Your Rockwood Signature Ultra-Light with Reese Revolution Kingpin is compatible with the air ride replacement 5th Airborne Premium 5th Wheel Air Ride King Pin w/ Sidewinder and Turret - 16,000 lbs # RP61422. This will give you the same turning function but will help with the shock absorption you are seeking for a smoother ride.
If you prefer a fixed king pin, you can instead use the Trailair Flex Air 5th Wheel Pin Box - Lippert 1621 - 18,000 lbs # LC328492 which won't provide the additional... view full answer...
I recommend using a hitch and hitch-mounted bike rack on your 2018 Honda Fit for a couple reasons. The first is convenience; it is going to be much easier for you to mount your bikes on a hitch-mounted rack as opposed to a roof rack where you'd have to lift the bike on top of your car as opposed to simply placing it in the hitch rack. The other reason is cost; a roof rack will be far pricier than a hitch, and you can either pocket those savings or use it to get a premium bike rack.
As... view full answer...
The Curt Q24 # C16545-16017 is compatible with the newer Ford OEM puck packages. Since the (discontinued) Under-Bed Rail and Installation Kit RP30073 that fits your 2009 Ford F-250 has the pucks in the same location, the Curt hitch is compatible with this under-bed kit.
Please note that the under-bed kit is rated for 18,000 lbs. Even though the Q24 is rated for 24,000 lbs you are limited to your lowest rated component. It is best to always check your owner's manual to ensure you don't... view full answer...
For reflectors to use with the etrailer cargo carrier you have now # e98874 we normally recommend the # RE10RB which is a quantity of 2. These have an adhesive backing that you can use to apply them to the railings of the carrier. This would be the easiest solution but these also have holes you could use to drill into the carrier and permanently like that as well.
Where you want to install them is up to you though. view full answer...
We do have hitches available for your 2021 Toyota Corolla LE. I recommend the Curt Trailer Hitch Receiver # C34UR. This Class I hitch has a 1-1/4" receiver with a gross towing weight of 2,000 lbs and tongue weight of 200 lbs. Make sure to consult your owner's manual to see what your towing capacity is before you do any towing. You will be limited by whatever capacity is lower, the vehicle or the hitch.
Since you plan on towing a trailer, I also recommend the Tekonsha T-One Vehicle Wiring... view full answer...
For a bike rack we have a handful of options but what you're going to be wanting is a platform rack that is classified as a wheel mount. This means that it will have the weight capacity needed for your 40 lb E-Bike and then an arm that secures your bike by the wheel and not the frame.
If you only plane on carrying your 1 bike then I recommend using the RockyMounts HighNoon FC Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount # RKY87RR because it is just smaller and easier... view full answer...
You wouldn't be able to use a RockerBall like # C40047 with a shock absorbing ball mount.
Per the manufacturer, Curt, the RockerBall is not actually able to be used with any type of cushioned ball mount; for the RockerBall # C40047 you would need a standard fixed ball mount with a 1" ball hole diameter for the shank to fit. I have added a link below to our entire selection for you of those ball mounts. view full answer...
For your 2022 Kia Telluride I recommend the Curt Trailer Hitch Receiver # C13420. This is a Class III hitch with a 2" receiver. It has a maximum gross trailer weight of 5,000 lbs and tongue weight of 750 lbs which will be great for your bike rack and towing your trailer. It also has a concealed cross tube to help maintain the factory look.
Since you will be towing your trailer, I also recommend the Curt # CU94FR. This wiring harness plugs into existing wiring and will give you a 4-way... view full answer...
The difference between the Furrion Vision S # FR98NR and FCE48TASL-07 is simply the rear camera design. Typically these camera systems are wired to the running lights so the # FR98NR is best if you're replacing a rear clearance light but would still light to have one there. The FCE48TASL-07 would be best if you're placing the camera in the same area as the light (typically above or below the light) and plan on jut splicing into its wiring.
I've attached some videos below to help with... view full answer...
The Furrion LIT Portable Speaker # FBS012NVPPS is designed to charge off a micro-usb Cable # 332-HDEZ4 when charged inside your home. You will be able to use this type of cable with a cell phone style charger when in your house. If you prefer the Dock # FBS012NCU like you have in your trailer, you can use a small Coverter # FV1101-09 to get the 12 volt power the dock requires. view full answer...
The top rubber strips on the Thule WingBar Evo Crossbars like the 53" # TH711400 you were looking at are a bit different in design compared to the older AeroBar models. Out of the box you'll have a strip of rubber that likely needs to be cut (simply matching its length to the crossbar's).
Once you have the needed length, you will actually pull apart the strip down the middle, separating them into two narrower strips. Then it's simply a matter of pressing them down into the crossbar channel,... view full answer...
Yes! Typically you're looking for a weight distribution system where your tongue weight falls towards the lower end of the tongue weight range of your chosen weight distribution hitch. Because the Equal-i-zer # EQ37140ET has a range of 1,000 to 1,400-lbs, your 1030-lbs tongue weight is in that Goldilocks area that you're looking for, so it will be a great choice for your trailer.
This weight distribution system comes with all of the hardware and parts you'll need to get it installed and... view full answer...
Try improving the connection of the main ground wire of the trailer wiring harness. Make sure it is attached to a clean metal surface. Or you can run all of the trailer wires back to the main ground. This is actually the ideal solution. But you can also check the current grounds for the lights to make sure they are making a solid connection to a clean metal surface.
What you described is the classic insufficient ground scenario so finding a way to improve the grounds will fix the problem.... view full answer...
No, they do not but I have a comparable set that will. They are the Titan Chain Alloy Snow Chains w/ Cams for Wide Base Tires item # TC3231SCAM. These have square links that give excellent traction in the snow plus great grip on ice. The built in cam tighteners let you quickly adjust the fit for simple installation.
You will want to check your owner's manual to see if your vehicle requires Class S compatible chains. If so you'll need the Konig Snow Tire Chains item # KON24FR. They are... view full answer...
Unfortunately Aries only has 3" bull bars as a confirmed fit for your 2024 GMC Sierra 1500 at this time. You will need a new bull bar such as the Aries Bull Bar with Removable Skid Plate - 3" Tubing - Semi Gloss Black # AA88PB, which also comes in Stainless Steel # AA27VB. view full answer...
If you'd prefer something that would be easier to move around the Ultra Fab part # UF48-979033 weighs about half of the K2 you mentioned which was discontinued but would be a little harder to load and unload due to it's shorter ramp. I have a carrier like this and I really like it so it would work great for you. view full answer...
I recommend using the Roadmaster Comfort Ride Shock Absorbers # RM-2450 and the MORryde AllTrek 4000 Equalizers # MR29DR on your 2017 Grand Design Imagine 2600RB travel trailer. These will fit your 3,500lb axles and replace your stock equalizer. You will also want to upgrade your shackles to the MORryde Suspension Upgrade Kit # MR76ZR.
I recommend using the Grease # L11390 and a Grease Gun # L30416 for the wet bolts. This grease is more resistant to water than other types of grease and... view full answer...
There are quite a few A-frame style couplers out there so without more info I really couldn't confidently say if the repair kit part # T4045400 would work for you or not. If you see Dexter or UFP on the coupler and it's a multi fit style coupler with the knob like what this repair kit has it's probably correct though.
The most straightforward solution would be a new coupler like the part # CA-5210-B to replace what you have now though as that would eliminate any guesswork and would give... view full answer...
Since the Dometic FA1250 has a round lid and not a flat lid the correct replacement is the part # FVK1020-19 which it looks like you already ordered so you are good. view full answer...
Yes, we do! It is the Equal-i-zer Weight Distribution System item # EQ37040ET. This system works with trailers that weigh up to 4,000 lbs and have a 400 lbs tongue weight. It has built in 4 point sway control that will keep your trailer in line with your Maverick when you're driving down the highway and make a sudden move or get passed by a semi. This system includes a 2" shank and a 2" hitch ball. view full answer...
Go To Results