The Valterra RV Waste Valve, part # T1001B has an inside diameter of 1.9 inches and the outside of the port measures 2.37 inches.
I went to our warehouse and measured the waste valve for you. I have attached a photo of the valve with the dimensions noted. view full answer...
The width of the smaller opening on the Valterra Double Rotating Waste Valve # T81 that you referenced is 1-1/2 inches and the width of the larger opening on the other side is 3 inches.
These sizes are the standard sizes found on RV valves so most likely the sizes would match up. view full answer...
The end of the Valterra Waste Valve for RV Black Water Tank # T50B that has the lugs has a 3" diameter but the other side with the threads is actually designed to fit over a 3" diameter threaded sewage pipe which is why it measures 3-1/4". As long as you have standard pipe sizes on your RV and the outlet as a threaded end this waste valve will work for you! view full answer...
I took the outermost dimensions of the RV waste valve # T85. It's about 12 inches long, 4-1/2 inches wide, and 9-1/2 inches tall with the handle down or 13 inches with it up. view full answer...
The Double RV Waste Valves - Elbow - Rotating - 3" Spigot and 1.5" Hub to 3" Lug # T80A is 10-1/2" in length from the 3" spigot to the 1-1/2" hub. view full answer...
I went out to our warehouse to take a look at the Valterra RV Waste Valve # T11 referenced in your question. I measured a length of right at 7-1/2 inches from the end of the 3 inch lug to the end of the 3 inch hub. I have attached an image with this dimension labeled that you can also take a look at.
This RV sanitation tee will combine the rotating black-water waste valve and gray-water line. The 3 inch hub slides over the black-water line while the 1-1/2 inch hub slides over the gray-water... view full answer...
The LaSalle Bristol Cable-Actuated RV Waste Valve is offered in a few different length, with 96" part # 34466N4BB96GM being the longest. view full answer...
The length of the wire harness on the valve of the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank # E1003VP is 1 foot. view full answer...
As you can see from the accompanying photo the Double RV Waste Valves # T18 the distance from where the valve hooks up to the black water tank to where you hook up the sewer drain hose is 7-1/2". view full answer...
I attached a picture I got from Valterra that shows the overall dimensions of the Double RV Waste Valves # T68 for you to check out. view full answer...
The overall height (excluding cable) of the LaSalle Bristol Cable-Actuated RV Waste Valve part # 34466N4BB96GM is 14" and the overall width/thickness (spigot to spigot) is 5". I have attached a photo below as well. view full answer...
I went out to the warehouse and measured the dimensions of the Double RV Waste Valves # T84 that you referenced.
Width - 4-1/2"
Length - 12"
Height to Closed Handle - 9-1/4"
Height to Open Handle - 12-3/4"
I have attached a photo to help illustrate those measurements. view full answer...
The distance between the 3" entry and the 1.5" entry on the Bristol Double RV Waste Valves # 34466ND13AAR is 10-1/2". I've attached a picture for you showing some additional measurements as well. view full answer...
The depth of the Valterra Waste Valve for RV Black Water Tank part # T50A measures 4-1/4" end to end without the cap but please note the fittings don't butt up to the end on either side. view full answer...
It is likely the correct fix yes, and the replacement cable actuated waste valve you need is the LaSalle Bristol Cable-Actuated RV Waste Valve for Black Water Tank - Spigot to Hub - 36" Cable # 34466N4AB36GM, 48" Cable # 34466N4AB48GMA, or 72" Cable # 34466N4AB72GMA.
To install it use LaSalle Bristol ABS Solvent Cement # 3447530889. view full answer...
You actually don't need a spacer to attach the Double RV Waste Valves # T80A to your current black water tank. Since you are measuring 3-1/2" for your outlet you have a hub. The 3" spigot end on this double waste valve has an outer diameter of 3-1/2" so it will fit perfectly in the hub of your current setup. In regards to the 3" measurement, that is actually the inner diameter of the pipe itself. If you measure past the hub fitting on your line you should see that it measures 3". view full answer...
Just the valve body thickness of the Bristol RV Waste Valve part # 34466N11AB that you referenced is 1/2 inch. This is a standard width for valve bodies just as the bolt pattern which is right at 2-1/2 inches square. view full answer...