The B and W Companion hitch slider base # BWRVB3405 sits a total of 15 inches in front of the center of the gooseneck ball hole you have in the bed of your truck. You'd need to measure 15 inches forward of your ball hole now and you'd know where the rail kit would set and if it would interfere with the fuel tank. view full answer...
From what I could find, it does look like all trim levels on the 2019 Honda CR-V are limited to 1,500 pounds towing. This can be verified by checking the driver side door jamb. There is a sticker with all capacities the vehicle is rated to. The Draw-Tite # 76128 is technically rated up to 4,500 pounds, but you are limited to the highest capacity of the lowest rated component, which in this case will be the vehicle. view full answer...
The trailer hitch (Curt, Draw-Tite, B&W) for a 1996 Ford F-250/F-350 that fits closest to the bottom of the bumper is the B&W Heavy-Duty Trailer Hitch Receiver part # BWHDRH25122 which measures 5" from the top of the flange to the top of the receiver tube. The Curt part # C15300 measures 5-1/2" and the Draw-Tite part # DT45502 5-1/4". view full answer...
The arm length of 68 inches to 81 inches is the range that the Solera Classic Universal Awning Support Arms will replace. So if you have a spring-loaded manual awning with arms that are between 68 inches and 81 inches long, you can use these support arms as replacements. They come in either black or white.
- Black: Solera Classic Universal Awning Support Arms for RVs - 68" to 81" Arms # LC434717
- White: Solera Classic Universal Awning Support Arms for RVs - 68" to 81" Arms # LC434718 view full answer...
The Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2" Ball - Bolt On - 10K # DM14793-95 has a channel portion that is 3 by 3 inches on the inside and then connects to the 50 degree angle A-frame. I've attached a video to assist with other fit questions. view full answer...
The Swagman Trailhead 4 Bike # S63380 arms are 26". The cradle spacing for the Trailhead bike racks is 1-1/4". The 3 bike version # S63365 arms are 24-3/4" long. view full answer...
In regards to a roof rack, you will be always be limited by the lowest rated component which in this case is the mounting feet and they are rated at 165lbs. The Thule WingBar Evo Crossbar System part # TH711220, part # TH460R, and part # THKIT4076 which is a fit for a 2019 Kia Niro is still an excellent option though and as there is not one available with a 220 lbs weight capacity is what I recommend. view full answer...
You have it absolutely right. The 6-1/2 foot width of the Thule HideAway Awning # TH490018 means where it will attach; the 8-1/2 foot length is how long it extends out away from the vehicle.
I have added a link to the installation instructions of this awning for you to check out as well. view full answer...
From where the Stallion Stabilizer Jacks # 288-01892-2 mount to the trailer to the bottom of the mounting bracket measures 3-3/8" but to the lowest point on the leg is 4-3/8" as you can see in the attached demonstration photo. view full answer...
The Trailair Air Ride 5th Wheel Pin Box part # LC158778 is 12" wide at the outside of each wing. I have attached a video for you that shows this measurement at around the 3:10 mark. This pin box is designed to be an exact replacement for the Lippert 1621 and Lippert 1621HD. view full answer...
The Malone TopTier Load Bar Kit for Utility Trailers part # MPG493 measures 54" tall from the bottom of the upright to the top of the crossbar. The uprights will fit on the floor of the trailer so if you measure from the floor up 54", that will then give you the height of the crossbar. That said, if needed you can trim the uprights to decrease its overall height. view full answer...
The only equalizer we have available that measures 6-1/4" center to center is part # TREQ458 which a curved equalizer that is 2" tall. If your equalizer is taller you can use Curved Equalizer for 1-3/4" Wide Double-Eye Springs - 6-1/8" Long - 9/16" Center Hole part # TREQ356 that measures 6-1/8" bolt hole to bolt hole and 2-1/2" tall.
I recommend CE Smith Shackle Strap - Galvanized Steel - 2-3/4" Hole-to-Hole Length part # CE14103G.
To get you the correct replacement axle, I would need... view full answer...
The Adco Tyvek All-Climate + Wind RV Cover # 290-34877 that you referenced has a total weight of just about 40 pounds. This particular cover is designed for trailers that are between 37 and 40 feet long. view full answer...
The cutout dimensions for the Furrion RV Refrigerator # FCR14ACBQASS are 72-11/16 inches tall, 31-3/4 inches wide, and 22-13/16 inches deep. I have attached a diagram from the install manual that you can use for reference as well. view full answer...
The AirBedz XUV Air Mattress # 341030 that you referenced in your question has overall dimensions of 66 long x 52 wide (at the widest point) x 10 deep.
Another air mattress that fits your 2013 Honda CR-V is the Pittman Outdoors Rear Seat Air Mattress # 341033 which is smaller and which is intended for use in the second row seat. This mattress has dimensions of 55 long x 35-1/2 wide x 17-3/4 tall. These and other mattress items for your 2013 CR-V appear on the linked page.
All of these... view full answer...
The Thule Hullavator Kayak Carriers # TH898 weigh 40-lbs each by themselves so the two empty carriers alone will consume half of the Pilot's rated 165-lb roof capacity. While there are some lightweight kayaks out there most weigh 40-lbs or more apiece.
Apart from the weight concern there is the matter of space; each Hullavator requires 28.5-inches of space on the crossbars so the Pilot would have to be fitted with at least 57 inch long bars. The Hullavator also requires 4-8 inches of crossbar... view full answer...
The tire you referenced, Kenda Loadstar K364 Trailer Tire 6.90/6.00-9 in Load Range C, item # AM10040, has a weight capacity of 1,298-lbs at 60-psi for EACH tire. It is likely that the special purpose industrial tire you mentioned has that slightly higher rating of 1630-lbs for each tire but if you wish to send me a link to the specific item you're referring to I can check for you.
Since tire makers do not know the specific application - how many axles/tires in total are on a given vehicle... view full answer...