached... view full answer...
I spoke with my contact at Camco and he informed me that the regulator of the Little Red Campfire Portable Gas Campfire # CAM58031 is adjustable. It allows you to control the flow of the propane so that you can adjust the height of the flame.
Closing the regulator all the way turns off the flame and opening it all the way allows the flame to be as high as possible. view full answer...
While we do not have a video showing how to use the Eye Bolt Kit for Rhino-Rack Pioneer Platform Rack, part # JB0892, with M10 bolts to secure a roof-top tent, I can explain the idea using the demonstration video for that bolt kit. I've linked to it below.
The 1:08 mark shows all of the hardware included with the kit. From there, you see Colin explain how to place those items on the eye bolt (small lock washer, then big flat washer, then smaller flat washer, then slightly threading the... view full answer...
A professional installation can vary. It all depends on how the installer chooses to route the wiring from the back to the front and how they choose to go through the firewall on the vehicle. But it should take 2 to 3 hours to perform the installation.
I have included some links to the right that should also help. view full answer...
Most likely you will not need a brake light relay for your 2015 Jeep Wrangler Unlimited. I recommend wiring the Wrangler first and checking to see if you need a brake light relay before installing it.
You will want to connect the Jeep's wiring to the motor home's, put the Jeep in tow mode, turn on the motor home's blinker, and then have a helper step on the Jeep's brake. If the turn signal continues to blink on the Jeep, you will not need a brake light relay.
We have not installed the... view full answer...
Your 2012 Jeep Wrangler Unlimited does not have the factory brake controller wiring harness. The only way to install a brake controller such as the Tekonsha Prodigy P2 Trailer Brake Controller part # 90885 (Great Choice) would be to hardwire the controller into your vehicles wiring harness. Though certainly not as easy as just plugging a harness in, hardwiring a brake controller is not too difficult of a task. I have attached an installation video of the controller installed on a 2012 Jeep... view full answer...
While we don't have a longer version of the # P960 that will work for you I was able to look at the tire size you have and I can tell it's a 12.5 inch wide size. Which for that we have the Hollywood Racks SR2 2-Bike Carrier # HRSR2 which can fit up to a 12.5 inch wide tire. view full answer...
Yes, there was a design change with the nuts that were originally welded to the Hidden Hitch, part # 75515, to the current Draw-Tite, part # 76104. The nuts are no longer welded to the hitch itself but are still included. The newest version of this hitch it sht # DT78MR.
I've linked an install video of the # 76104 and the # DT78MR for you to check out the newest improvements. view full answer...