You're in luck because there are custom mounting brackets for a snow plow that fit your 1976 Ford F-250 (so long as it is not a SuperCab model), the Custom Mounting Brackets for Detail K2 Snowplows # K281501. These mounting brackets work with the following snow plows:
- Detail K2 Summit II Snowplow # K2SUMM8826
- Detail K2 Summit II Elite Snowplow - Electric Actuator # K2SUMM8826ELT view full answer...
I have a solution for you. Unfortunately, the Westin Fey Diamondstep # 73000 will not fit your 1977 Ford F-250. However, for the correct bumper and mounting hardware, you need the Westin Fey Diamondstep Rear Bumper with Custom Installation Kit # 21000-92230. This bumper comes with the same chrome style as the # 73000. Also, it comes with all mounting hardware include for a quick bolt-on installation.
It is important to note that this bumper will only fit standard beds. If you do not have... view full answer...
Technically you could use RV hitch # 5350 on your 1972 Ford F-100. This would likely require drilling holes into the truck frame though. Otherwise I do not see a reason why it wouldn't work for you. We even had a customer put it on a 1957 Ford. So this hitch gets around but in a good way.
I also recommend ball mount kit # EBMK4 which comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip and a storage bag. If the ball mount does not... view full answer...
We have a universal mat that should fit the bed of your 1964 F-100 since you have the 8' bed. It is the DeeZee Universal Utility Mat for Trucks and Trailers Item # DZ85005. This bed mat is 8' long x 4' wide. This 3/8" thick rubber mat has a non-skid surface that prevents cargo from shifting.
I have linked a review video below so you can take a look at this mat being installed and used.
There are no custom fit options for a 1964 F-100. view full answer...
Yes, the Tow Ready Mounting Harness # 18144 will wok with the Curt T-connector Harness, # C55301.
The mount can connect at the bumper of your vehicle to mount the 4-flat plug of the Curt harness. view full answer...
From the picture that you sent in it looks like your vent cover has a continuous hinge. If that is the case then you just need to confirm that it measures 14" x 14".
If it does meet those requirements then the Replacement Lid for Elixir RV Roof Vent # CAM40156 will fit!
You could also use the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BV0534-00 or the Smoke Replacement Lid for Ventline and Elixir RV Roof Vents # CAM40148 as well depending on what you are... view full answer...
We do have a solution for you, though the Reese Trailer Connector Adapter # 78118 will not work for you.
Instead I recommend the Hopkins Endurance Quick-Install Trailer Connector Adapter # HM47200 which will plug into your truck's 4-way and allow you to connect your trailer's 7-way. view full answer...
While we don't carry any custom-fit options for a 1966 Ford F-100 we do offer universal-fit options like the DeeZee Universal Utility Mat for Trucks and Trailers # DZ85005. DeeZee also offers a universal-fit tailgate liner # DZ86700 in a similar style to help protect your truck bed.
Both of these universal-fit mats can be trimmed to fit your bed and tailgate. view full answer...
The B&W Trailer Hitch # BWHDRH25122 is a confirmed fit for a 1970 Ford F-250 pickup with a standard or step bumper, regardless of if it is a 4WD or 2WD, and is designed to allow fits for both 34 and 37-1/2 inch frames. view full answer...
Thank you for the photo of your 1975 Ford F-250.
Thse tie-downs are a universal fit. As long as there is clear access to the underside of the bed rails on your 1975 Ford F-150 you can use theExtang CargoCleats Truck Bed Tie-Down Anchors # EX1932.
The linked review videos show you more about these items. view full answer...
When it comes to covers you really don't want to get something too small and try to make it work. It would be better to get something a little too large and have extra. Instead of getting a cover for a 28 inch spare tire I suggest the Camco Vinyl Spare Tire Cover # CAM45344 which is designed for 29 inch tires. view full answer...
The Access TonnoSport Soft, Roll-Up Tonneau Cover # A22010029 will fit the 6' Fleet side bed on your 1979 Ford F-100. I don't have the exact dimensions of this cover (all of the tonneau manufacturers just reply to that question with "it fits") but the "Standard Bed" we have listed in our fitguide is the Fleet side so you're good to go! view full answer...
The Draw-Tite Trailer Hitch Receiver # 41504 is a custom fit hitch for specific trucks. The trucks it fits have a frame spacing of either of 34 or 38 inches.
Since you're going to need something more universal for your 1949 F3 you may like the Curt # C13701 that fits frames between 18 and 51 inches wide. Or if you can tell me the width of your truck's frame, center on center, I can wee if we have other options available. view full answer...
We do have one option we know will work as a replacement vent lid for a Heng's, which is a universal option from MaxxAir, and as you can see by the accompanying cut out, the hinge will attach right onto the frame of your vent. The MaxxAir UniMaxx is available in either smoke or white:
- Smoke: MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent # MA00-335002
- White: MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent # MA00-335001
I have added links... view full answer...
Outstanding photos thank you so much for sending them, and based on that we do have a hitch that can fit your 1965 Ford F-250 with a custom bumper. Since the frame is clear from any interference with the bumper, all you need to do is measure from the frame to the bottom of the bumper and see what that distance is. If that distance is 7-1/4 inches or less there is a hitch you can use:
- Curt Trailer Hitch Receiver # C13099
The reason why is the Curt # C13099 measures 7-1/4 inches from... view full answer...
I do have some dimensions of the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75034 which is a fit for a 1965 Ford F-100 and I have attached these for you below but I would not be able to provide a dimensional drawing as this is proprietary information that is not released by the manufacturer.
The distance from the frame to the top of the receiver tube opening is 5-5/8" which will allow you to determine how far under the rear bumper the receiver tube will sit. In regards to exhaust... view full answer...
We do have hitches available for your truck (see link) but none of them are designed to fit behind the tag (license plate). At this time I do not know of a Hidden or Stealth hitch that is available for your truck.
For a trailer hitch that would sit below the rear bumper, I recommend looking at the Draw-Tite Class III Trailer Hitch, # 75034. This hitch will fit as long as you have the standard or step bumper.
If you have a deep drop bumper, then you will want part # 41504. view full answer...
I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers.
We have two bumpers that have been determined to be a fit for your truck with a factory bumper. The # BWHDRH25122 is for standard and step bumpers and the # BWHDRH25198 is for deep drop bumpers. I recommend measuring from your frame to the bottom of your bumper to know how much distance you will need... view full answer...
To install the Detail K2 Rampage II Snowplow # K2RAMP8219 you only need add Custom Mounting Brackets # K281516. The brackets install directly into your F-250's frame so as long as the lift kit on your truck does not have any interference with the frame the brackets will work.
These brackets are a fit for a 1983 Ford F-250 4 wheel drive, bolting onto your truck's frame. Those are the only two items you will need to assemble and plow snow. view full answer...
I recommend the Curt Class III Trailer Hitch Receiver # 13028 for your 1979 Ford F-250. This hitch will fit either the standard bumper or the deep drop bumper. It will however, not fit if you have lower rear fascia or a rollpan or tube bumper. It is a bolt on installation but does require some drilling.
For trailer wiring you can use the Tekonsha Wiring Harness # 18252. This will add a 4-pole onto the back of your truck and includes quick-splice connectors to make it easier to hardwire.
If... view full answer...