For a three-camera setup for your 2019 Jayflight that was prepped for Furrion Vision S observation systems I have a really great option for you. Take a look at the attached video of the 5-inch monitor setup part # FCE48TASL-05. view full answer...
The Phoenix Electric Trailer Jack with Remote # UF38-944055 will have plenty of lifting capacity for your 6,050 lb. trailer and has the most amount of lift at 26". Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. So this jack will be able to lift your trailer and provide you with a significant amount of lift to help with hooking up to your lifted truck. view full answer...
In regards to trailer shackle links, they should be at a 45 degree when loaded. If you recently upgraded to the Equa-Flex Cushioned Equalizers part # LC279687 and the shackle links are no longer at a 45 degree angle. This is likely because the new equalizers are not the same size as the old. If there isn't another size you can use to correct this then you can make up whatever difference there was with shorter/longer shackle straps, I have attached our selection below.
If you can let me... view full answer...
I don't know what unit you have on your 2015 Jayco JayFlight 26BHS but if it happens to be a Dometic the Advent Air Unit part # ACDOM150 that you referenced was designed to easily replace Dometics so it would be a really great solution. It uses wiring connectors that would plug right in and allow you to use your current thermostat.
Otherwise the part # ACM150C is a really great option that comes with a start capacitor and an air distribution box. view full answer...
The Roadmaster Comfort Ride system part # RM-2460-2560 is a much more complete and better performing kit than just shock kits. The shock kits are sometimes challenging to install since they don't always like to easily fit all applications well whereas the Comfort Ride comes with replacements for all components so everything installs easily and also works really well together since it was designed to be used together.
The feedback and reviews for the Comfort Ride is also consistently higher... view full answer...
You can definitely replace your current brakes with a disk brake set up. However, there are a few things that will need to be checked and upgraded to accomplish this task.
First, you will need to determine which inner and outer bearings fit your spindle. As an example, the Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs # K2HR35D is designed to fit spindles with an # L68149 inner bearing and # L44649 outer bearing on a 3,500 pound axle. This will also use a 5... view full answer...
The l-shaped brackets you are referring to on a Fastway e2 Weight Distribution System like part # FA94-00-0600 should not move back and forth. If they do move back and forth then you will need to make sure they are torqued correctly (75 ft. lbs.) and that they are the correct distance back from the coupler (no more than 30"). view full answer...
I hope it's what you are looking for but I attached a link to an install video for the 12V RV LED Puck Light # 328-K-1003WS that you referenced which does have a push button switch to turn it off and on. view full answer...
Since your axle diameter is 3 inch that would mean that your axle capacity is between 5.2k and 7k so for a replacement spindle the EZ Lube Spindle part # TRU37FR would fit and work well. This has a 5 bolt spindle though. view full answer...
I recommend the Bauer Products Camper Door Lock - Black # BA54FR. I feel they are a good quality brand and easy to operate. You can get them keyed alike by using the drop down menu before you add them to your cart.
This particular version requires a cut out of 2-3/4" wide and 3-3/4" tall. It fits doors that are 1-1/4" to 1-1/2" thick.
To replace the cylinder locks I suggest the Replacement Cam Lock for RVs - Chrome Finish - 7/8" Long # BA56FR. They are an easy and straight forward install.... view full answer...
The LED Light Strip Kit with Wireless RF Remote - Weatherproof # DG52688BU that you referenced can only be plugged in and powered from one end of it as there isn't a T fitting you could install on it. view full answer...
For a replacement entry door latch we have the Global LInk RV Entry Door Latch # 295-000019 which is a universal design for RVs like what you have. We do not have replacement springs though for what you have. view full answer...
There's a wiring diagram in the install instructions for the Dometic RV Water Heater part # DMC74FR that I attached to this page. I don't have a way to verify what the wires of your RV are that ran to your old water heater though. We do have to recommend that a qualified tech be who installs the water heater. view full answer...
To pick out bearings/seal for a trailer hub you will need to remove one of the hubs so that you can remove the bearings and get the numbers off of them.
Or, you can measure the spindle where the bearings/seal ride so that we can pick you out the correct bearings that would fit the spindle.
We can ship to Canada. view full answer...
Yes. The Electric Jack w/ Footplate - A-Frame - 25-1/8" Lift - 3.5K - Black # EJ-3520-BBX can be installed with any of the bolt holes facing forward which will put the head of the jack to the right or left as the bolt pattern is the same no matter which direction it is installed.
This is a popular thing to gain a little extra clearance to open your tailgate.
I included a video of the # EJ-3520-BBX for you to take a look at. view full answer...
Yep!
The Dexter # 84656UC3-EZ will be an exact replacement for the J026K5829 you mentioned. These are both 10" drums with the 6 on 5-1/2" bolt pattern, 3,500lb bearing combination, and easy lube grease cap for your easy lube spindle.
You'll also need to pick up some grease, of which I recommend the # L11380. This high-temp grease is hands-down my favorite for a camper like yours due to how well it holds up to high-heat that the bearings will experience when going down the high way, where... view full answer...
For your 2017 Jayco JayFlight 26 BH, I can only find limited information on tire size. From what I found, it looks like you may have 13 inch wheels with a 5 on 4-1/2 inch bolt pattern. If this is the case, I recommend the Provider ST175/80R13 Radial Trailer Tire w/ 13" White Wheel - 5 on 4-1/2 - Load Range C Item # TA43RR. These tires are rated for speeds up to 81 mph and loads up to 1,360 lbs at 50 psi.
If your tire size is different, please let me know and I'll give you a recommendation. view full answer...
I may have an option for you, however all of our bumper-mount RV hitch receivers are designed to fit larger bumpers than what you have on your camper. Your best bet may be to install a frame-mount hitch like the Curt Adjustable Width Trailer Hitch Receiver # 13703 instead. This trailer hitch is designed for use on trailers or RVs and will be either bolted or welded to the trailer's frame. It will fit box, C-channel, or I-beam frames that are 22 inches to 72 inches wide and provide you with... view full answer...
I don't have any information as to what leaf springs are on any one particular trailer such as a 2007 Jayco Jay Flight 29BHS but if they are double eye leaf springs which are the most common then we should have a Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers that will work. In order to choose the correct one you just need to make note of the equalizer dimensions; part # K71-449-00 for 7-3/4" long, part # K71-448-00 for 6" long, or part # K71-359-00 for 5-3/4" long. view full answer...
Your trailer tire size of 205/75-14 has a diameter of 26-1/8 inches so for a set of wheel and tire covers that will fit and work well we have the Adco Ultra Tyre Gard part # 290-3953 which I recommend for you. These install really easily, provide excellent protection and are made from higher quality materials with better stitching so they will last a very long time as well. view full answer...
Go To Results