I have a solution for you, but the 8100TR model number was in a lot of the older Fan-tastic Create-A-Breeze vents, which have since been discontinued. You can use Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans part # FVK8017-00 you were looking at, which is designed to replace the bow tie bracket, fan blades and motor.
The motor alone is not available but this is a great upgrade to the old motors since many customers have said this replacement is less squeaky compared... view full answer...
Your 2000 Jayco Eagle likely uses either Stromberg Carlson Electric Landing Gear Set # LG-1 or a Lippert setup like Lippert Electric Landing Gear Set # LC333964. You will want to confirm this, but if you need the replacement lead leg for Stromberg setup then go with Lead Leg # LG-179013 which has total lift of 34-7/8" and uses Motor # LG-217884. If you have the Lippert setup then go with Lippert Components 32" Lead 5th Wheel RV Landing Gear Drop Leg # LC179013 and motor # LC142178 if you... view full answer...
The Replacement Door # AT91385 will fit your Atwood RV Water Heater # AT94022 (GC10A-4E) on your 2016 Jayco North Point 5th Wheel camper. view full answer...
Jayco tends to use Dometic A&E awnings so you'd most likely have to purchase an entirely new slide topper since we currently only offer Solera branded components. I haven't gotten to work on Dometic awnings so I can't say if it's the same but Solera awning springs can be reset inside of the roller tube to get the tension back. Yours sounds like it might be a bit more broken than just re-tensioning the spring though so you'd like need to replace the arm(s).
If you have a Solera model then... view full answer...
Based on the 3,500 pound axle on your trailer, the correct replacement grease seal should be the etrailer.com # 58846 that has an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. You can measure your spindle to verify this will fit.
Then for grease caps, if you are looking for Bearing Buddy Bearing Protectors, I recommend # BB1980A-SS. These have a stainless steel construction and will fit 1.980 inch hub bores, which are typically found on 3,500 pound axles.
If... view full answer...
Thank you for including the model number of your fan, 04751KS, which was exactly what was needed to find your replacement circuit board.
The correct part for your MaxxAir MaxxFan Plus Roof Vent 4751KS is:
- Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS
This is the correct replacement circuit board for models 4751KS, 4761KS, and 4951KS. I have added a link to a video review for you to check out as well. view full answer...
The Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs # 8-219-13UC3 will fit on your Lippert axle. They use the same size bearings and seal. view full answer...
For a replacement jack for your 2021 Jayco Jay Flight SLX 7 174 BH I recommend the Stabilizer Jack - 6-1/4" Drop Leg Travel - 18" - 650 lbs # TJ01RT. This jack same mounting hole dimensions as your current jack at 3 inches apart on center. It has a 650 lb capacity per jack and extends up to 18". It is also sold as a set of 2 ,including the handle, which would be the # TJ01RT-HD. These would also be a great addition to the front of your travel trailer.
I have attached a picture showing... view full answer...
The best way to determine the correct replacement pitch arm for a Solera awning would be measuring. The part # LC74VR measures 78", the part # LC67VR measures 63", and the part # LC375994 measures 69". If you have another length please let me know what that is and I will see if we have another replacement for this. view full answer...
The load range D on the Loadstar ST185/80D13 # AM1ST79 actually gives you a higher weight rating than the C load range. For this size D is 1,710 lbs at 65 psi while C is 1,480 lbs at 50 psi. It doesn't hurt to have a tire that is rated for more weight and the benefit to this tire is that it has a max speed rating of 81 mph. If you need a wheel as well then I recommend part # AM3S331 as this is the same tire but it comes with a white wheel that has a 5 on 4-1/2" bolt pattern.
Bias tires,... view full answer...
It appears your 2003 Jayco Qwest uses an A-frame tongue which would require a Demco Hydraulic Brake Actuator # DM8609502 to be welded on in place of your Atwood 85736 master cylinder.
We do have the Demco Hydraulic Brake Actuator # DM72VR which bolts to a 3" wide straight tongue if you do not have an A-frame tongue. view full answer...
The correct replacement transfer switch for your PD52 transfer switch in your 2019 Jayco North Point, is the:
- Progressive Dynamics Transfer Switch - Metal Case # PD52.
This transfer switch can automatically reroute your RV's AC input from shore power to generator power, and can also be use with an inverter in place of a generator.
Attached is a review video for you to check out as well. view full answer...
Thank you for the photo!
For your Ventline Range Hood PH CC0431-09 you're either going to need the motor # BVD0218-00 or the motor # BVD0218-00C. The first motor is for an unlisted range hood while the second motor is for a CSA range hood.
To determine whether you have an unlisted or CSA range hood you'll look for a dark label on the side of the blower housing that will have something to the affect of "Certified to CAN/CSA STD." on it for a CSA listed hood according to my contact at Ventline. view full answer...
We do not have a slam latch (matching or not) that fits in the door cut out of the Global Link lock that you currently have. Depending on the thickness of the compartment door you may be able to install a Global Link # 295-000014 thumb turn cam latch. If you need a different size just email me back with your door thickness. view full answer...
For your 2015 Jayco White Hawk 27RBOK I recommend our etrailer Self-Adjusting Electric Trailer Brake Kit # AKEBRK-35-SA. These self adjusting brake improve braking feel and extend the life of your brakes as they keep all 4 hubs in close adjustment for even braking across all brakes.
For the hubs/drums you will want to verify that your current hubs match. You will likely need the Easy Grease Trailer Hub and Drum Assembly # AKHD-555-35-EZ-K. You need to verify that your current axle has... view full answer...
The closest option we carry to your 17 x 11-1/2" sink is the Better Bath RV Bathroom Sink # LC209354, which is 17" long x 14" wide. If you're able to trim the cutout hole a bit wider then you'll be able to swap of to this sink instead. If not, I would reach out to Lippert directly since they have a much larger selection of sinks and are a top OEM choice so you might also be able to find your exact sink model to replace it with. view full answer...
The leg on your Atwood Power Jack AT80718 is not replaceable and since this jack is now discontinued by the manufacturer, the only solution is to replace it with a new jack.
For a comparable jack, my expert recommendation is the Bulldog Powered-Drive Trailer Jack # BD500188. It features the same 3,500 lb capacity as the AT80718 but offers you a 22 inch lift which is a few more (3) inches than your current jack. It has a retracted bracket height of 9-3/4 inches and will work perfectly on... view full answer...
It appears the part number you have listed may be a Marshal brand, we do not carry this brand but do have high quality components available from MB Sturgis. The length of hose needed, thread size and type are required to ensure a proper fit for replacement. We have the MB Sturgis, # 100473-12, a 12" hose with the needed Type 1 - Male on one end of the pig tail and a 1/4 Inch - Male NPT on the other. See the attached product review video. We also have the same hose but in a 15" length... view full answer...
From what I have found, it looks like the LED Trailer Tail Light - Stop, Turn, Tail - Red Lens Passenger Side # 328-003-81BM1 and Driver Side # 328-003-81LBM1 are the closest in appearance and design when compared to your current tail lights.
The dimensions of these lights are 8-11/16" long x 5-7/8" tall x 2" deep if you would like to compare them to your current lights. They have a 3-wire design and 22 diodes each. The lights mount to the surface of your trailer so you can mount them... view full answer...
There is not a cross reference for campers that allows me to look up what latch set is installed on your pop-up camper. However, you can view the linked video below that shows how to remove/replace a door latch. It is actually very simple and only requires a screwdriver. Doing so will let you measure the cut out of your door. The Global Link RV Entry Door Locking Latch Kit with Keyed Alike Option, # 295-000019 installs into latch cutouts that are 2-1/2" wide x 3-1/2" tall to 3" wide... view full answer...
Go To Results