We offer D-ring tie downs like the bolt-on Brophy # SR15-C and the weld-on Curt # J-705 that can be seen on the linked page. For one close to your measurements you might consider the Brophy # LRB1 which is also a bolt-on part whose dimensions are shown in the linked photo. view full answer...
The kit you identified is for a Jeep. I suggest the Hopkins Custom Tail Light Wiring Kit for Towed Vehicles, # HM56101 for your 2012 GMC Sierra. Please note the linked installation video. view full answer...
Yes, we have the B&W Tow & Stow 2-Ball Mount # BW29FR that is capable of a 4-1/2" drop. This fits your 2" receiver like the B&W Tow & Stow 2-Ball Mount # BW44FR you found and will allow you to use it with your MultiPro tailgate. It will also work with the MultiFlex tailgates on Chevrolet trucks.
I do recommend swapping out the pins for the InfiniteRule Locking Pins # 34061775-D. This will ensure that your hitch is secure and the stainless steel locks will not corrode. view full answer...
We offer several trailer hitch receivers for the 1998 GMC Sonoma. The correct one for your Sonoma will depend on the particular version and type of bumper installed. The four possibilities are: Factory Step Bumper, ZR2, Sportside with Non-Towing Bumper and Factory Roll Pan Bumper.
The link at right will take you to our main page for all hitches for the 1998 Sonoma; at the top of the page there is a drop-down menu where you can select the version you have to see the hitches that are suitable.... view full answer...
Yes, we do offer a stand-alone slider assembly that will work with your Pro Series 20K hitch. The part number you need is # RP30092 and its written instructions are linked for you at right, along with an installation video.
This slider is a great way to improve low-speed turning clearance for short bed trucks like your 2003 GMC Sierra. It provides 10-inches of front-to-back travel and will fit any industry-standard base rails from Reese, Pro Series, Curt, Valley, Draw-Tite and Hidden-Hitch. view full answer...
I checked with Torklift and they recommend the # TL44FR for the front tie downs for your truck and then for the rear part # TLC3221. I confirmed these fit the version of the 2020 GMC Sierra 3500 that you have which has a long bed, single rear wheel setup, running boards and factory hitch.
For turnbuckles then we have the stainless Derringer # TLS9020 from Torklift as well. view full answer...
Yes, you can use Demco 5th wheel installation kit # DM8553014-12 in your 2017 GMC Sierra 1500 with 6-1/2-foot bed to install their 16K sliding hitch # DM6076SL-16K. For an in-bed wiring harness you can use part # DM8555002 which is a plug-in item that requires no splicing. Instructions for the hitch and install kit are linked for reference along with a video. view full answer...
If you're speaking of the Reese Elite puck system like what's illustrated in the provided photo, we have exactly what you're looking for. You'll need the Reese Elite Series Underbed Rail Adapter # RP30156 which installs into the existing pucks and provides industry standard fifth wheel bed rails that are compatible with bed rails from Reese, Draw-Tite, Curt, B&W, Valley, Husky and others.
I've linked you to a video showing how the adapter works. view full answer...
We have exactly what you are looking for!
If your 2018 GMC Sierra 1500 is a Z71 then you want the Curt # C31069 but if it isn't you will use the Curt # C31012 instead. Both of these options mount in such a way that just the 2" receiver is showing under the front of your pickup.
I have attached the written instructions for you to reference.
You may also be interested in the Skid Shield # C31007 for when you aren't utilizing the front receiver. view full answer...
I may have a solution for you, but there is not an electric extendable towing mirror for the 2021 GMC Savana. The best available option is the K-Source Custom Towing Mirrors - Manual - Textured Black - Pair # KS62169-70G, which are a manually extending custom fit towing mirror for the 2021 GMC Savana.
I've linked a review video of these parts for you to check out, if you haven't already. view full answer...
I have an alternate option for you but it looks like the ggg111bl1 number you provided comes back to a Ranch Hand grille guard. We do not carry the Ranch Hand line of grille guards, therefore we would not have the brackets that you would need.
The reason for this is because the mounting hardware for grille guards is specific to both your 2014 GMC Sierra 1500 and the grille guard itself. It looks like the ggg111bl1 fits the 2500 and 3500 Sierras which is why the brackets will not work for... view full answer...
For a B&W Companion hitch I recommend using a 10 inch diameter lube plate. We have the Reese Lube Plate, # RP83002, which is my top choice, and the Curt 10 inch Fifth Wheel Trailer Hitch Lube Plate, # 16721, both of which will work nicely with your Companion hitch.
B and W recommends the use of a lube plate so we also recommend it. view full answer...
Yes, the CIPA Custom Towing Mirrors # CM10950 that you referenced have been confirmed as a fit for your 2016 GMC Sierra 2500 and would be an excellent choice for providing you with a better viewing angle as you are towing your 33 foot camper.
We have had reviews from customers who used these mirrors on similar length campers and they said the mirrors did an excellent job and were easy to install so we would recommend them for you.
I attached an install video for you to check out as well. view full answer...
The controller will need to have a trailer connected for it to work. Your best option would be to find a buddy with a trailer who has working brakes and connect to it and see if the brakes work. Or you can put a volt meter on the brake output circuit (5:00 pin) and the ground pin (7:00) and the controller should at that point think that a trailer is connected. view full answer...
I am sorry the Chromed aluminum Sure-Grip running boards you are referring to have been discontinued by the manufacturer. We do have the brushed aluminum Sure-Grip running boards # 27-6120-1835 view full answer...
The # AKIHUB-440-2-G-1K hubs you referenced are compatible with 8,10,12, 13 and 14 inch wheels. We do offer some 12 x 4 and 13 x 5 aluminum wheels with a 4 on 4 bolt pattern.
• Aluminum Split Spoke Trailer Wheel - 13" x 5" # AM22322HWT
• Aluminum Split Spoke Trailer Wheel - 12" x 4" # AM22318HWT
• Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel - 13" x 5" # AM20270
• Aluminum HWT Series S5 Trailer Wheel - 13" x 5" # AM22322HWTB view full answer...
We don't sell the 3/4 x 5-1/2 inch grade 5 bolts needed to lock out a Sidewinder. The only way you will be able to get the correct bolts would be to go to your local hardware store and get them there.
This will save you time as you won't have to wait for the bolts to get shipped as they will be readily available at your local hardware store.
Take a look at the instructions I have linked on page 6 for more on the lock out feature. view full answer...
From our understanding all of the 2007 GMC Envoys came with a factory hitch. Aftermarket hitch manufacturers actually don't sell a hitch for your vehicle because of that. You may have to contact a GMC dealer to track down a factory hitch as I don't see any other options.
You should also have a factory trailer wiring setup as well. But if the socket is missing you could get the # HM40975 that will plug into the factory harness. view full answer...
You bet we do! The Draw-Tite # 65078 and the Curt # C31023 front mount receivers are a fit for your 2015 Sierra 2500. The Draw-Tite model isn't a fit for Denali models, and might require you trim the fascia in order for the receiver tube to pass through. If you live in a state where a front plate is required, you'll need a # 5443 front plate relocation bracket. The Curt model will install with the receiver tube exiting lower on the front fascia, below the license plate, so less cutting... view full answer...
We do offer one set of base plates from Blue Ox that fit the non-Denali 2007 GMC Envoy, part # BX1709. While we do offer adapters to mate different brands of tow bars and base plates, the adapter required for your tow bar is rated only to 5000-lbs and your Envoy's gross weight is roughly 6400-lbs according to my research.
Your solution will be to use a new Blue Ox tow bar that is directly compatible with these base plates. The most popular Blue Ox tow bar that is compatible with this base... view full answer...
Go To Results