The length I'm seeing for your 2019 Forest River Flagstaff E-Pro E19FD is 20' so you'll likely be around 17' in body length and would need the ADCO # AD37ZR since it fits 15' - 18' lengths. If you measure the body and are at or above 18' then you'll want to size up to the # AD97ZR, which fits 18' - 20' lengths. view full answer...
Adding the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # DT78MR is a great option for a hitch on your 2020 Jeep Wrangler Unlimited. It is going to have the highest weigh capacity. The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 6,000 lbs GTW, 600 lbs TW Item # EQ37060ET is going to work great with the draw-tite hitch. The 600lb/6000lb weight capacities on the weight distribution are going to be the maximum weight. With the draw-tite... view full answer...
Looks like your 2018 Flagstaff 19FBS came with the tire size of 205/75-14 so with the lift you installed which will give you more fender clearance the Karrier ST225/75R15 Radial Trailer Tire with 15" Galvanized Wheel # AM32468 that you referenced would fit and work great. You'd have plenty of clearance for it. view full answer...
It sounds like the circuit board is faulty and for replacement we have the Replacement Printed Circuit Board part # MA10-04301k-v16 which should allow you to get your MaxxAir Vent Fan Model 4401K back up and running on the lowest speed setting. If you wanted to replace the motor as well while you were working on it we have this also, the Replacement 12-Volt Variable Speed Fan Motor part # MA10-20968. view full answer...
Can you get me the capacity of the axles you have? It should be listed on the axle or the plate up near the coupler. With that I can pick you out the correct lift kit if available. view full answer...
If your 2011 Yukon XL already has the tow package you're well equipped to tow a Forest River E-Pro 19FD with a 600-lbs tongue weight. It sounds like you might be in need of a weight distribution system to help keep the rear end from sagging too much and creating poor handling conditions that could end up being dangerous. You'll want to choose your weight distribution hitch based off the trailer's tongue weight and you'll want the tongue weight to fall somewhere towards the middle of the... view full answer...
I may have a solution for you to cover the 3,200-Watt Portable RV Inverter Generator - 2,900 Running Watts - Gas - Remote Start # 333-0003, but there is not a cover specifically designed for this model. However, you can use the Storage Cover for etrailer 4,500-Watt Generator - Weather Resistant # 333-0008 and it will do a fine job- it's just a little bit larger than the 3800-Watt generator, so there will be some excess.
This would be the best available solution we have for this particular... view full answer...
It looks like the overall length of the 2022 Flag Staff E PRO Model 19FD is 20' 8" including the tongue but covers aren't supposed to fit over the tongue. The Adco Olefin HD All-Climate + Wind RV Cover # AD97ZR you're looking at is for travel trailers 18'1" - 20' long. Since the tongue of a trailer is somewhere around 3' long you might need to use the next size down which is part # AD37ZR and fits travel trailers 15'1" - 18' long.
Your dealer should be able to measure out just the box... view full answer...
Hi Teri,
We can get you a bike rack for your E-Pro travel trailer, but first you'll need a hitch (assuming one is not already on the camper). For that you'll need the Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide # 13703.
This can be welded or bolted onto your trailer and gives you a 2" hitch for a rack. The rack does need to be travel-trailer approved, and for that use the Swagman Nomad Bike Rack for 2 Bikes # S36FR.
What I like about the Nomad is it's 8" rise so... view full answer...
On your 2017 Forest River E-Pro E17PR, from what I can find online you have a Dexter Torflex axle # 10. For this you will want the Torflex Lift Kit # K71-707-01 which is designed for that Torflex # 10 Axle with capacities between 2,300 and 4,000 lbs. This will raise your trailer height 2-5/8 inches and is easy to install. view full answer...
The Curt Ball Mount for 2" Hitches part # C84WR has an 8,000 lb weight capacity which is for both rise and drop positions. In regards to fit, this will vary by receiver, some are tighter than others and some are looser. It comes down to both the hitch side and ball mount side. That said, if you're worried about rattle you can add an anti-rattle like the Curt Anti-Rattle Hitch Clamp for 2" Hitches part # C27UR. view full answer...
For RVs like your 2022 Forest River Flagstaff E-Pro 19BH the best hitch option we have is the Curt # 13703 which is a universal fit style hitch that fits frame styles between 22 and 72 inches apart. view full answer...
The Adco Polypropylene Storage Lot RV Cover for Travel Trailer # 290-74839 will fit your 2019 Forest River Flagstaff E-Pro Travel Trailer just fine.
This cover is intended to fit trailers up to 217" long (18') so there will be enough room to cover your ladder as well.
Additionally, this cover is made from heavy-duty, UV-treated 4-layer polypropylene fabric that will prevent fading and cracking, and eliminates black streaks and corrosion. view full answer...
The correct slide topper awnings for a 2020 Forest River Flagstaff E-Pro with a 154" wide slide and 83" wide slides are as follows:
154" Wide Slide: Solera RV Slide-Out Awning part # LCV000168109 for Black or part # LCV000163300 for White
83" Wide Slide: Solera RV Slide-Out Awning part # LCV000165062 for Black or part # LCV000163287 for White
Please note, slide-outs need to be measured from the outside of each slide. view full answer...
The Adco SFS AquaShed Covers for Bumper Pull Trailers work great on v-nose trailers, if from the nose to the rear of the trailer measures no more than 14' or 168" then you can use part # 290-46003. If the trailer measures greater than 14' but not 16' then you can use part # 290-46004. view full answer...
We haven't been able to determine the axle capacity of your travel trailer so we aren't sure exactly what bearings you'd need. If you can get me the axle capacity I can let you know what you'd need.
Most likely you have a 3,500 lb axle which would require the bearing kit part # BK2-100, but other common options would be the # BK1-150 for a 2,200 lb axle or # BK3-300 for a 5,200 lb axle. view full answer...
The Adco Olefin HD RV Cover for Travel Trailers up to 18' item # AD37ZR you were looking at is the best option for to cover your 2019 Forest River Flagstaff E-Pro 19QB travel trailer. The roof is white in color to reflect UV rays and keep the camper cooler. While the triple-layer polypropylene ensures the cover is strong enough to resist strong winds.
Along with the high-quality top panel, this cover also has side panels that are triple-layered and vented, making them breathable so heavy... view full answer...
Though you will not need to make any alterations to the axle to up your bolt pattern to a 5 on 4-1/2, but you will need to verify your bearings to make sure the new hubs will fit properly. Form what I could find, your 2018 Forest River Flagstaff E-Pro E14FK has a GVWR of 2,917 pounds. This means you most likely have a 3,500 pound Dexter axle.
The typical Dexter axle of this capacity will use the # L68149 inner bearing and # L44649 outer bearing. Again, you will need to verify these bearings,... view full answer...
In order to switch to a 5 on 4-1/2 bolt pattern you are going to need a new hub and drum assembly. In order to select the correct one, you will need to figure out your axle capacity and what bearings fit your spindle.
Assuming your trailer has a 3,500 lb axle using the # L68149 inner and # L44649 outer bearing, you would be looking at the # 84546UC3 of if you have E-Z lube axles the # AKHD-545-35-EZ-K instead.
I recommend pulling off your current hub and drum assembly and looking at... view full answer...
Go To Results